• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.10
• /
• pp.1827-1832
• /
• 2017

To observe the characteristics to be a resistive memory of $V_2O_5$ deposited by oxygen various gas flows and annealed, the hysteresis curves of $V_2O_5$ were analyzed. The good resistive memory was obtained from the electrical characteristics of $V_2O_5$ films with the Schottky contact as a result of electron-hole pair, and the oxygen vacancy generated from the annealing process contributes the high quality of Schottky contact and the formation of resistive memories. The balanced Schottky contacts owing to the oxygen vacancy effect as the result of an ionic reaction were formed at the $V_2O_5$ film annealed at $150^{\circ}C$ and $200^{\circ}C$ and the balanced Schottky contact with negative to positive voltages enhanced the electrical operation with write/erase states according to the forward or reverse bias voltages for the resistive memory behavior due to the oxygen vacancy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1049-1055
• /
• 2004

Chemical Mechanical Polishing (CMP) is referred to as a three body tribological system, because it includes two solids in relative motion and the CMP slurry. On the assumption that the abrasives between the pad and the wafer could be a major reason not only for the friction force but also for material removal during polishing, the friction force generated during CMP process was investigated with the change of abrasive size and concentration of CMP slurry. The threshold point of average coefficient of friction (COF) with increase in abrasives concentration during interlayer dielectric (ILD) CMP was found experimentally and verified mathematically based on contact mechanics. The predictable models, Mode I (wafer is in contact with abrasives and pad) and Mode II (wafer is in contact with abrasives only), were proposed and used to explain the threshold point. The average COF value increased in the low abrasives concentration region which might be explained by Mode I. In contrast the average COF value decreased at high abrasives concentration which might be regarded to as Mode II. The threshold point observed seemed to be due to the transition from Mode I to Mode II. The tendency of threshold point with the variation of abrasive size was studied. The increase of particle radius could cause contact status to reach transition area faster. The correlation between COF and material removal rate was also investigated from the tribological and energetic point of view. Due to the energy loss by vibration of polishing equipment, COF value is not proportional to the material removal rate in this experiment.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.1
• /
• pp.1-8
• /
• 2002

Various kinds of aerosols such as a mixture of hairspray resin and its solvents, a perfume, a soap water, and ask in-lotion were sprayed onto the contact lens which was mounted on the eye-model made of wood, varying the parameters as the distance between nozzle and contact lens and the spraying time duration. In the case of both the hairspray and the perfume including an ethanol as solvents, the shape of contact lenses has changed tremendously Jess than 1 minute after the exposure to the aerosol particles and then it continued until the lens surfaces were completely flipped over. Driving force for the lens distortion seems to be the expansion coefficient difference between the inner and outer surface of lens, which was caused by the heat of vaporization of ethanol included in the aerosol and subsequent temperature decrease induced on the lens surface.

• Journal of the Korean Society of Physical Medicine
• /
• v.10 no.4
• /
• pp.49-57
• /
• 2015

PURPOSE: This study aimed to investigate the effect of emphasized initial contact gait training on balance and gait ability in hemiplegia patients. METHODS: Twenty-four hemiplegic patients were randomly allocated to an experimental group or control group. All participants received 30-min neurodevelopmental treatment. Furthermore, the experimental group received initial contact-emphasized auditory feedback gait training, whereas the control group received gait training without auditory feedback. The intervention was performed 3 times per week, 20 min per each time, for a total of 6 weeks. Balance was assessed using the center of pressure path length, center of pressure velocity, and limitation of stability path length, whereas gait ability was assessed using the 10-m walking test and functional gait assessment. RESULTS: In both groups, center of pressure path length and center of pressure velocity significantly decreased after training. Compared to the control group, the experimental group showed a 10% significant improvement (p<.05). In the limitation of stability path length of both sides, the experimental group showed a significant increase compared to that before intervention. Compared to the control group, the experimental group showed a 7% significant improvement in results of the 10-m walking test and functional gait assessment (p<.05). CONCLUSION: Emphasized Initial contact gait training is considered an effective treatment for improving gait ability and balance ability in stroke patients.

