• Journal of Oral Medicine and Pain
• /
• v.20 no.2
• /
• pp.327-334
• /
• 1995

In order to observe the influence of pulsed Nd:YAG laser at its out-of-contact with dentin on tooth temperature, we have applied pulsed Nd:YAG laser to 2mm thick dentin sample at a point of contact and from a distance of 1mm, 2mm, 3mm and 4mm with an energy of 0.3W, 0.5W, 0.8W, 1.5W and 2.0W. They were exposed to periods of 3 seconds, 6 seconds, 9 seconds and 15 seconds respectively and measured temperature changes. The results as follows : 1. When the time ad intensity of power were constant, the temperature changes on dentin of tooth depended on the distance. The temperature increased when the laser intensity increased bu two other conditions were contact. 2. At the point of contact, the temperature has risen over $5^{\circ}C$ regrdless of intensity of the power or the time. However, there was $5^{\circ}C$ fluctuation with 0.3 W for 3 seconds treatment. 3. The temperature change was less than $5^{\circ}C$ thermal change at the distance of 1mm and 2mm respectively when lased for 3 seconds, 6 seconds, 12 seconds and 15 seconds with 0.3 W. Similar results were observed at 3 and 6 seconds treatment with 0.5 W and at 3 seconds treatment with 0.8 and 1.0W respectively. 4. It showed less than 5(C thermal change when lased for 3 seconds, 6 seconds, 9 seconds, 12 seconds and 15 seconds with 0.3W at the distance of 3mm and 4mm. The same results were seen in 3 seconds, 6 seconds and 9 seconds treatment with 0.5W and in 3 seconds with 0.8W and 1.0W respectively. As we have seen the above, the results has indicated that pulsed Nd:YAG lasing at its off contact on dentin of 2mm thickness will not cause irreversible changes if lasing intensity, lasing distance and lasing time are appropriate.

• Journal of Korean Society on Water Environment
• /
• v.20 no.6
• /
• pp.708-713
• /
• 2004

This study was performed to investigate the variations of hydrophilic and hydrophobic organic matter fractions in soluble organic matter according to livestock wastewater treatment by ionized gas and coagulation effect to these fractions after ionized gas contact. As a result of experiment, because of ionized gas contact, particle in the surface of livestock wastewater was more smaller and the result was consisted of particle size analysis and the amount of small size was increased. Also, we confirmed that organic matters in livestock wastewater by ionized gas contact were removed. The relation equation between ionized gas contact time(X) and $TCOD_{cr}$(Y) was shown as yscale(y)=3.748-0.431* xscale(X). That between ionized gas contact time(X) and $TCOD_{cr}$(Y) was yscale(y)=3.283-0.463* xscale(X). As respects the HPL(hydrophilic matter)and HPO(hydrophobic matter) fractions of raw in livestock wastewater treatment plant, HPL fraction was 53.2% and HPO fraction was 46.8%. But, HPO fraction according to ionized gas treatment was increased at 30min and after that time, HPL fraction was increased. Also, when we performed coagulation process after ionized gas treatment of raw wastewater, the removal efficiency of organic matter was the highest at 30min of ionized gas treatment because of the variation of HPL and HPO fractions in organic matter by ionized gas. In coagulation process following after ionized gas process, HPO was removed more effective than HPL.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1336-1341
• /
• 2011

The pantograph-overhead contact line system is an interface that supplies power to high-speed trains used in many countries including Korea. Due to the fact that power is supplied through direct contact between contact wires and contact strips, wear may occur, increasing the possibility of accidents over periods of time. Therefore, there is a need to establish methods of effectively extracting safety related parameters. In this paper, an image processing based method that calculates and draws graphs of a pantograph's dynamic stagger is proposed. To assess reliability, the results were compared with data collected from conventional maintenance vehicles.

