• Applied Biological Chemistry
• /
• v.27
• /
• pp.3-17
• /
• 1984

Anaerobic digestion has recently attracted all over the world and Korea also shows no exception. The major benefits of anaerobic digestion are energy production, water pollution control, pathogen reduction and effective manure production. In Korea it was recognized in late sixties that there was a positive need to find alternative energy for farmers household. The main traditional energy sources in rural area were crop residues and forestry products. Therefore Office of Rural Development through its Rural Guidance Bureau disseminated about 29,000 household biogas units from 1969 to 1975 to provide cooking fuel for farmers household and to improve the mode of farmers living standards. The units were welcomed by farmers at that time. Now, however, most of them are not using due to a number of reasons associated with cold winter and some techno-economical problems (in those day, fossil fuel was quite expensive to compare with other prices and since then farmers income was quickly increased). The author studied on bag type household biogas plant to solve some technical problems of existing household biogas plants, but this also has little appeal for the farmers. From 1977 author studied on village scale biogas plant with two pilot plants. From the viewpoint of energy production, COD removal, kill rate of pathogen and fertilizer value, the results obtained from the experiments were quite promising, but the construction cost of the village scale biogas plant was too high for the farmers in Korea. To find most suitable biogas plant for farmers in Korea through the simplifying the biogas digester, the author developed batch-load biogas plant. By feeding coarse crop residues and manures, total solids concentrations of the batch-load biogas plant are about 28 percent which is much higher than continous digester of 5-8 percent. The batch-load biogas plant was welcomed by many farmers in Korea when it was reported on TV and newspapers. The plant was disseminated 154 units in 1982, 766 units in 1983 and 812 units in 1984 as a promissing project. Besides these biogas plant experiments, studies were also conducted 1) to determine gas production rate with agricultural wastes, 2) to evaluate the effect of loading rate, dilution, retention time on biogas production, 3) to project the amount of potencial energy from agricultural wastes.

• Journal of the Korea Concrete Institute
• /
• v.26 no.2
• /
• pp.125-133
• /
• 2014

In this study, experimental research was carried out to investigate the seismic and structural performance of precast concrete exterior beam-column joints using bolt type connection and prestressing method. A total of five full-scale exterior beam-column joints were constructed and tested under reversed cyclic loading, controlled by displacement. Results of the test are as follows: Energy dissipation capacity and pinching phenomenon of PC beam-column joints showed disadvantageous behavior compared to RC beam-column joints. However, drift capacity of the PC joint was excellent. Also, yield mechanism concentrated on embedded nuts was suitable as an exterior beam-column joint of lateral load resistance frame. Additional application of prestressing method was also very effective to control excessive pinching and cracking in the joint region, and thus improved an overall seismic performance of the PC joint.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.11
• /
• pp.33-46
• /
• 2013

Recently, the projects which are to increase the capacity of the flood control are being actively performed because of the abnormal climate changes throughout the country. In this study, the regression analysis was performed using both Kelvin model and the real settlement measured at the crest of the existing concrete face rockfill dam(CFRD) to estimate the long-term deformation behavior characteristics such as creep which occurs without additional load. In addition, the effects on changes in physical properties (E, G, K) of the dam construction materials by deformation characteristics of the dam were evaluated, and the reasonable stability analysis method of the dam was proposed to obtain the long-term stability considering the changes in physical properties induced by the long-term deformation behavior in case of heightening the existing dams.

• Journal of Environmental Science International
• /
• v.20 no.5
• /
• pp.555-564
• /
• 2011

This study examines the potential restoration of abandoned channels of the Mangyeong River in South Korea. To analyze the morphological changes and equilibrium conditions, a flow duration analysis was performed to obtain the discharge of 255 m3/s with a recurrence interval of 1.5 year. It is a gravel-bed stream with a median bed diameter of 36 mm. The reach-averaged results using HEC-RAS showed that the top width is 244 m, the mean flow depth is 1.11 m, the width/depth ratio is very high at 277, the channel velocity is 1.18 m/s, and the Froude number is also high at 0.42. The hydraulic parameters vary in the vicinity of the three sills which control the bed elevation. The total sediment load is 6,500 tons per day and the equivalent sediment concentration is 240 mg/l. The Engelund-Hansen method was closer to the field measurements than any other method. The bed material coarser than 33 mm will not move. The methods of Julien-Wargadalam and Lacey gave an equilibrium channel width of 83 m and 77 m respectively, which demonstrates that the Mangyeong River is currently very wide and shallow. The planform geometry for the Mangyeong River is definitely straight with a sinuosity as low as 1.03. The thalweg and mean bed elevation profiles were analyzed using field measurements in 1976, 1993 and 2009. The measured profiles indicated that the channel has degraded about 2 m since 1976. The coarse gravel material and large width-depth ratio increase the stability of the bed material in this reach.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.7 no.4
• /
• pp.48-57
• /
• 1997

This paper presents the automatic construction and parameter optimization technique for fuzzy logic controllers using genetic algorithm. In general. the design of fuzzy logic controllers has difficulties in the acq~lisition of expert's knowledge and relies to a great extent on empirical and heuristic knowledge which, in many cases, cannot be objectively justified. So, the performance of the controllers c:an be degraded in the case of plant parameter variations or unpredictable incident which a designer may have ignored, and the parameters of fuzzy logic controllers obtained by expert's control action may not be optirnal. Some of these problems can be resolved by the use of genetic algorithm. The proposed method can tune the parameters of fuzzy logic controllers including scaling factors and determine: the appropriate number of fuzzy rulcs systematically. Finally, we provides the second order dead time plant to evaluate the feasibility and generality of the proposed method. Comparison shows that the proposed method can produce fuzzy logic controllers with higher accuracy and a smaller number of fuzzy rules than manually tuned fuzzy logic controllers.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.1
• /
• pp.5-15
• /
• 2017

