• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.118-122
• /
• 2000

In this study, Ringing is investigated by continuous wavelet transform. Ringing is considered to be one of the typical transient phenomena in the field of ocean engineering. The wavelet analysis is adopted to analyze ringing from the point that wavelet analysis is capable of frequency analysis as well as time domain analysis. The use mother wavelet is the Morlet wavelet. The relation between the frequency of the time series and that of wavelet can be clearly defined with Mor1et wavelet. Experimental data obtained by other researchers was used. The wave height time series and acceleration times series of the surface piercing cylinder were analyzed. The results show that the proposed scheme can detect typical frequency region by the time domain analysis which could hardly be detected if one relied on the frequency analysis.

• 산업기술연구
• /
• 제15권
• /
• pp.123-135
• /
• 1995

In this paper, we performed the modeling of a tunable three section DFB-LD with continuous phase using the coupled-wave equation. It was also proposed new modeling method for ${\lambda}/4$ phase shifted one. We got the characteristics of oscillation wavelength, gain, and photon density profiles according to parameters such as coupling coefficient K and current into the third sections for two case of continuous phase and ${\lambda}/4$ shifted phase one. The simulations for ${\lambda}/4$ phase shifted tunable three section DFB-LD prove that the continuous tuning range is about 4.2nm for $K=120cm^{-1}$, $L=180{\mu}m$, and the oscillation mode be within the stop-bands. Also when changed a current of both end sections, it is shown that a photon density reaches the maximum at the center.

• 한국군사과학기술학회지
• /
• 제20권1호
• /
• pp.63-71
• /
• 2017

During the sea trial test, we discovered EMI(Electromagnetic Interference) between MIL-SATCOM parabolic antenna and ES(Electronic Warfare Support) omni antenna. Emitted side lobe of CW(Continuous Wave) from MIL-SATCOM raises the threshold level of ES omni antenna. Therefore detection rate of ES is decreased. To solve this problem, the path of side lobe of CW from MIL-SATCOM should be blocked using EMI shield. This paper presents the method how to calculate the size of EMI shield, material, and optimized deployment. The test of the EMI shield effect was performed on a surface ship. After installing EMI shield, EMI has been decreased significantly. This paper will provide a method how to design EMI shield and a way to verify the result.

• 한국군사과학기술학회지
• /
• 제19권6호
• /
• pp.690-697
• /
• 2016

EOIS(electro-optical imaging system) is the main target of the laser weapon. Specially, the image sensor will be vulnerable because EOIS focuses the incident laser beam onto the image sensor. Accordingly, the laser-induced damage of the image sensor needs to be identified for the counter-measure against the laser attack. In this study, the laser-induced damage of the CCD image sensor irradiated by the CW(continuous wave) NIR(near infrared) laser was experimentally investigated and mechanisms of those damage occurrences were analyzed. In the experiment, the near infrared CW fiber laser was used as a laser source. As the fluence, which is the product of the irradiance and the irradiation time, increased, the permanent damages such as discoloration and breakdown appeared sequentially. The discoloration occurred when the color filter was damaged and then the breakdown occurred when the photodiode and substrate were damaged. From the experimental results, LIDTs(laser-induced damage thresholds) of damages were roughly determined.

• 한국군사과학기술학회지
• /
• 제18권3호
• /
• pp.293-299
• /
• 2015

We analyzed the damage effect on Glass Fibre Reinforced Plastics(GFRP) under air flow by irradiation of continuous wave near-IR laser. Damage process and temporal temperature distribution were demonstrated and material characteristics were observed with laser intensity, surface flow speed and angle. Surface temperature on GFRP rapidly increased with laser intensity, and the damaged pattern was different with flow characteristics. In case of no flow, penetration on GFRP by burning and flame generation after laser irradiation was appeared at once. GFRP was penetrated by the heat generated from resin ignition. In case of laser irradiation under flow, a flame generated after burning extinguished at once by flow and penetration pattern on GFRP were differently shown with flow angle. From the results, we presented the damage process and its mechanism.

• 한국광학회지
• /
• 제13권1호
• /
• pp.65-69
• /
• 2002

불소원자(F)와 D$_2$ 기체 발열반응에 의해 레이저 이득매질인 DF 여기분자를 생성시키는 구조의 연속발진형 불화중수소 (DF)화학 레이저를 설계, 제작하고 발진 실험을 수행하였다. 불소원자는 F$_2$ 기체와 H$_2$ 기체를 연소시켜 생성시키고, 불소원자를 초음속 노즐을 통과시킨 직후에 D$_2$ 기체를 분사하여 형성된 DF 여기분자 초음속 흐름을 활성 매질로 사용하여 레이저를 발진시켰다. 본 연구에서 얻은 레이저 발진 출력은 101W이며, 최적의 유량조건에서 얻은 화학 효율은 5.12%, 비출력은 96.5 J/g이다.

