• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.579-585
• /
• 2017

Development of a facade system that can reduce load factor and costs in high-rise building construction is required. The proposed cable wall system is used as a structural support by the glass-cable and can increase openness on lower elevations and the lobby area. Its use in high-rise buildings can reduce construction costs. Without transferring directly a strong initial tension of the cable to the building frame is connected to the steel member and the reinforced concrete structures, by absorbing the initial tension of the cable, it is possible to control the occurrence of a strong concentrated loads to the structure. Comparison of load-displacement test results from the numerical analysis with the test results showed reasonable agreement, Therefore, the proposed numerical results confirm good prediction of cable behavior for the facade system.

• Tunnel and Underground Space
• /
• v.9 no.2
• /
• pp.131-140
• /
• 1999

Although there have been lots of geological or geotechnical surveys for construction sites, most of data obtained from these surveys have not been reused properly for the future construction work due to the absence of systematic management of data management system. This research, therefore, has focused on the development of DB system, Rockmass Information Management System(RIMS), to save, manage and reuse these abandoned data, specially test data of rock and rockmass with site conditions. RIMS has not only the basic functions of inputting, modifying, and dynamic searching of data but also several data control modules which can manage, input and correct, analyse and report data. Furthermore it saves data such as strata status, laboratory test results, in-site test results, and so on using 3-dimensional data stacking up structure. It is using x, y coordinates to represent horizontal positions and depth to represent vertical position of data. With the development of RIMS, this research has analyzed and classified present conditions of data in RIMS according to region, rock type, etc.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.22 no.4
• /
• pp.102-115
• /
• 2019

This study aims to establish and apply a drought vulnerability assessment plan including various factors related to drought. The evaluation technique consisted of three stages: evaluation factor and weight selection, evaluation data database construction, evaluation data and weight combination, and Delphi investigation method was applied to evaluation factor and weight selection. As the evaluation method, the TOPSIS method, which is a widely used MCDM method, was used. The results of the drought vulnerability assessment were applied to the administrative districts of Sigun-gu, Korea from March 2016 to September 2019. As a result of the evaluation, drought vulnerable areas were identified in Chungcheongbuk-do, Gyeongsangnam-do, and Jeollanam-do, and it was analyzed that it is necessary to establish drought response plans for these areas.

• Architectural research
• /
• v.22 no.2
• /
• pp.41-52
• /
• 2020

Laboratory buildings with specialized equipment and ventilation systems pose challenges in terms of efficient energy use and initial construction costs. Additionally, lab spaces should have flexible and efficient layouts and provide a comfortable indoor research environment. Therefore, this study aims to identify the correlation between the facade of a building and its interior layout from case studies of energy-efficient research labs and to propose passive energy design strategies for the establishment of an optimal research environment. The case studies in this paper were selected from the American Institute of Architects Committee on the Environment Top Ten Projects and Leadership in Energy and Environmental Design (LEED) certified research lab projects. In this paper, the passive design strategies of space zoning, façade design devices to control heating and cooling loads were analyzed. Additionally, the relationships between these strategies and the interior lab layouts, lab support spaces, offices, and circulation areas were examined. The following four conclusions were drawn from the analysis of various cases: 1) space zoning for grouping areas with similar energy requirements is performed to concentrate similar heating and cooling demands to simplify the HVAC loads. 2) Public areas such as corridor, atrium, or courtyard can serve as buffer zones that employ passive solar design to minimize the mechanical energy load. 3) A balanced window-to-wall ratio (WWR), exterior shading devices, and natural ventilation systems are applied according to the space programming energy requirements to minimize the dependence on mechanical service. 4) Lastly, typical laboratory space zoning categories can be revised, reversed, and even reconfigured to minimize the energy load and adjust to the site context. This study can provide deep insights into various design strategies employed for construction of green laboratories along with intuitive arrangement of various building components such as laboratory spaces, lab support spaces, office spaces, and common public areas. The key findings of this study can contribute towards creating improved designs of laboratory facilities with reduced carbon footprint and greenhouse emissions.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.2
• /
• pp.149-161
• /
• 2012

The use of seismic energy-dissipative devices for passive control is increasing exponentially in the recent years for both new and existing buildings. Use of these devices started in and has been somewhat limited to developed countries. One of the current challenges is to promote the use of seismic dampers in earthquake-prone developing countries by lowering the cost of the devices. This paper proposed a new type of seismic damper based on yielding of a cantilever type metallic element for seismic retrofit of existing and new building structures. The hysteretic behavior and energy dissipation capacity of the proposed damper was investigated using component tests under cyclic loads. The experimental results indicated that the damping device had stable restoring force characteristics and a high energy dissipation capacity. Based on these results, a simple hysteretic model for predicting the load-displacement curve of the seismic damper was proposed.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.6
• /
• pp.427-438
• /
• 2016