• Journal of the Korean Vacuum Society
• /
• v.7 no.2
• /
• pp.118-126
• /
• 1998

A study to improve filling of semiconductor contact holes by enhancement of the directionality of the source beams has been undertaken. The collimation of source beams was improved by the ionized cluster beam deposition technique with modification of the cell geometry. The collimation tested with neutral beam was excellent. But, the Cu flims were grown in a columnar mode due to the lack of surface mobilit of the impinged clusters. A shadow effect also caused cleavage and consequent discontinuity at the steos as films grow. By applying acceleration voltage, the columnar growth in a contact hole of 0.5 $\mu$m diameter and 1 $\mu$m height disappeared and considerable coverage at the side wall of the contacts as well as perfect bottom coverage were observed. These are all due to the assistants of the accelerated ionized clusters with high kinetic energy. Thus we demonstrated that the ICB deposition technique can be used to completely fill sub-half-micron contact holes with high aspect ratio.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.55-55
• /
• 2018

Recently, amorphous oxides such as InGaZnO (IGZO) and InZnO (IZO) as a channel layer of an oxide TFT have been attracted by advantages such as high mobility, good uniformity, and high transparency. In order to apply such an amorphous oxide TFTs to a display, the stability in various environments must be ensured. In the InGaZnO which has been studied in the past, Ga elements act as a suppressor of oxygen vacancy and result in a decreased mobility at the same time. Previous studies have been showed that the InZnO, which does not contain Ga, can achieve high mobility, but has relatively poor stability under various instability environments. In this study, the TFTs using $IZO/Al_2O_3$ double layer structure were studied. The introduction of an $Al_2O_3$ interlayer between source/drain and channel causes superior electrical characteristics and electrical stability as well as reduced contact resistance with optimally perfect ohmic contact. For the IZO and $Al_2O_3$ bilayer structures, the IZO 30nm IZO channels were prepared at $Ar:O_2=30:1$ by sputtering and the $Al_2O_3$ interlayer were depostied with various thickness by ALD at $150^{\circ}C$. The optimal sample exhibits considerably good TFT performance with $V_{th}$ of -3.3V and field effect mobility of $19.25cm^2/Vs$, and reduced $V_{th}$ shift under positive bias stress stability, compared to conventional IZO TFT. The enhanced TFT performances are closely related to the nice ohmic contact properties coming from the defect passivation of the IZO surface inducing charge traps, and we will provide the detail mechanism and model via electrical analysis and transmission line method.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.1
• /
• pp.34-41
• /
• 2018

A flange joint is a pipe connection used to prevent the leakage of high-pressure fluids by inserting a gasket and tightening the bolts. Among several kinds of gaskets available, metal ring type joint gaskets are most widely used in conditions that require high-temperature and high-pressure fluid flow, such as oil pipelines, gas pipes, pumps, valve joints, etc. The purpose of this study is to investigate the contact pressure and stress characteristics closely related to the sealing performance of Class 900 flange joints used in high temperature and high pressure environments. The dimensions of flange joints with five different nominal pipe sizes were determined with reference to those specified in ASME 16.5. The metal ring gaskets inserted in the joints were octagonal and oval gaskets. The bolt tensile forces calculated from the tightening torques were input as the bolt pretension loads in order to determine the contact pressure and stress levels after fastening. Loading was composed of three steps, including the fastening step, and different amounts of applied pressures were used in each analysis to investigate the effect of fluid pressure on the contact force of the joints. A general-purpose software, ANSYS 17.2, was used for the analysis.