• 수산해양기술연구
• /
• 제35권3호
• /
• pp.284-290
• /
• 1999

This paper describes a Frequency Shift Keying (FSK) modulator and demodulator and the experimented underwater data ommunication equipment to transfer the analog echo signal in real-time from an underwater vehicle to the mother ship. The system consists of an echo signal transfer unit equipped to the vehicle and an ultrasonic receiver equipped on the ship. The former includes an ultrasonic transceiver unit of 180kHz for echo detection and a continuous wave transmitter of 50kHz with a FSK modulator for echo transmission to the ship. The latter includes an ultrasonic receiver of 50kHz and the FSK demodulator. The results of experiment are as follows. 1. The characteristics of the FSK modulating and demodulating circuits designed with the use of C-MOS IC 4046 was good and confirmed its usefulness in underwater data communication system.2. The prototype ultrasonic transceiver unit shows profitable driving power while the pulse duration was short less than 3 msec, but it was found that the driving power is not sufficient while the long pulse duration or continuous wave is used. The gain of the ultrasonic receiver was 80 dB and the receiving bandwidth 700Hz (at - 3 dB point).3. It was found that the system designed by the author has some possibility to use in underwater echo transfer.4. At the FSK modulator, the widths of voltage and frequency which represent linearity were 3.5 V, 1600Hz, respectively, at the FSK demodulator 2.6 V, 700Hz, respectively.

• 수산해양기술연구
• /
• 제35권3호
• /
• pp.285-285
• /
• 1999

This paper describes a Frequency Shift Keying (FSK) modulator and demodulator and the experimented underwater data ommunication equipment to transfer the analog echo signal in real-time from an underwater vehicle to the mother ship. The system consists of an echo signal transfer unit equipped to the vehicle and an ultrasonic receiver equipped on the ship. The former includes an ultrasonic transceiver unit of 180kHz for echo detection and a continuous wave transmitter of 50kHz with a FSK modulator for echo transmission to the ship. The latter includes an ultrasonic receiver of 50kHz and the FSK demodulator. The results of experiment are as follows. 1. The characteristics of the FSK modulating and demodulating circuits designed with the use of C-MOS IC 4046 was good and confirmed its usefulness in underwater data communication system.2. The prototype ultrasonic transceiver unit shows profitable driving power while the pulse duration was short less than 3 msec, but it was found that the driving power is not sufficient while the long pulse duration or continuous wave is used. The gain of the ultrasonic receiver was 80 dB and the receiving bandwidth 700Hz (at - 3 dB point).3. It was found that the system designed by the author has some possibility to use in underwater echo transfer.4. At the FSK modulator, the widths of voltage and frequency which represent linearity were 3.5 V, 1600Hz, respectively, at the FSK demodulator 2.6 V, 700Hz, respectively.

• 한국공작기계학회논문집
• /
• 제12권3호
• /
• pp.58-67
• /
• 2003

Welding characteristics of austienite 304 stainless and SM45C using a continuous wave Nd:YAG laser n experimentally investigated Laser beam welding is increasingly being used in welding of structural steels. The laser welding process is one of the most advanced manufacturing technologies owing to its high speed and deep penetration. The thermal cycles associated with laser welding are generally much Inter than those involved in conventional welding processes, leading to a rather small weld zone. Experiments are performed for 304 stainless steel plates changing several process parameter such as laser power, welding speed, shielding gas flow rate, presence of surface pollution, with fixed or variable gap and misalignment between the similar and dissimilar and plates, etc. The Nd:YAG laser welding process is one of the most advanced manufacturing technologies owing to its high speed and penetration. This paper describes the weld ability of SM45C carbon steel for machine structural use by Nd:YAG laser. The follow conclusions can be drawn that laser power and welding speed have a pronounced effect on size and shape of the fusion zone. Increase in welding speed resulted in an increase in weld depth/aspect ratio and hence a decrease in the fusion zone size. The penetration depth increased with the increase in laser power.

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.252-258
• /
• 2012

A study of terahertz waves was made for the nondestructive evaluation of FRP (Fiber reinforced plastics) composite materials. The terahertz systems were consisted of time domain spectroscopy (TDS) and continuous wave (CW). The composite materials investigated include both non-conducting polymeric composites and conducting carbon fiber composites. Terahertz signals in the TDS mode resembles that of ultrasound; however, unlike ultrasound, a terahertz pulse was not able to detect a material with conductivity. The CFRP (Carbon fiber reinforced plastics) laminates were utilized for confirming the experimentation in the terahertz NDE. In carbon composites the penetration of terahertz waves is quite limited and the detection of flaws is strongly affected by the angle between the electric field direction of the terahertz waves and the intervening fiber directions. A refractive index (n) was defined as one of mechanical properties; so a method was obtained in order solve the "n" in the material with non-conductivity. The usefulness and limitations of terahertz radiation are investigated for the NDE of FRP composites.