• Journal of the Korean Institute of Gas
• /
• v.6 no.4 s.18
• /
• pp.1-7
• /
• 2002

Human errors can take place in all levels that include the design, production, construction, operation and maintenance of plant facilities. It was found that the causes were concerned with the effects of human error. This study verified characteristics of the on-site operators and error mechanism, and used the classifying sheet to analyze human error that occurred in process. Also, by applying the ASEP(Accident Sequence Evaluation Program) HRA(Human Reliability Analysis) procedure, the algorithm to estimate the HEP and the ASEP HEP program to analyze human error in the plant were developed. If it is built in on-site, possible human error incident will be prevented and the systematic human error prevention strategy will be devised.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.3
• /
• pp.307-321
• /
• 2015

The primary objective of this study is to investigate the feasibility of an innovative surface-mount sensor, made of a piezoelectric disc (PZT sensor), as a consistent source for surface wave velocity and transmission measurements in concrete structures. To this end, one concrete slab with lateral dimensions of 1500 by 1500 mm and a thickness of 200 mm was prepared in the laboratory. The concrete slab had a notch-type, surface-breaking crack at its center, with depths increasing from 0 to 100 mm at stepwise intervals of 10 mm. A PZT sensor was attached to the concrete surface and used to generate incident surface waves for surface wave measurements. Two accelerometers were used to measure the surface waves. Signals generated by the PZT sensors show a broad bandwidth with a center frequency around 40 kHz, and very good signal consistency in the frequency range from 0 to 100 kHz. Furthermore, repeatability of the surface wave velocity and transmission measurements is significantly improved compared to that obtained using manual impact sources. In addition, the PZT sensors are demonstrated to be effective for monitoring an actual surface-breaking crack in a concrete beam specimen subjected to various external loadings (compressive and flexural loading with stepwise increases). The findings in this study demonstrate that the surface mount sensor has great potential as a consistent source for surface wave velocity and transmission measurements for automated health monitoring of concrete structures.

• Journal of the Korean Society of Safety
• /
• v.31 no.1
• /
• pp.48-53
• /
• 2016

This paper deals with analysis of complex grounding system using electromagnetic simulation method. Electrical devices could be damaged by transient voltage such as a lightning surge. Therefore the measures to protect the equipments from transient, such as a lightning are required. The ground system is important in this respect. The representative parameter of grounding system performance is earth ground resistance. Precise prediction of earth resistance is required, because it is difficult to modify and change after the completion of the grounding system construction. Numerical modeling is often used in numerical analysis to identify the electrical characteristics of the grounding system. However complex systems are difficult to predict grounding characteristics by numerical analysis. If the total electric field of the earth in general is similar to the antenna model, in that the incident electric field and expressed as a sum of the scattering field. In this study, the electromagnetic field simulation tool "ANSYS HFSS" module containing the antenna model was used to analyze performance of ground system. Both the simple and complex grounding system were analyzed by simulation tool and experimental method. As a result simulation method is effective to predict performance of a complex ground system.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.6
• /
• pp.484-497
• /
• 2016

In order to understand the characteristics of the topography change in front of an impermeable breakwater, a coupled model for a two-way analysis of the existing LES-WASS-2D and newly developed morphodynamic model was suggested. A comparison to existing experimental results revealed that the results computed using the 2-D hydro-morphodynamic model were in good agreement with the experimental results for the wave form, pore water pressure in the seabed, and topographical change in front of a submerged breakwater. It was shown that the two-way model suggested in this study is applicable to a morphological change in the seabed around a submerged breakwater. Then, using the numerical results, the topographical changes in front of an impermeable submerged breakwater were examined in relation to partial standing waves. Moreover, the characteristics of the local scour depths in front of them are also discussed in relation to incident wave conditions, sediment qualities, and submerged breakwater shapes.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.65-67
• /
• 1996

This paper presents the automatic construction and parameter optimization technique for the fuzzy logic controller using genetic algorithm. In general the design of fuzzy controller has difficulties in the acquisition of expert's knowledge and relies to a great extent on empirical and heuristic knowledge which, in many cases, cannot be objectively justified. Therefor the performance of the controller can be degraded in the case of plant parameter variations or unpredictable incident which the designer may lave ignored. And fuzzy logic controller parameters elicited form the expert may not be global. Some of these problems can be resolved by application of genetic algorithm. Finally, we provides the second order dead time plant to evaluate the feasibility and generality of our proposed method. Comparison shows that the proposed method can produce a fuzzy logic controller with higher accuracy and a smaller number of fuzzy roles than manually billed fuzzy logic controller.

