• 한국환경과학회지
• /
• 제30권3호
• /
• pp.245-255
• /
• 2021

In this study, we evaluated the effect of the type of sewage sludge (digested, non digested) on drying efficiency according to the polymer injection rate. The drying characteristics were shown using a near-infrared ray (NIR) and a microwave. As a result of the drying characteristics with NIR at a polymer dose ratio of 8%, the heating up period is up to 6 minutes after the start of the drying experiment. Afterwards, the constant rate drying period of the digested sludge (A, C and G sites) was 6 minute → 18 minute, showing a rapid decrease in moisture. On the other hand, non digested sludge (B, D, E, F, H, I, J and K sites) showed gradual drying characteristics compared to digested sludge until complete drying (10%). As the polymer dose ratio of 10% and 12%, the heating up period for digested sludge is up to 6 minute after the start of the experiment. Afterwards, the constant rate drying period of the digested sludge was 6 minute → 20 minute, showing a rapid decrease in moisture. On the other hand, the heating up period of non digested sludge was up to 10 minute after the start of the experiment, and the constant rate drying period was 10 minute → 22 minute, which was shorter than digested sludge. As a result of the drying characteristics with microwave at a polymer dose ratio of 8%, 10% and 12%, the constant rate drying period the digested sludge was 4 minute → 20~22 minute, showing a rapid decrease in moisture. On the other hand, non digested sludge of the constant rate drying period was 4 minute → 22~30 minute, which was longer than digested sludge.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.254-259
• /
• 2009

The mixed cooling dryer has been developed significantly by adopting both advantages of cooling dryers and desiccant dryers. In this study, it is introduced that the desired effect, such as drying rate period reduction and energy-saving, could be achieved only by adding the desiccant dryer if an existing cooling dryer is used. The experiment should be conducted for quite long time due to the material selection, so it is regrettable that there are not enough data.

• 한국식품과학회지
• /
• 제25권5호
• /
• pp.558-564
• /
• 1993

쌀보리를 시료로 하여 건조조건을 다르게 하여 유동층 건조특성에 영향을 미치는 외부요인에 대해서 조사한 결과를 요약하면 다음과 같다. 쌀보리의 유동층건조는 항률건조기가 없이 감률건조 1단계, 감률건조 2단계의 두 단계로 일어남을 알 수 있었다. 또한 건조속도상수는 충전량이 적을수록, 공기속도가 클수록, 공기온도가 높을수록, 상대습도가 낮을수록 켰으며, 감율건조단계에서의 건조속도상수는 Arrhenius형의 plot에서 좋은 직선관계를 나타내어 이 단계가 활성화 과정임을 알 수 있으며, 감률건조 제 1단계의 활성화 에너지는 1900ca1/gmol, 감률건조 제 2단계의 활성화 에너지는 2500ca1/gmol을 각각 나타내었다.

• 분석과학
• /
• 제10권6호
• /
• pp.418-426
• /
• 1997

고주파를 이용한 오니의 건조특성에 대하여 살펴보고 재래식 건조특성과 비교 분석하였다. 고주파 건조는 빠른 속도와 높은 효율을 보였다. 재래식 건조에서는 항율건조기간이 나타나지 않았고 수분은 모세관현상에 의하여 이동하였다. 오니의 수분 중 자유수와 결합수는 존재하지 않았다. 고주파 건조에서 감율건조기간이 두 부분으로 나타났으며, 수분의 이동은 확산에 의하여 일어났다. 증발 표면적이 커질수록 수분의 제거가 촉진되었고, 오니의 지름이 커질수록 넓은 범위의 항율건조 기간이 나타났으며, 모양에 따라서도 건조특성이 다르게 나타났다. 고주파 건조에서는 오니의 중심부에서 가장 먼저 온도가 상승하였으며, 항율건조기간에서 $80{\sim}100^{\circ}C$로 일정하게 유지되면서 가장 높았다.

