• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.564-568
• /
• 2006

Smooth picture module is operated by vibration to tilt the light from the DMD (digital micro mirror device) of DLP projection TV, which makes the screen of the TV smoother and DMD chip cost lower. To satisfy the vibration characteristics of smooth picture module, it is designed by optimizing moment of inertia, spring constant and damping coefficient, using structural and fluid dynamic simulation that showed a good agreement with experimental data. To reduce the material cost and moment of inertia, engineering plastic is used and the reliability is estimated. A VCM (voice coil motor) type actuator for smooth picture has to satisfy performance requirements such as higher driving force, lower power consumption, and lower cost. The initial design and optimization for VCM was performed using FE analysis. It allowed us to optimize the design of magnetic circuit of the proposed actuator to obtain higher force while maintaining a lower cost.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12A
• /
• pp.2050-2058
• /
• 2001

In this paper, we propose the filtered-x least mean fourth (LMF) algorithm where the error raised to the power of four is minimized and analyze its convergence behavior for a multiple sinusoidal acoustic noise and Gaussian measurement noise. Application of the filtered-x LMF adaptive filter to active noise cancellation (ANC) requires estimating of the transfer characteristic of the acoustic path between the output and error signal of the adaptive controller. The results of 7he convergence analysis of the filtered-x LMF algorithm indicates that the effects of the parameter estimation inaccuracy on the convergence behavior of the algorithm are characterized by two distinct components : Phase estimation error and estimated gain. In particular, the convergence is shown to be strongly affected by the accuracy of the phase response estimate. Also, we newly show that convergence behavior can differ depending on the relative sizes of the Gaussian measurement noise and convergence constant.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.397-400
• /
• 1989

The interrupting capability of circuit breaker to have an effect on stability and reliability of the power system is largely determined by the fault current and prospective TRV (prospective transient recovery voltage). The prospective TRV, which is essentially a system function determined by the elements of the connected circuit, is not constant for a given system location but is affected by a number of variables. Therefore, the purpose of this study is to analyze the prospective TRV of KEPCO's 345KV transmission system by using EMTP (Electro-Magnetic Transients Program) and to compare the calculated values with the standard values in KSB 150 (1976)

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.258-263
• /
• 1989

The configuration of Brushless DC moter is similar to the permanent magnet Synchronous moter. Power transistors are oftenly used to supply the switching by feedback signals of rotor positioning sensors. Brushless DC moter have been used in Aerospace and Robotics where the electromagnetic noise or the sparking of the commutator contact can not be tolerated and long - lived maintenance - free operation is required. This paper describes the design of the microprocessor - based controller for the Brushless DC moter. The controller is designed to operate for the constant torque generation and variable speed control using sinusoidal PWM inverters and resolvers as rotor positioning sensors.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.3
• /
• pp.188-196
• /
• 1987

This paper describes a design method for the buck type switching regulator to improve transient and steady state performances. Necessary design considerations on the power stage are given before designing the controller to obtain better trandient responses with less control effort and a feedforward compensation is also given to effectively improve the steady state performance. In the design of the controller, a PIM (proportional-integral-measurable) control method with optimized constant feedback gains is presented to get better tansient and steady state performances without complicating the implementation of controller. Computer simulations and experimental results are given to show the usefulness of the presented technique.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.6
• /
• pp.545-556
• /
• 1990

A design method of a current source using 12-pulse phase-controlled rectifier (PCR) is presented. The critical inductance of the 12-pulse PCR is derived and it is shown that the critical inductance can be reduced using a current source. The control circuit of the 12-pulse PCR with an inner fast dynamic loop is proposed to give the frequency synchronism and to reduce the subharmonics due to the unbalance of the transformer of the power line. This circuit is analyzed and its dynamic loop is optimized. The optimal constant PIMF (proportional, integral and measurable variable feedback, and feedforware) controller is also designed using the time-weighted quadratic performance index. It is shown via experimental results that the proposed design method gives high dynamic and static performance of the current source using the 12-pulse PCR.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.64-70
• /
• 1995

We discussed the thermal analysis for a recording media with the variation of the laser pulse duration, the laser power and the temperature distribution in order to optimize the Te-based antireflection structure from the computer calculations. In the case that the radial heat diffusion is negligible, we can calculate the maximum temperature of the recording layer at the center of the spot by the Simple Model. The temperature profile of the recording layer is obtained from the Numerical Model by considering the total specific heat and the latent heat. As a result, the effect of the heat sinking acting as a thermal loss for the hole formation could be minimized by introducing the pulse with the hole formation duration(.tau.) below the thermal time constant(.tau.$_{D}$) of a dielectric layer. These requirments can be satisfied by using the dielectric thickness of the 2nd ART(Anti-Reflection Trilayer) condition or the dielectric materials with a low thermal diffusivity.y.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.7
• /
• pp.597-601
• /
• 2002

In this study, the structural, dielectric and piezoelectric properties of $Pb[(Ni_{1/3}Nb_{2/3})_x-(Mn_{1/3}Nb_{2/3})_{0.09-x}-(Zn_{0.505}Ti_{0.495)_0.91]O_3$ (x=0, 0.01, 0.02, 0.03, 0.04, 0.05) system ceramics were investigated to develop the composition ceramics for piezoelectric transformer. All the specimens were sintered at $1250^{\circ}C$ and its physical properties were measured, and the results are as follows : With increasing PNN substitution for PMN-PZT system, dielectric constant was increased and electro-mechanical coupling factor($k_p$) was increased to 0.62 at 5 mol% while mechanical quality factor(Qm) was decreased.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2685-2687
• /
• 1999

This paper is concerned on developing DC-DC converter. In contrast to resonant converter, this converter requires no external resonant elements and operates with constant switching frequency. In conventional PWM converter, two MOSFET switches of the converter are simultaneously turned on and turned off. In presented converter, to achieve Zero Voltage Switching, the two legs of the bridge are operated DC-DC converter is phase shifted. Phase shifted Full Bridge ZVS PWM Converter have an effect on the power system. Operation principle and features are illustrated by the experiment results from 50W, 250kHz with MOSFET switch.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2556-2558
• /
• 1999

We present voltage-source inverter for variable speed of washing machine. In the case of previous washing machines only on/off contol of motor was satisfied but these days the desire of customers moves to more silent and energy saving machine. Therefore many white goods manufacturers consider variable driving methods of motor. Nowadays variable speed Induction motors powered by inverters are becoming more and more popular. In this paper the principles of constant V/F control of Induction motor used in washing machine and space vector PWM technique are reviewd. Implementation issues such as command voltage generation, switching pattern determination, speed and power measurement are also presented. Experimental results are included in the end of the paper.