• Solar Energy
• /
• v.17 no.4
• /
• pp.3-11
• /
• 1997

Because grain boundaries in polycrystalline silicon act as potential barriers and recombination centers for the photo-generated charge carriers, these defects degrade conversion effiency of solar cell. To reduce these effects of grain boundaries, we investigated various influencing factors such as thermal treatment, various grid pattern, selective wet etching for grain boundaries, buried contact metallization along grain boundaries, grid on metallic thin film. Pretreatment above $900^{\circ}C$ in $N_2$ atmosphere, gettering by $POCl_3$ and Al treatment for back surface field contributed to obtain a high quality poly-Si. To prevent carrier losses at the grain boundaries, we carried out surface treatment using Schimmel etchant. This etchant delineated grain boundaries of $10{\mu}m$ depth as well as surface texturing effect. A metal AI diffusion into grain boundaries on rear side reduced back surface recombination effects at grain boundaries. A combination of fine grid with finger spacing of 0.4mm and buried electrode along grain boundaries improved short circuit current density of solar cell. A ultra-thin Chromium layer of 20nm with transmittance of 80% reduced series resistance. This paper focused on the grain boundary effect for terrestrial applications of solar cells with low cost, large area, and high efficiency.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.9-15
• /
• 2007

In this paper, we present the design of Schottky diodes and voltage multiplier for UHF-band passive RFID applications. The Schottky diodes were fabricated using Titanium (Ti/Al/Ta/Al)-Silicon (n-type) junction in $0.35\;{\mu}m$ CMOS process. The Schottky diode having $4{\times}10{\times}10\;{\mu}m^{2}$ contact area showed a turn-on voltage of about 150 mV for the forward diode current of $20\;{\mu}A$. The breakdown voltage is about -9 V, which provides sufficient peak inverse voltage necessary for the voltage multiplier in the RFID tag chip. The effect of the size of Schottky diode on the turn-on voltage and the input impedance at 900 MHz was investigated using small-signal equivalent model. Also, the effect or qualify factor of the diode on the input voltage to the tag chip is examined, which indicates that high qualify factor Schottky diode is desirable to minimize loss. The fabricated voltage multiplier resulted in a output voltage of more than 1.3 V for the input RF signal of 200mV, which is suitable for long-range RFID applications.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.3
• /
• pp.83-90
• /
• 2020

The effect of substrate surface roughness and sintering temperature on the adhesion strength of Ag-based thick film conductors formed on AlN substrates with excellent thermal conductivity was studied. The adhesion strength of the thick-film conductor manufactured using an AlN substrate having a surface roughness (R_a) of 0.5 was higher than that of a thick-film conductor manufactured using a substrate having a surface roughness greater or smaller than this. In the case of a substrate with a surface roughness of less than 0.5, the contact area between the Ag thick film conductor and the substrate was relatively smaller than that of a substrate with a surface roughness of 0.5, resulting in a lower adhesive strength. On the other hand, when a substrate having a surface roughness of more than 0.5 was used, it was found that the conductor film was not completely adhered to the substrate, and as a result, it was found that the adhesive strength was small. In addition, it was found that the surface smoothness of the Ag-based thick film conductor film obtained by sintering at 850℃ was the best compared to the smoothness of the conductor film obtained by sintering at different sintering temperatures, and as a result, it was found that the adhesive strength of the conductor film was the highest.

• Management & Information Systems Review
• /
• v.30 no.4
• /
• pp.45-71
• /
• 2011

This study aims at reviewing the effect of the non-verbal communication of salespersons at service encounter on customers' non-verbal communication and responses. The previous studies overlooked the correlation between salespersons' non-verbal communication and customers' non-verbal communication at service encounter, although non-verbal communication of salespersons has potentialities evoking customers' non-verbal communication and emotional responses in various ways. If it is a salesperson who a customer first encounters within a shop, the non-verbal communication of salesperson affects his/her non-verbal communication and these non-verbal communication affect his/her emotional responses, and these emotional responses affect his/her behavior. This phenomenon is based on the theory of emotional contagion, mimic, and face feedback. Therefore the non-verbal communication such as greetings, postures and eye-contact manners through the personal interactions between salespersons and customers, can be said to be an antecedent variable which affects the positive responses of customer. As a result of the study, the kinesic of salesperson's non-verbal communication was found to affect customers' non-verbal communication, and customers' non-verbal communication affect emotional responses experienced at service encounter, and customers' positive emotion affect customers' behavior responses. This result provides an opportunity which makes one turn eyes on salespersons' non-verbal communication at sales encounter both practically and scientifically, through introducing salespersons' non-verbal communication as an important factor which can enhance customers' positive responses but has been passed over by the previous studies.