• Journal of Navigation and Port Research
• /
• v.41 no.5
• /
• pp.345-352
• /
• 2017

Recently, a new port reserves deep water depth for safe navigation and mooring, following the trend of larger ship building. Larger port facilities include long and huge breakwaters, and mainly adopt vertical type considering low construction cost. A vertical breakwater creates stem waves combining inclined incident waves and reflected waves, and this causes maneuvering difficulty to the passing vessels, and erosion of shoreline with additional damages to berthing facilities. Thus, in this study, the researchers have investigated the response of stem waves at the vertical breakwater near the entrance channel and applied numerical models, which are commonly used for the analysis of wave response at the harbor design. The basic equation composing models here adopted both the linear parabolic approximation adding the nonlinear dispersion relationship and nonlinear parabolic approximation adding a linear dispersion relationship. To analyze the applicability of both models, the research compared the numerical results with the existing hydraulic model results. The gap of serial breakwaters and aligned angles caused more complicated stem wave generation and secondary stem wave was found through the breakwater gap. Those analyzed results should be applied to ship handling simulation studies at the approaching channels, along with the mooring test.

• Journal of Korea Water Resources Association
• /
• v.32 no.6
• /
• pp.675-683
• /
• 1999

The reflection coefficients of monochromatic waves propagating over a shelf with varying dimensions are theoretically calculated. The diffraction of waves by an abrupt depth change is formulated by the eigenfunction expansion method. Not only propagating mode but also evanescent modes are considered in formulation. The role of evanescent modes in reflection coefficients is investigated in detail. Water waves are obliquely as well as normally incident to the region. The obtained reflection coefficients are verified by checking conservation of wave energy.

• Korean Journal of Remote Sensing
• /
• v.25 no.3
• /
• pp.225-231
• /
• 2009

The characteristics of morphological shapes, wave heights, tidal ranges and sediment sizes are observed and compared between intertidal beach and mudflat. The Mohang sand beach, southwest coast of Korea, is located just next to the large mudflat and has tidal range over 5 meters. Wave measurements are conducted at each entrance of the beach and mudflat as well as at the outside waters representing the incident waves to these different coastal environments. The morphological characteristics are also examined including the sediment size and the slope of the bathymetry, For the observation of morphological shapes, camera monitoring technique is used to measure the spatial information of intertidal bathymetry. The water lines moving on the intertidal flat/beach durinq a flood indicate depth contours between low and high water lines. The water lines extracted from the consecutive images are rectified to get the ground coordinates of each depth contours and integrated to provide three dimensional information of intertidal topography. The wave data show that sand beach is in the condition of severer wave forcing but tidal range is almost identical in both environment. The slope of the mudflat is much milder than the sand beach with finer sediment.

• Geophysics and Geophysical Exploration
• /
• v.14 no.1
• /
• pp.25-41
• /
• 2011

AVO analysis was conducted on hydrocarbon-bearing structures by applying the crossplot and offset-coordinate amplitude polynomial techniques. To evaluate the applicability of the AVO analysis, it was conducted on synthetic data that were generated with an anticline model, and field data from the hydrocarbon-bearing Colony Sand bed in Canada. Analysis of synthetic data from the anticline model demonstrates that the crossplot method yields zero-offset reflection amplitude and amplitude variation with negative values for the upper interface of the hydrocarbon-bearing layer. The crossplot values are clustered in the third quadrant. The results of AVO analysis based on the coefficients of the amplitude polynomial are similar to those from the crossplots. These well correlated results of AVO analysis on field and synthetic data suggest that both methods successfully investigate the characteristics of the reflections from the upper interface of a hydrocarbon-bearing layer. Analysis based on the incident-angle equation facilitates the application of various interpretation methods. However, it requires the conversion of seismic data to an incident angle gather. By contrast, analysis using coefficients of the amplitude polynomial is cost-effective because it allows examining amplitude variation with offset without involving the conversion process. However, it warrants further investigation into versatile application. The two different techniques can be complement each other effectively as AVO-analysis tools for the detection of hydrocarbon reservoirs.

• The Korean Journal of Air & Space Law and Policy
• /
• v.19 no.1
• /
• pp.109-139
• /
• 2004

The first successful sustained powered flight by Wright Brothers was further extended to the rapid development of aviation technology, that led to transpacific flights, the invention of supersonic planes, and enabled hundreds of people to travel in the space, in addition to the fact that around 10 people had stepped on the moon, all of which were made possible within the very same century. However, on the back side of this most wondrous human technology, the vulnerableness to the aviation accident has been constantly accompanied with, right from the very beginning stage of the aircraft development. Moreover, the development of future aircraft is being focused on the aircraft performance, the increment of the number of passengers aboard and also its speed. In proportion to these phenomena of mega sizing the aircraft, the development of new technology and the increment of air traffic volume, the number of aviation accident is expected to augment, resulting in the enormous loss of human lives and properties. In order to prevent the disastrous aviation accident as such, it is essential to conduct the accident investigation in a specialized, systematic and scientific manner. In search for the method to attain the effective function of the aviation accident investigation organization, in this study, issues were examined as follows: The full-time Board Members and the establishment of an integrated investigation agency, The systematized security of status as an accident investigator, Inclusion of a human factors specialist in the investigator group organization, liability limit of an accident investigator Stipulation of the definition and the investigation scope of an accident and serious incident, along with the main body of conducting the investigation into the accident involving both civil and public aircraft, in the regulations related to the accident investigation.