This study is experimental research for the effect of gap at the end plate on the performance of extended end-plate type splice. For this research, simple beam type specimens by using extended end-plate type splice are planned. Main variables are the initial gap between end-plates, the installation of finger shim plate before the installation of high tension bolts, the final gap between end-plates, and the installation of finger shim plate after the installation of high tension bolts. The static loading tests results show that the maximum bending strength of splice is not dependent on the gap, but the vertical displacement, initial stiffness and elastic stiffness are affected by the gap. In addition to that, the possibility of brittle fracture is increased when the torque of high tension bolt is used to control the gap. Thus, careful consideration is needed in this case.

• Geotechnical Engineering
• /
• v.3 no.1
• /
• pp.7-24
• /
• 1987

Preloading surcharge method along with vertical drains was adopted to improve the performance of a very soft marine clay deposit. The onshore deposit, located in the Ulsan Bay area, consists of a 2 to 10m thick, very soft, highly compressible marine clay layer developed just below. the sea water level. The initial undrained shear strength of the clay layer was about 0.6 ton/m2. But, the deposit was designed after treatment to support some auxiliary facilities for a new ilo refinery plant, requiring bearing capacities of 3.6 to 5.4 ton/m2 and maximum allowablee settlement of less than 7.5cm. A total of 35, 000 wick drains Ivas installed to expedite drainage during preloading, and surcharge loads of up to 5m above the original ground level were applied in a step-by-step loading sequence to prevent ground failure by excess surcharge loads. An extensive program of field instrumentation was implemented to monitor the behavior of the clay deposit. Measurers!ends included settlements, excess pore pressure and its dissipation, ground farmer level fluctuation, and lateral movement of the so(t clay layer under the preloads. This paper describes the design concepts, construction methods and control procedures used for improvement of the clay layer. It also presents the ground behavior measured during construction, rind comparisons with theoretical predictions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.766-777
• /
• 2008

Currently in increasing number of urban tunnels with small overburden are excavated according to the principle of the New Austrian Tunneling Method (NATM). Successful design, construction and maintenance of NATM tunnel demands prediction, control and monitoring of ground displacement and support stress high accuracy. A magnetic anisotropy sensor is used for nondestructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of a ferromagnetic material is measured in a nondestructive manner, which then can be translated into the absolute values of stresses existing on the surface of the material. This technique was applied to measure stresses of H-beams, used as tunnel support structures, to confirm expected measurement accuracy with reading error of about 10 to 20 MPa, which was confirmed by monitoring strains released during cutting tests The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction and maintenance of underground rock structures encountered in civil and mining engineering.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1452-1457
• /
• 2010

Recently, coal ash is used as resources to make controlled low-strength material (CLSM) which a self-compacted, cementitious material used primarily as a backfill in lieu of compacted fill. Pozzolanic reaction is strongly related with self-cementation of coal ashes. However, this reaction depends on pozzolanic content in fill materials and is disappeared in 2-3 days after placement of coal ash fill. Therefore, state of coal ash fill is commonly very loose and not appropriate for foundations of structures without special treatments. In this study, a coal ash placement device was developed to place coal ashes effectively to improve density of coal ash fills. The device consists of a ribbon type mixer to obtain homogeneous materials mixture and a piston type pump for density control of fill materials. Based on several laboratory test results, more stable coal ash fill state can be obtained with controlling placement pressure.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1392-1397
• /
• 2010

Currently in increasing number of urban tunnels with small overburden are excavated according to the principle of the New Austrian Tunneling Method(NATM). Successful design, construction and maintenance of NATM tunnel demands prediction, control and monitoring of ground displacement and support stress high accuracy. A magnetic anisotropy sensor is used for non-destructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of a ferromagnetic material is measured in a non-destructive manner, which then can be translated into the absolute values of stresses existing on the surface of the material. This technique was applied to measure stresses of H-beams, used as tunnel support structures, to confirm expected measurement accuracy with reading error of about 10 to 20MPa, which was confirmed by monitoring strains released during cutting tests The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction and maintenance of underground rock structures encountered in civil and mining engineering.