• Journal of the Korea Institute of Building Construction
• /
• v.1 no.2
• /
• pp.146-153
• /
• 2001

Radical development has been made in the every field of our society for the past scores of year. Radical development of industry and lining environment has mass-produced various toxic wastes . Which comes to the fore as a serious environmental problem. The purpose of this is to suggest the optima mix design by studying the utility of a toxic waste, plated sludge as a building material and deciding the standards of quality and use of cement and evaluating the properties of mortar and concrete in which plated sludge mixed. From an experiment, compressive strength required high early strength cement or special cement. Watertightness proved to be excellent. Heavy metals, such as Cd, Pb, Cu came out below an environmental standard. Cr+6 exceeded an environmental standard under a steam curing, but came out below an environmental under a standard curing. The higher replacement rate was, the lower frost, fusion and resistance were. Thus, got better results above the goal by condition. It was possible that plated sludge was replaced and solidified to aggregate. Therefore, it is necessary to define the standards of quality on strength, replacement rate of wastes, water permeability, endurance in other to solidify plated sludge to concrete products.

• Advances in concrete construction
• /
• v.6 no.1
• /
• pp.47-68
• /
• 2018

This article reports the utilization of fly ash (FA) waste product from industry and silpozz which is an agro-waste from agriculture as an environmental friendly material in construction industry. The evaluation of strength and durability study was observed using FA and silpozz as a partial replacement of Ordinary Portland Cement (OPC). The studied parameters are compressive strength, flexural strength, split tensile strength and bond strength as well as the durability study involves the acid soluble chloride (ASC), water soluble chloride (WSC), water absorption and sorptivity. Scanning electron microscopy (SEM) and XRD of selected samples are also done. It reveals from the test results that the deterioration factor (DF) in compressive strength is 4% at 365 days. The DF of split tensile strength and flexural strength is 0.96% and 0.6% at 90 days respectively. The minimum slip is 1mm and 1.1mm after 28 days of testing bond strength for NWC and SWC sample respectively. The percentage decrease in bond strength is 10.35% for 28 days SWC samples. The pre-cast blended concrete samples performed better to chloride diffusion. Modulus of elasticity of SWC samples are also studied.The water absorption and sorptivity tests are conducted after 28 days of curing.

• Advances in concrete construction
• /
• v.9 no.4
• /
• pp.345-354
• /
• 2020

Cement is the most significant component in concrete. Large scale manufacturing of cement consumes more energy and release harmful products (Carbon dioxide) into the atmosphere that adversely affect the environment and depletes the natural resources. A lot of research is going on in globally concentrating on the recycling and reuse of waste materials from many industries. A major share of research is focused on finding cementitious materials alternatives to ordinary Portland cement. Many industrial waste by-products such as quartz powder, metakaolin, ground granulated blast furnace slag, silica fume, and fly ash etc. are under investigations for replacement of cement in concrete to minimize greenhouse gases and improve the sustainable construction. In current research, the effects of a new generation, ultra-fine material i.e., alccofine which is obtained from ground granulated blast furnace slag are studied as partial replacement by 25% and with varying amounts of sulfonated naphthalene formaldehyde (i.e., 0.3%, 0.35% and 0.40%) on mechanical, water absorption, thermal and microstructural properties of concrete. The results showed moderate improvement in all concrete properties. Addition of SNF with combination of alccofine showed a significant enhancement in fresh, hardened properties and water absorption test as well as thermal and microstructural properties of concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.143-144
• /
• 2019

Recently, environmental pollution related to global warming is on the rise. Meanwhile, renewable energy is a representative example of many efforts to develop eco-friendly energy to solve the depletion of natural resources and the depletion of petroleum resources in conjunction with global warming. Among them, photovoltaic power generation is increasing the subsidies for the government to increase the production of photovoltaic electricity of the general public, showing a high growth rate. However, polysilicon, which is a raw material of the photovoltaic panel, generates waste called polysilicon sludge in the manufacturing process. In order to produce 1 ton of polysilicon, about 2 tons of waste polysilicon sludge is generated. In 2012, polysilicon sludge was generated at 78,000 tons, with an average of about 220 tons per day. The sludge generated due to insufficient treatment of polysilicon sludge is currently solidified and is processed by landfilling. Therefore, in this study, polysilicone sludge is used as the concept of admixture, and the physical properties of the matrix according to the polysilicon sludge replacement ratio based on light burned magnesia is determined.

• Journal of the Korean Geosynthetics Society
• /
• v.11 no.3
• /
• pp.19-25
• /
• 2012

In this study, a recycling plan for waste concrete fine aggregate as fill material was researched by investigating environmental engineering properties. It is noted that the environmental influence of waste concrete fine aggregate is little since chemical level is satisfied the waste management standard. Waste concrete fine aggregate is not suitable for materials of anti-frost layer and sub-base layer since the particle-size distribution and engineering properties are not partially satisfied the quality standard. However, waste concrete fine aggregate can be recycled as materials of anti-frost layer and sub-base layer if we improve the engineering properties by mixing bigger aggregates than maximum particle size (5 mm) more than 25 percent of total weight.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.6
• /
• pp.457-462
• /
• 2010