• Transactions of Materials Processing
• /
• v.9 no.3
• /
• pp.274-283
• /
• 2000

A dynamic explicit finite element code for simulating sheet forming processes has been developed. The code utilizes the discrete Kirchhoff shell element and contact force is treated by a conventional penalty method. In order to reduce the computational cost, a new and robust contact searching algorithm has been developed and implemented into the code. In the method, a hierarchical structure of tool segments is built for each tool at the initial stage of the analysis. hierarchical structure is built in a way to divide a box to 8 sub-boxes, 2 in each direction, until the lowest level of the hierarchical structure contains exactly one segment of the tool or empty. Then at each time step, contact is checked from the box to sub-boxes hierarchically for each node. Comparisons of computational results of various examples with the existing ones show the validity of the method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1262-1265
• /
• 2004

A cycloidal speed reducer is a type of the speed reducers of machinery. The cycloidal speed reducer consists of two cycloidal plate gears, housing roller gear, input shaft, output pin and shaft, and eccentric bearings. Especially the cycloidal plate gear has the peculiar parts of the teeth, because of gearing with the housing roller gear that has the several rollers on the circular line. And then all teeth on the cycloidal plate gear can be designed to contact with the rollers on the housing roller gear at the same time. Therefore the cycloidal plate gear has always contact motion with rollers and the force is interacted between roller gear with cycloidal plate gear. Because the contact force and friction force must be required to improve the accuracy in design procedures of cycloidal speed reducers, this paper presents a force analysis considered friction effect approach derived by static force equilibrium condition, geometrical adaptation, instant velocity center method and relative velocity method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.5
• /
• pp.345-350
• /
• 2011

This paper was carried about optimization for high efficiency of point contact solar cell. We have studied on the characteristics of power converter according to each parameter for the optimization for high efficiency of point contact solar cell on this study. We have 25.1352% of convert efficiency after adapt optimal parameters as mentioned in point body and superior conclusion is drawn by comparison with general efficiency has within 20%. At this time, the value of parameter is 100 um cell pitch, 0.01 um AR coating, 0.9 um N+ FSF thickness., etc. This study will continue to go on for optimization for efficiency in future, as it looks now, the results of this study would contribute to the business of high efficiency of point contact solar cell.

• Journal of Mechanical Science and Technology
• /
• v.14 no.3
• /
• pp.331-337
• /
• 2000

A numerical procedure for contact analysis and calculating subsurface stress was developed. The procedure takes the advantage of signal processing technique in frequency domain to achieve shorter computing time. Boussinesq's equation was adopted as a response function in contact analysis. The validity of this procedure was proved by comparing the numerical results with the exact solutions. The fastness of this procedure was also compared with other algorithm.

• Journal of Multimedia Information System
• /
• v.5 no.3
• /
• pp.179-188
• /
• 2018

In order to overcome the problems of contact palmprint recognition, a non-contact palmprint recognition system is developed on personal computer (PC) platform. Three methods, namely "double-line-single-point" (DLSP), "double-assistant-crosshair" (DAC) and "none-assistant-graphic" (NAG), are implemented for the palmprint localization to solve the severe technical challenges, including the complex background, variant illuminations, uncontrollable locations and gestures of hands. In NAG, hand segmentation and the cropping of region of interest are performed without any assistant graphics. The convex hull contour of hand helps detect the outside contour of little finger as well as the valley bottom between thumb and index finger. The three methods of palmprint localization have good operating efficiency and can meet the performance requirements of real-time system. Furthermore, an attendance system on PC platform is designed and developed based on non-contact palmprint recognition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.383-388
• /
• 2008

A modeling method for the impact analysis of plate structures employing Hertzian contact theory is presented in this paper. Since local deformation as well as bending deflection of the plate occurs due to the collision, it has to be considered for the impact analysis. When the coefficient of restitution is employed for the impact analysis, the local deformation is not considered. For more accurate and reliable impact analysis, however, the local deformation should be considered. The effects of the location of collision and the collision mass on the impact duration time and the contact force magnitude are investigated through numerical studies employing Hertzian contact theory.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.188-191
• /
• 1997

In the recent sheet metal forming simulations, it increases to adopt the dynamic explicit method for an effective computation and the elastic-plastic formulation for stress recovery. It is inevitable in the dynamic explicit method that some noises occur and sometimes partly spoil results of simulations. It is severer when complicated contact conditions are included in simulations. An effective method to control these noises is introduction of damping effects. In this paper, the concept of contact damping is introduced in order to suppress noises due to complicated contact conditions. This is checked by analyzing a simple sheet metal forming process(U-bending). From the computational results, it is shown that the contact damping can effectively control the noises due to contacts and develop more reliable internal stress states.