• Journal of Periodontal and Implant Science
• /
• v.37 no.4
• /
• pp.791-803
• /
• 2007

The purpose of this study was to evaluate exophytically vertical bone formation in residual ridge of the beagle dog by the concept of guided bone regeneration with a titanium reinforced e-PTFE membrane combined with irradiated cancellous human bone. Twelve male beagle dogs(mean age 1.5 years and mean weight 12kg) were used for this study. The alveolar ridges after extraction of all mandibular premolars were surgically and horizontally removed. At 8 weeks after extractions, full-thickness flap was reflected and cortical bone was removed with round bur and copious irrigation. Rectangular parallelepiped(10mm in length, 5mm in width, and 4mm in height) bended with titanium-reinforced e-PTFE(TR e-PTFE) membrane was placed on the decorticated alveolar ridge, fixed with metal pins and covered with full-thickness flap and assigned as a control group. Test groups ere treated with TR e-PTFE membrane filled with irradiated cancellous human bone. Of twelve beagle dogs, four control dogs and four test dogs without membrane exposure to oral cavity were sacrificed at 8 and 16 weeks respectively. The surgical sites were dissected out, fixed in 4% buffered formaldehyde, dyed using a Villanueva staining technique, and processed for embedding in plastic resin. The cutting and grinding methods were routinely processed for histologic and histomophometric analyis of exophytic bone formation as well as statistical analysis. The results of this study were as follows: 1. Exophytic bone formation in the both of experimental groups was increased respectively after surgery from 23.40% at 8 weeks to 46.26% at 16 weeks in the control groups, from 40.23% at 8 weeks to 47.11% at 16 weeks in the test groups(p<0.05). 2. At 8 weeks after surgery, exophytic bone formation was made 40.23% in the test groups and 33.40% in the control groups. Exophytic bone formation was significantly made in the test group more than in the control group. At 16 weeks after surgery, exophytic bone formation was made 44.11% in the test groups and 46.26% in the control groups. Exophytic bone formation was made in the test groups more than in the control groups, but there was no statistically significant differences. 3. The membrane was fixed with metal pins to closely contact it to the bone surface. So, collapse and deviation of the membrane could be prevented and in growth of connective tissue also could be blocked from the periphery of the membrane. On the basis of these findings, wee suggest that intraoral experimental model for exophytic bone formation may be effective to evaluate the effect of bone graft material. And it indicates that combined use of membrane and ICB graft material is more effective than use of membrane only for exophytic bone formation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.30 no.4
• /
• pp.541-564
• /
• 1992

The purpose of this experiment was to study the effect of implantation of the dense hydroxyapatite (HA) granules$(Apaceram^{(R)})$ in the fresh extraction sockets on the residual ridge resorption in normal and induced diabetic rabbits. Sixty-four white rabbits, weighing 3.0kg, were utilized in this study and they were divided into four group : group 1-sixteen normal rabbits without filling HA granules, group 2-sixteen normal rabbits with filling HA granules, group 3-sixteen diabetic rabbits without filling HA granules, group 4-sixteen diabetic rabbits with filling HA granules. HA granules were filled immediately after extraction in the extraction sockets of the mandibular left 1st, 2nd, and 3rd molar in group 2 and 4, and no HA granules were filled in group 1 and 3. The calculation of residual ridge resoption was done at 4th week, 8th week, 12th week, and 16th week after surgery, and histologic examination was performed to study healing process at 2nd week, 4th week, 8th week, and 16th week after surgery. The results were as follows : 1. The amount of residual ridge resorption was largest in group 3, and smallest in group 2 in every interval. There was no statistically significant difference between group 1 and 4. 2. In all groups, the amount of residual ridge resorption was high until 4th week after surgery, but the rate of residual ridge resolution slowly decreased after 4th week 3. There was more active healing process in group 1 and 2 than in group 2 and 4. 4. According to filling of HA granules, there was no difference in the amount of new bone formation, but direct contact could be observed between newly formed bone and HA granules in group 2 and 4. 5. Group 1 and 3 showed marked bone resorption and adipose marrow from 8th-16th week after surgery, but group 2 and 4 did not show maeked bone resolution, and showed fibrous tissue and a little adipose tissue among trabeculae from 8th week.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.4
• /
• pp.187-192
• /
• 2007

Impact on cylindrical surface caused by plunging breaking waves is investigated experimentally. The breaking waves are generated in a wave flume by decreasing the wave maker frequencies linearly and focusing the generated wave components at one specific location. The breaking wave packets are based on constant wave steepness spectrum. Three inclination angles of cylinder are applied to examine the effect of contact angle between cylinder and front surface of breaking waves. Also, the effect of cylinder diameter on pressure distribution and its peak value is investigated by adopting three cylinders with different diameters. The longitudinal location of cylinder is slightly moved in eight different points to find out a probable maximum value of impact pressure. The pressures and total force on cylinder surface are measured by piezo-electric pressure sensors and 3-components load cell with 30kHz sampling rate. The variation of peak impact pressures and forces is analyzed in terms of cylinder diameter, inclination angle and location. Also, the pressure distribution on cylindrical surface is examined. The cylinder location and surface position are more important parameters that govern the magnitude and shape of peak pressures, while the cylinder diameter and inclined angle are relatively insignificant. In a certain conditions, the impact phenomenon becomes very unstable which results in a large variation of measured valves in repeated runs.