Sound absorption capability and bending strength of laminated ship-building plywood waste of maple and melanti wood were estimated. Sound absorption coefficients of wood had been measured by the two microphone transfer function method and bending strength examined by three point loading. The maximum strength in bending of laminated ship-building plywood waste of maple and melanti wood were 534 and 414 kgf/$cm^2$, respectively. The sound absorption coefficients of laminated ship-building plywood waste were higher than mongolian oak and fiber board, well used construction material. Especially, in the case of laminated ship-building plywood waste of melanti wood, average sound absorption coefficient was about 0.25. It was surmised that the laminated ship-building plywood waste can be used as interior materials because of its good mechanical and sound absorption properties.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.1
• /
• pp.29-36
• /
• 2009

Recycling of wood wastes or residues is a good solution for a shortage of wood resources and a rise in the price. Shipbuilding wood wastes were almost used to produce the boards by milling. However, considering the economic value and insufficient resource, recycling with milling is dissatisfied method. This study has been carried out to investigate the recycling possibility of shipbuilding wood waste. There are two kinds of shipbuilding wastes: plywood waste and solid waste. From the results of this study, the following conclusions have been made: 1. Bending properties of plywood and laminated plywood lumber were tested by Korean Standard. 2. The main fracture mode of plywood waste and laminated plywood lumber is that of simple tension. 3. The recommended application for the recycling of shipbuilding wood waste are outdoor wood furnishings, indoor wood furnishings and some wooden building construction materials: interior raw material, wooden pallet, siding, paneling, flooring. picnic table, deck components, porch swing, landscaping timbers, residential fencing, patios, and boardwalks etc.

• Advances in materials Research
• /
• v.13 no.2
• /
• pp.115-128
• /
• 2024

Concrete is the most significant material in the construction industry which is required to construct several facilities like roads, buildings, and bridges etc. which leads to the economic development of a country. But now days, in view of sustainable development and environmental problems, plastic waste management is one of the major environmental issues due to its non-biodegradable nature which allows it to stay in the landfills until they are cleaned up. To overcome all these concerns, plastic waste may be used as a substitute of natural fine and coarse aggregate in concrete and a valuable solution to utilize the plastic items which causes several problems. In order to, present study is focused on the affecting properties of concrete as workability, compressive strength, and tensile strength of concrete with using plastic waste and without using plastic waste. Based on the detailed literature, it was observed that the plastic waste is not affecting the quality and consistency of concrete. However, as the number of PVC particles in the mixture increased, the drying shrinkage values decreased and the inclusion of plastic flakes can mitigate drying shrinkage cracking which leads the higher durability of concrete. Based on the comprehensive literature, it was also observed that the plastic aggregate found to be suitable for low and medium strength concrete. However, the investigation on the application of plastic aggregate in the high strength concrete is found limited. It was concluded that the optimum percentage of the plastic aggregate was found about 20%.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.39 no.5
• /
• pp.119-126
• /
• 2011

The standard unit manpower and material in landscape architectural construction was consist of a standard and universal work classification. However, these constructional methods have created a number of problems in utilizing and responding on a variety of recently-developed working methods such as new constructional skills and technologies. This research decided that presenting the amendments of work classification of a standard unit manpower and material in landscape architectural construction was very important, and investigated those work classifications which required these new amendments. First of all, assessment items were selected through the literature reviews and a preliminary survey. Then, these assessment items were surveyed to the total of 60 professional landscape architecture field. The results of this study were as follows; First, the utilization level of the a standard unit manpower and material in landscape architectural construction was highest in the area of work classification of planting unit manpower and material. Second, the work classifications that needed to be added were recognized as leveling the ground construction, landscape structure construction, paving construction, water facilities construction, and outdoor facilities construction. Third, in the field of the a standard unit manpower and material in landscape architectural construction, 66.7% of the respondents replied that some amendments were necessary, and those amendments needed work classifications were identified as work classification of planting unit manpower and material was gigantic plant, topiary tree, temporary planting, exchange dead tree, etc. In the area of digging out was gigantic plant and plastic tree were recognized. The survey respondents also answered that, in keeping and management work classifications some amendments in pruning waste were necessary, and in the fields of rubble masonry work classifications some improvements were required in rubble aperture planting unit manpower and material and sodding and herbaceous sowing was a realistic lawn size unit manpower and material was needed. Based on the results explained above, this study suggests that amendments for a standard unit manpower and material in landscape architectural construction are necessary, especially in the areas of planting size and quality of work classifications unit manpower and material and in the unit manpower and material that affects the quality of lands caping constructions.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.281-286
• /
• 2001

The development of automobile, vessel, rail road, and machine industry leads increase of foundry production used as their components, which cause a by-product, waste foundry sand (WFS). The amount of the WFS produced in Korea is over 900,000 ton a year, but most WFS buries itself and only 5~6% WFS is recycled as a material in construction materials. In this study, WFS is used as a fine aggregate for concrete. Five types of concretes aimed at the specified strength of 240$\pm$10 kgf/$cm^{2}$ , air contents of 4.5$\pm$1% and slump of 12$\pm$1.5cm were mixed with washed coarse seashore sand(WFS) in which salt was removed and then optimum mix proportion of concrete was determined. Moreover, basic properties such as setting time, workability, bleeding and slump loss of the fresh concrete with WFS were tested and compared with those of the concrete mixed without WFS. In .addition, both compressive strength of hardened concrete at each ages and tensile strength of it at the age of 28 days were measured and discussed.