• 한국식품과학회지
• /
• 제14권4호
• /
• pp.342-349
• /
• 1982

송풍식건조과정(送風式乾燥過程) 중의 말쥐치육의 건조기구(乾操機構)와 수분활성(水分活性)과의 관계를 검토하기 위하여 $47.5^{\circ}C$에서 풍속과 공기의 상대습도를 달리하여 실험한 결과를 요약하면 다음과 같다. 전체 건조과정은 정속건조기(定速乾燥期)와 감속건조기(減速乾燥期)로 구분되었다. 정속건조기(定速乾燥期)는 건조표면(乾燥表面)이 수분활성(水分活性) 1.0을 유지하는한 계속되었으며, 온도와 상대습도가 일정할 때 정속건조속도(定速乾燥速度)는 공기의 속도(速度)의 제곱근에 비례하였다. 감속건조기(減速乾燥期)는 건조기구(乾操機構)가 서로 다른 제(第)1 및 제(第)2감속건조기(減速乾燥期)로 구분되었다. 제(第)1감속건조기(減速乾燥期)는 모세관 응축수의 건조표면(乾燥表面)으로의 이동이 불충분한 불포화표면건조기(不飽和表面乾燥期)였으며, 이 때의 건조속도(乾燥速度)는 공기의 온도가 일정할 때 상대습도에 크게 좌우되었다. 제(第)1감속건조기(減速乾燥期)와 제(第)2감속건조기(減速乾燥期)의 변환점에서 표면경화현상(表面硬化現象)이 시작되었다. 상대습도의 변화에 따라 제(第)2감속건조기(減速乾燥期)가 시작될 때의 수분활성(水分活性)과 수분함량(水分含量)은 각각 다른 값을 나타내었다. 제(第)2감속건조기(減速乾燥期)는 다시 건조기구(乾操機構)를 달리하는 두 개의 건조기(乾燥期)로 구분되었다. 제(第)2감속건조기(減速乾燥期)의 1단계는 말쥐치육 내부의 모세관 응축수가 건조표면(乾燥表面)으로 확산, 증발하여 건조가 진행되었으며, 이때의 수분의 확산계수는 $47.5^{\circ}C$에서 $2.89{\cdot}10^{-10}m^2/sec$였다. 표면경화현상(表面硬化現象)은 말쥐치육의 수분활성(水分活性)이 0.7에 이를때까지 계속되었다. 제(第)2감속건조기(減速乾燥期)의 2단계는 수분활성(水分活性) 0.45에서 시작되었다. 이 때의 건조는 말쥐치육 내부에 다분자층(多分子層)으로 흡착(吸着)한 결합수의 건조표면(乾燥表面)으로의 확산, 증발에 의하여 진행되었다. 흡착수분(吸着水分)의 분자층(分子層)의 수는 4였으며, $47.5^{\circ}C$에서의 확산계수는 $4.38{\cdot}10^{-11}m^2/sec$였다.

• 환경위생공학
• /
• 제13권1호
• /
• pp.9-15
• /
• 1998

Microwave heating and drying processes have been well established in various industrial applications. Feasibilities of successful application of microwave drying to many material have been shown on the laboratory or pilot-plant scale. The microwave drying behavior of plating sludge are considered in this paper. The plating sludge containing 70%, 80% and 90% water exposed to microwave power at 2,450 MHz, 700W. An experimental microwave drying apparatus was designed and constructed to monitor weight loss during drying. By studying the drying characteristic curve, the moisture in sludge was almost classified into two categories : free moisture and intestinal moisture. And the critical moisture contents at which the drying rate ceases to be constant were from 10.1 to 10.5%. A simple drying model is proposed which may be used to describe drying behavior of plating sludge. The constant rate and the falling rate periods in microwave drying were addressed separately. From the eqation of constant rate period the drying rate constants decreased exponentially with increasing depth. Microwave heating compared with conventional heating offered higher heating rates from 9 to 16 times. Therefore, microwave drying process can be effective in removing moisture from plating sludge.

• Journal of Biosystems Engineering
• /
• 제19권2호
• /
• pp.112-123
• /
• 1994

At present, no appropriate drying conditions can be found for the heated-air drying of mushroom in Korea. Usually, mushroom is being dried at the temperature range of 40 to $50^{\circ}C$ until the moisture content reaches 10~13% (wb). However, drying characteristics of the mushroom should be investigated for quality improvement and efficient drying operation of the mushroom. The results of this study may be summarized as follows ; 1. The effect of air temperature on the rate of drying was greater than that of relative humidity for drying of mushroom, and the rate of drying was increased with increase in the air temperature. 2. Drying rate for Shiitake mushroom showed falling-rate period of drying without constant-rate period of drying. Drying rate for Oyster mushroom showed a short constant-rate period at the initial stage of drying process, and followed by falling-rate period of drying. 3. Exponential and App.-Diffusion models were found to describe well the drying process of Shiitake mushroom. Exponential and Thompson models for Oyster mushroom in which Thompson model was the most suitable for Oyster mushroom. 4. The equilibrium moisture content of the mushroom decreased with decrease in the air temperature and increase in the relative humidity. In room condition($20^{\circ}C$, 54% RH), the calculated values of the equilibrium moisture content showed 11.17% for Shiitake mushroom and 13.19% for Oyster mushroom, respectively.