• Journal of the Korean Society of Safety
• /
• v.26 no.4
• /
• pp.47-58
• /
• 2011

Halogen free intumescent flame retardants(IFRS), such as the mixture of melamine phosphate(MP) and char forming agents(pentaerythritol(PER), di-pentaerythritol(DiPER), tris(2-hydroxyethyl) isocyanurate(THEIC)), were prepared and characterized. Polypropylene(PP)/$IFR_S$ composites were also prepared in the presence of ethylene diamine phosphate(EDAP) as a synergist and used into flame retardant PP powder coatings. Thermoplastic PP powder coatings at 20 wt% flame retardant loading were manufactured by extruded and then mechanical cryogenic crushed to bring them in fine powder form. These intumescent flame retardant powder coatings($IFRPC_S$) were applied on mild steel surface for the purpose of protection and decorative. It is a process in which a $IFRPC_S$ particles coming in contact with the preheated mild steel surface melt and form a thin coating layer. The obtained MP flame retardant was analyzed by utilizing FTIR, solid-state $^{31}P$ NMR, ICP, EA and PSA. The mechanical properties as tensile strength, melt flow index(MFI) and the thermal property as TGA/DTA and the fire safety characteristics as limiting oxygen index(LOI), UL94 test, SEM were used to investigate the effect of $IFRPC_S$. The experimental results show that the presence of $IFR_S$ considerably enhanced the fire retardant performances as evidenced by the increase of LOI values 17.3 vol% and 32.6 vol% for original PP and $IFRPC_S$-3(PP/MP-DiPER/EDAP), respectively, and a reduction in total flaming combustion time(under 15 sec) in UL94 test of $IFRPC_S$. The prepared $IFRPC_S$-3 have good comprehensive properties with fire retardancy 3.2 mm UL94 V-0 level, LOI value 32.6%, tensile strength $247.3kg/cm^2$, surface roughness Ra $0.78{\mu}m$, showing a better application prospect. Through $IFRPC_S$-2(PP/MP-PER/EDAP) and $IFRPC_S$-3 a better flame retardancy than that of the $IFRPC_S$-1(PP/MP/EDAP) was investigated which was responsible for the formed more dense and compact char layer, improved synergy effect of MP and PER/DiPER.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.3370-3377
• /
• 2015

FMECA(Failure Mode, Effects and Criticality Analysis) techniques to make quantitative evaluation of failure effects severity and criticality have been applied to systematic failure analysis for reliability improvement of train which should provide regular service and secure high level of safety as a mass transportation system. These FMECA techniques do not fully reflect the inherent train operation and maintenance circumstances because they are based on the FMECA standards devised for other industries such as automobile industry and FMECA standard dedicated to train industry has not been established yet. This paper analyzes FMECA standards for various industries, and suggests a FMECA technique dedicated to train industry which makes failure effect analysis and criticality analysis step by step and makes criticality analysis placing emphasis on the severity of the failure effect. The proposed technique is applied to FMECA of high-speed current breaker which is a core safety device of train using field failure data for 15 years of train maintenance. The FMECA results show that breakage of arc chute has the highest risk with 3rd severity class and 5th criticality class among all the components of high-speed circuit breaker. Damage and poor contact of electronic valve, and cylinder breakage with 3rd severity class and 4th criticality class are followed by. These results can be applied to improvement of design and maintenance process for high-speed circuit breaker of train.

• Restorative Dentistry and Endodontics
• /
• v.42 no.3
• /
• pp.206-215
• /
• 2017

Objectives: To determine the combined effect of fatigue cyclic loading and thermocycling (CLTC) on the shear bond strength (SBS) of a resin cement to zirconia surfaces that were previously air-abraded with aluminum oxide ($Al_2O_3$) particles at different pressures. Materials and Methods: Seventy-two cuboid zirconia specimens were prepared and randomly assigned to 3 groups according to the air-abrasion pressures (1, 2, and 2.8 bar), and each group was further divided into 2 groups depending on aging parameters (n = 12). Panavia F 2.0 was placed on pre-conditioned zirconia surfaces, and SBS testing was performed either after 24 hours or 10,000 fatigue cycles (cyclic loading) and 5,000 thermocycles. Non-contact profilometry was used to measure surface roughness. Failure modes were evaluated under optical and scanning electron microscopy. The data were analyzed using 2-way analysis of variance and ${\chi}^2$ tests (${\alpha}=0.05$). Results: The 2.8 bar group showed significantly higher surface roughness compared to the 1 bar group (p < 0.05). The interaction between pressure and time/cycling was not significant on SBS, and pressure did not have a significant effect either. SBS was significantly higher (p = 0.006) for 24 hours storage compared to CLTC. The 2 bar-CLTC group presented significantly higher percentage of pre-test failure during fatigue compared to the other groups. Mixed-failure mode was more frequent than adhesive failure. Conclusions: CLTC significantly decreased the SBS values regardless of the air-abrasion pressure used.