• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.10 s.241
• /
• pp.1156-1162
• /
• 2005

In this study, a noble method is proposed to prevent the edge overcoating (EOC) that may develop near the edge of the steel strip in the gas wiping process of continuous hot-dip galvanizing. In our past study (Trans. of the KSME (B), Vol. 27, No. 8, pp. $1105\~1113$), it was found that EOC is caused by the alternating vortices which are generated by the collision of two opposed jets in the region outside the steel strip. When the two opposed jets collide at an angle much less than $180^{o}$, non-alternating stable vortices are established symmetrically outside the steel strip, which lead to nearly uniform pressure on the strip surface. In order to deflect both jets downward by a certain angle, a cylinder with small diameter is installed tangentially to the exit of the lower lip of the two-dimensional jet. In order to find an optimum cylinder diameter, the three dimensional flow field is analysed numerically by using the commercial code, STAR-CD. And the coating thickness is calculated by using an integral analysis method to solve the boundary layer momentum equation. In order to compare the present noble method with the conventional baffle plate method to prevent the EOC, the flow field with a baffle plate is also calculated. The calculation results show that the tangentially installed cylinder at the bottom lip of the jet exit is more effective than the baffle plate to prevent EOC.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.12
• /
• pp.938-942
• /
• 2009

In this paper, we propose a novel filtering method for processing continuous skyline queries on wireless sensor network environments. The existing filtering methods use the filter based on router paths. However, because these filters are applied not to a whole area but to a partial area, these methods send almost data of sensor nodes to transmit to the base station and have no sufficient effect in terms of energy efficiency. Therefore, we propose an efficient method to dramatically reduce the transmission data of sensors through applying a low-cost and effective filter to all sensor nodes. The proposed effective filter is generated by using characteristics such as the data locality and the clustering of sensors. An extensive performance study verifies the merits of our new method.

• Journal of KIISE:Software and Applications
• /
• v.36 no.1
• /
• pp.82-91
• /
• 2009

Sign language spotting is the task of detecting and recognizing the signs in a signed utterance. The difficulty of sign language spotting is that the occurrences of signs vary in both motion and shape. Moreover, the signs appear within a continuous gesture stream, interspersed with transitional movements between signs in a vocabulary and non-sign patterns(which include out-of-vocabulary signs, epentheses, and other movements that do not correspond to signs). In this paper, a novel method for designing a threshold model in a conditional random field(CRF) model is proposed. The proposed model performs an adaptive threshold for distinguishing between signs in the vocabulary and non-sign patterns. A hand appearance-based sign verification method, a short-sign detector, and a subsign reasoning method are included to further improve sign language spotting accuracy. Experimental results show that the proposed method can detect signs from continuous data with an 88% spotting rate and can recognize signs from isolated data with a 94% recognition rate, versus 74% and 90% respectively for CRFs without a threshold model, short-sign detector, subsign reasoning, and hand appearance-based sign verification.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.3
• /
• pp.397-404
• /
• 2011

In this research, wish to suggest method to embody system that can accommodate defect of PLC and find actual propriety. Defect permission control system minimizes production damage because enables repair and checking without discontinuance and improve believability about whole system. Propose duplexing of system to embody this fault tolerant system. Therefore, composed control system that can permit defect or breakdown duplexings of various module proposing this system, and confirms to simulation and actuality kiln of defect permission control system through an application experiment, and compares for mean time between defect by estimate and defect special quality and system configuration of failure(failure) to improve believability of PLC control system together. In proposed system expression method and system mode and relation with operation mode, error discovery mode and switching tube of duplexing mode, and PLC's central processing unit of node study algorithm about master-standby conversion driving and continuous operation of 2 channels method that have 2 that is not one and deduced continuous operation method and result about defect permission in this algorithm and applies this result to actuality kiln control system and confirms continuous operation about PLC defect permission.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.2
• /
• pp.477-487
• /
• 2000

When volume data is visualized by the ray casting method, the color value of each pixel in the image is obtained by composing the color contributions of the sample points that lie on the ray cast from the pixel point. In most ray tracing methods including Levoy's classical method, the color composition is formulated as a summation of the color contributions of the discrete sample points. However, the more precise color composition is formulated as differential equations over the color contributions of the continuous sample points. The discrete formulation is used, because analytical solutions to the continuous formulations are hard to find. In this paper, however, we have discovered a semi-analytical solution to the continuous formulation of a typical ray tracing of volume data. We have applied both Levoy's method and ours to the same set of data, and compared the visual quality of both results. The comparison shows that our method produces a more fine-grained visualization of volume data.

• Membrane Journal
• /
• v.29 no.4
• /
• pp.216-222
• /
• 2019

In this study, permeation experiments were conducted using naturally circulating spherical beads, backwashable plate membrane and the air supplied from the bottom of the MBR. The activated sludge solution was maintained at 8,000 mg/L of MLSS and compared transmembrane pressure (TMP) with respect to FR (filtration and relaxation), FR/BW (filtration and relaxation/backwashing), SFCO (sinusoidal filtration continuous operation) and SFCO/BW (sinusoidal filtration continuous operation/backwashing). As the backwashing flux decreased from 47 to $14L/m^2{\cdot}hr$, the TMP increased generally, but the TMP of FR system increased significantly comparing with SFCO. In addition, the backwashing method reduced more TMP comparing to the cleaning method using spherical beads, and it was confirmed that the operation method using the spherical beads and the backwashing simultaneously is more effective than each method.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.11
• /
• pp.969-974
• /
• 2014

Previously fabricated electronic devices were used for vacuum manufacturing processes such as conventional semiconductor manufacturing. However, they are difficult to apply to continuous processes such as roll-to-roll printing, which results in very high device manufacturing and processing costs. Therefore, many developers have been interested in applying continuous processes to contact printing or noncontact printing technologies and they proposed various continuous printing techniques instead of conventional batch coating. In this paper, we proposed improved gravure offset printing process as one of the contact printing technique. We used etching pattern geometry with soft core blanket roll for printing of ultra fine line below the 10um.Using this technique we obtained flexible metal grid mesh film as transparent conductive film.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.9
• /
• pp.755-760
• /
• 2005

This paper proposes an improved implementation algorithm for the continuous-time receding horizon control (RHC). The proposed algorithm has a feature that it has better control performance than the existing algorithm. Main idea of the proposed algorithm is that we can approximate the original RHC problem better by assuming the predicted input trajectory on the prediction horizon has a continuous form, which is constructed from linear interpolation of finite number of vectors. This, in turn, leads to improved control performance. We derive a predictor such that it takes linear interpolation into account and proposes the method by which we can express the cost exactly. Through simulation study fur an inverted pendulum, we illustrate that the proposed algorithm has the better control performance than the existing one.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.194-197
• /
• 2012

The purpose of the thesis is to develop a module which can measure precise Continuous Cardiac Output(CCO) better than existing equipments for the critical cardiopulmonary patient diagnosis purpose. This module enables more precise and effective diagnosis and treatment for the patient by compensating old method which injected cold liquid to inside of heart to measure the CCO.

• Journal of Digital Convergence
• /
• v.10 no.9
• /
• pp.339-344
• /
• 2012

Established continuous vocabulary recognition system improved recognition rate by using decision tree based tying modeling method. However, since system model cannot support the retrieve of phoneme data, it is hard to secure the accuracy. In order to improve this problem, we remodeled a system that could retrieve probabilistic model from continuous vocabulary clustering model to phoneme unit. Therefore in this paper showed 95.88%of recognition rate in system performance.