• Journal of Convergence for Information Technology
• /
• v.10 no.11
• /
• pp.87-97
• /
• 2020

The purpose of this study was to investigate effect of simulation based education using standardized patient for contact precaution infection control for nursing student. This study was conducted by including 67 nursing student A university from October to December 2019. This study was mixed method research design. Knowledge and performance confidence related to multidrug resistant organism(MDRO) infection control were measured using questionnaires pre and post test, analyzed using paired t-test and reflection sheet was analyzed using content analysis method. After intervention, two variables were increased significantly. Results of the content analysis showed there were 39 significant statements, which were classified into 13 categories. These results suggest that education on simulation program using standardized patient for contact precaution infection control is effective strategy to enhance knowledge and performance confidence related to MDRO infection control and practical nursing infection control skill, patient centered care, interprofessional collaboration.

• The Journal of Advanced Prosthodontics
• /
• v.12 no.2
• /
• pp.75-82
• /
• 2020

PURPOSE. The aim of this study was to investigate the shear bond strength of luting cements used with implant retained restorations on to titanium specimens after different surface treatments. MATERIALS AND METHODS. One hundred twenty disc shaped specimens were used. They were divided into three groups considering the surface treatments (no treatment, sandblasting, and oxygen plasma treatment). Water contact angle of specimens were determined. The specimens were further divided into four subgroups (n=10) according to applied cement types: polycarboxylate cement (Adhesor Carbofine-AC), temporary zinc oxide free cement (Temporary CementZOC), non eugenol provisional cement for implant retained prosthesis (Premier Implant Cement-PI), and non eugenol acrylic-urethane polymer based provisional cement for implant luting (Cem Implant Cement-CI). Shear bond strength values were evaluated. Two-way ANOVA test and Regression analysis were used to statistical analyze the results. RESULTS. Overall shear bond strength values of luting cements defined in sandblasting groups were considerably higher than other surfaces (P<.05). The cements can be ranked as AC > CI > PI > ZOC according to shear bond strength values for all surface treatment groups (P<.05). Water contact angles of surface treatments (control, sandblasting, and plasma treatment group) were 76.17° ± 3.99, 110.45° ± 1.41, and 73.80° ± 4.79, respectively. Regression analysis revealed that correlation between the contact angle of different surfaces and shear bond strength was not strong (P>.05). CONCLUSION. The retentive strength findings of all luting cements were higher in sandblasting and oxygen plasma groups than in control groups. Oxygen plasma treatment can improve the adhesion ability of titanium surfaces without any mechanical damage to titanium structure.

• Advances in environmental research
• /
• v.5 no.3
• /
• pp.189-200
• /
• 2016

This study aimed at advanced oxidation of hetero tri-functional reactive dye Acid orange 7 using photo-Fenton conditions in a lab-scale experiment. Decolourisation of Acid Orange 7 dye by Fenton's process was dependent on concentration of Hydrogen peroxide, Ferrous sulphate, pH, and contact time. A $2^3$ factorial design was used to evaluate the effects of these key factors: pH, Fe(II), and $H_2O_2$ concentration, for a dye concentration of 50 mg/L with COD of 340 mg/L at pH 3.0. The response function was removal of colour under optimised conditions; pH 3.0, [Fe(II)] 40.83 mg/L, [$H_2O_2$] 4.97 mmol/L; 13.6 min. of treatment resulting in 100% colour removal. The final COD of treated wastewater was nil suggesting that AOP is a potentially useful process of color removal and dye degradation/mineralisation of effluent having AO7. Minimum contact time for complete decolourisation was at 5 mmol/l $H_2O_2$ concentration. Increase in $FeSO_4$ (mg/l) concentration resulted in decrease of time for complete decolourisation. Box-Behnken Design was used to optimize the process variables. Maximum and minimum levels of pH (3-5), $H_2O_2$ (4-6 mmol/l), $FeSO_4$ (30-46 mg/l) and contact time (5-15 minutes) were used. The statistical analysis revealed a value of 0.88 for coefficient of regression ($R^2$) indicating a good fit of model. Calculated F-value was found higher than the tabulated value confirming to significance of the model. Based on student's t-test, Ferrous sulphate, pH, and contact time have a positive effect on the percent decolourisation of Acid Orange 7.