• 한국식품과학회지
• /
• 제21권2호
• /
• pp.203-211
• /
• 1989

근채류를 열풍건조할 경우 수축변형 및 표면 경화현상을 일으켜 품질변화를 수반하게 되므로 본 연구에서는 온도, 상대습도 및 풍속을 조절할 수 있고 건조중의 시료크기 변화를 측정할 수 있는 실험실 규모의 건조장치를 제작하여 무우 및 고구마의 건조특성과 수축특성에 영향을 미치는 외부 요인들에 대해 조사하였다. 건조속도는 무우 및 고구마 모두 항률건조기, 감률건조기, 감률건조 2단계 a 및 b의 4단계로 구분되어 나타났다. 수축속도 곡선은 각각 건조속도에 대응하여 기울기가 다른 4단계로 나타났으며 항률건조 기간에서는 수축속도가 서서히 증가하다가 감률건조 1단계에서 급격히 증가하였고 감률건조 2단계의 초기에 상당하는 점에서 최대에 달하였다. 또한 시료의 두께. 상대습도 및 초기 함수율 등은 표면적 수축에 큰 영향을 미쳤고 시료의 두께가 얇을수록, 그리고 상대습도 및 초기 함수율이 높을수록 평형 상태에서의 수축율은 증가하였다.

• 한국동물학회지
• /
• 제3권1호
• /
• pp.19-23
• /
• 1960

A method for determination of thyroid secretion rate in rabbit by means of radioactive iodine presented. After injection of radioactive iodine, in vivo determination so f radioactivity in thyroid gland were made during a 19 day-experimental period. In the same period blood samples were drawn and analyzed for protein-bound iodine (PBI) and for protein-bound radioactive iodine(PBI181). A rate constant for secretion of thyroid hormone was calculated from the disappearance rate of radioactive iodine in thyroid gland. The secretion rate of radioactive hormone iodine was calculated by multiplying this rate constant by the amount of radioactive iodine present in thyroid gland. Assuming that the specific radioactiveness of the circulating thyroid hormone and of the hormone just secreted were identical , thyroid secretion rate was calculated by the equation. {{{{ { Secreted hormone-iodine , gamma /hr} over { Secreted hormone-I^131, % dose/hr }= { PBI, ${\gamma}$/ml.Serum} over { PBI^131 , % dose/ml . Serum } }} The method presented consisted of measurements for series of independent criteria on thyroid function, and the resulting thyroid secretion rate was calculated by combination of those.

• 한국환경보건학회지
• /
• 제24권1호
• /
• pp.24-31
• /
• 1998

This study was performed to investigate the difference in species of test fish on the determination of short-term bioconcentration factor in zebrafish(Brachydanio rerio), red sword tail(Xiphophorus hellieri) and goldfish(Carassius auratus). Experimental concentrations of carbamates were 0.05 and 0.10 ppm and chlorothalonil were 0.005 and 0.01 ppm for 3 and 5 days, respectively. This paper reports the measured BCF value on pesticides in various species of test fish, under steady state, and examined correlation between the BCF value and depuration rate constant or LC$_{50}$ or lipid content. Carbamates and chlorothalonil concentration in fish extract and BCF of carbamate and chlorothalonil were increased as incresing test concentration. Carbamates concentration in fish extract and BCF of carbamate were decreased as incresing test period, but chlorothalonil concentration in fish extract and BCF of chlorothalonil were increased as prolonging test period. Determined pesticide concentration in fish extract and BCF were highest in red sword tail, and followed by goldfish, and zebrafish. Determined depuration rate constant were highest in zebrafish, and followed by goldfish, and red sword tail. 96hr-LC$_{50}$ were highest in red sword tail, and followed by zebrafish, and goldfish. Lipid compositions were highest in red sword tail, and followed by goldfish, and zebrafish. Therefore, it is suggested that the difference of BCF between each pesticide due to those of lipid composition of fish and deputation rate constant, while LC$_{50}$ have no effect on BCF.