Skin friction may be one of the most critical factors in designing the prebored and precast pile. Special attention was given to the interface behavior of cement milk-surrounding soil during the installation of prebored and precast pile. Small-scale field model pile test was conducted for the case of single pile. The size and geometry of the small-scale field model piles were designed with pile length 1.3m, boring diameter 0.067 m. Quick maintain-load test was conducted for the cases of boring diameter 150, 125, 90, 86, 74 mm and water-cement ratio 90, 70, 60%. It was shown that the bearing capacity of the pile increased as the cement-water ratio and cement milk thickness increased. Considering the scale effect between the small-scale model test and the actual construction site, it was found that cement milk thickness of 0.1~0.4D (50~200 mm) was reasonable for the stability of the structure. Also, the proper cement paste water / cement ratio was about 70% when considering the results of this study and quality control.

• KSBB Journal
• /
• v.19 no.4
• /
• pp.331-334
• /
• 2004

In vivo characterization of FadB homologous enzymes including PaaG, YdbU and YgfG for medium-chain-length (MCL) polyhydroxyalkanoate (PHA) biosynthesis was carried out in fadB mutant Escherichia coli. Previously, it was reported that amplification of FadB homologous enzymes such as PaaG and YdbU in fadB mutant E. coli resulted in enhanced biosynthesis of MCL-PHA by greater than two fold compared with control strain. In this study, we constructed paaG fadB double mutant E. coli WB114 and ydbU fadB double mutant E. coli WB115 to investigate the roles of PaaG and YdbU in biosynthesis of MCL-PHA. Inactivation of paaG and ydbU genes in fadB mutant E. coli harboring Pseudomonas sp. 61-3 phaC2 gene reduced the MCL-PHA production to 0.16 and 0.16 PHA g/L, respectively from 2 g/L of sodium decanoate, which are much lower than 0.43 PHA g/L obtained with fadB mutant E. coli WB101 harboring the phaC2 gene. Also, we identified new FadB homologous enzyme YgfG, and examined its roles by overexpression of ygfG and construction of ygfG fadB double mutant E. coli WB113.

• Proceedings of the Korean Society of Computational and Applied Mathematics Conference
• /
• 2003.09a
• /
• pp.1-1
• /
• 2003

In this talk, a reduced-order modeling methodology based on centroidal Voronoi tessellations (CVT's)is introduced. CVT's are special Voronoi tessellations for which the generators of the Voronoi diagram are also the centers of mass (means) of the corresponding Voronoi cells. The discrete data sets, CVT's are closely related to the h-means clustering techniques. Even with the use of good mesh generators, discretization schemes, and solution algorithms, the computational simulation of complex, turbulent, or chaotic systems still remains a formidable endeavor. For example, typical finite element codes may require many thousands of degrees of freedom for the accurate simulation of fluid flows. The situation is even worse for optimization problems for which multiple solutions of the complex state system are usually required or in feedback control problems for which real-time solutions of the complex state system are needed. There hava been many studies devoted to the development, testing, and use of reduced-order models for complex systems such as unsteady fluid flows. The types of reduced-ordered models that we study are those attempt to determine accurate approximate solutions of a complex system using very few degrees of freedom. To do so, such models have to use basis functions that are in some way intimately connected to the problem being approximated. Once a very low-dimensional reduced basis has been determined, one can employ it to solve the complex system by applying, e.g., a Galerkin method. In general, reduced bases are globally supported so that the discrete systems are dense; however, if the reduced basis is of very low dimension, one does not care about the lack of sparsity in the discrete system. A discussion of reduced-ordering modeling for complex systems such as fluid flows is given to provide a context for the application of reduced-order bases. Then, detailed descriptions of CVT-based reduced-order bases and how they can be constructed of complex systems are given. Subsequently, some concrete incompressible flow examples are used to illustrate the construction and use of CVT-based reduced-order bases. The CVT-based reduced-order modeling methodology is shown to be effective for these examples and is also shown to be inexpensive to apply compared to other reduced-order methods.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.1841-1850
• /
• 2013

The various types of fishways are installed at the multi-functional weirs in the four major rivers to minimize the negative effect due to the construction of the transverse structures. The movable weir was installed at the upstream of the ice-harbor type artificial fishway of the Dalseong weir in the Nakdong river, which can control the fishway flowrate regardless of the river flowrate. The incoming flowrate to the artificial fishway is closely related with the hydraulic characteristics that dominate the fish passage efficiency. Thus, it is crucial to find out the weir operation rule for properly sustaining efficient fish-passage, such as the optimized flowrate. In this study, the FLOW-3D was used to analyze and compare the various hydraulic characteristics associated with the passage efficiency, based upon the given different flowrate, and subsequently provide the optimized flowrate for the fishway movable weir to maintain the best efficient flow condition for the fish-passage.

• Archives of design research
• /
• v.11 no.2
• /
• pp.117-126
• /
• 1998

The underground space which has been highlighted anew in view of urban scenery and environmental conservation through the control of ground development and solution of urban problems through making the utility of urban space efficient can promote the urban service, amenity, stability and others by arranging the urban function of ground area to the underground which is anticipated to be demanding the more in the future an also can be effective measures of confrontation in the solution of traffic, the complex in the heart of the city and lack of land through effective construction of the structure of urban space. But it has been understood to be extremely negative space at this time as limited to negative and fragmentary development and it has faced the necessity of constructing pleasant environment by overcoming every problem. After all, through the general research of underground space, this dissertation is reconsidering the development value of environmental design on the basis of the case study in international city development of underground space, and trying to extract design factors which should be treated in developing the underground space by establishing the evaluation model on the functional, techinical and behavioral elements factors.