• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1540-1542
• /
• 1997

Plasma polymerized thin films were fabricated by interelectrode capacitively coupled type apparatus. FT-IR analyses indicated that the thin film spectra are composed not only of the corresponding monomer bands but also of several new bands. Relative dielectric constant and dielectric loss tangent of thin films fabricated in the discharge power of 90[W] showed $3.212{\sim}3.805$ and $0.0026{\sim}0.0451$ in alternating frequency of $10^3{\sim}10^6$[Hz]. Contact angle measurement indicated that cross-link of the films is increased with the discharge power.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.61-69
• /
• 2016

This study is the results related to the combustion instability phenomenon with respect to combustor length and thermal power as variables in dual swirling combustor configuration. Especially, the beating phenomena having the insensitive resonance frequency of relatively constant peaks are observed when the combustor lengths increase in a lower power regime. This beating phenomenon might be occurred due to the interacting behaviors of pilot and main burners with different periods. Therefore, such insensitive response seems to be a result of the beating phenomenon with interaction between the pilot and main flames even though the combustor lengths are increased.

• Journal of Power System Engineering
• /
• v.1 no.1
• /
• pp.51-60
• /
• 1997

In this paper, we investigated the heating performance and the basic characteristics required for normal combustion of kerosene fan heater. And also the iso-velocity contours and the iso-temperature contours of hot gas discharged from the exit of kerosene fan heater were analyzed. The experiment was carried out with kerosene fan heater attached to the blow-down-type subsonic wind tunnel with a test section of $240mm{\times}240mm{\times}1200mm$. The purpose of this paper was to obtain the basic data for new design from conventional kerosene fan heater. Consequently it was found that (i) the pressure ratio $P_2/P_1$ had a comparatively constant value of 0.844 according to the increase of the revolution of turbo fan, (ii) the primary excess air ratio had a range of $0.84{\sim}1.11$ during normal combustion, and (iii) the heating performance of kerosene fan heater had a range of $1,494{\sim}3,852kcal/hr$.

• Journal of Power System Engineering
• /
• v.18 no.2
• /
• pp.62-69
• /
• 2014

In this paper, in order to investigate the effects of marco and microscopic observations of fatigue crack growth in friction stir welded (FSWed) 7075-T651 aluminum alloy plates, fatigue crack growth tests were performed under constant amplitude loading condition at room temperature with three different pre-cack locations, namely base metal (BM-CL) and two kinds of pre-crack locations in welded joints, weld metal (WM-CL) and heat affected zone (HAZ-CL) specimens. The fatigue crack growth behavior of FSWed 7075-T651 aluminum alloy plates were discussed based on the marco and microscopic fractographic observations. The marcoscopic aspects of surface crack growth path for BM-CL and HAZ-CL specimens indicate relatively straight lines, however, the crack growth paths of WM-CL specimens grow first straight and by followed toward the TMAZ and HAZ. The microscopic aspects of fatigue fracture for BM-CL and HAZ-CL specimens indicate typical fatigue striation, but WM-CL showed intergranular fracture pattern by micro structural changes of FSW process.

• Journal of Power System Engineering
• /
• v.22 no.1
• /
• pp.56-63
• /
• 2018

After the recent fabrication of diesel vehicle exhaust gas by Volkswagen, nitrogen oxides ($NO_x$) and particulate matter (PM) are drawing attention as representative pollutants included in exhaust gas. When gasoline and diesel fuels are combusted through direct injection into a combustion chamber at high pressure, PM emission is actually increased. To find a solution to this problem, a basic study was conducted to derive an optimized variable for combustion of compressed natural gas (CNG) by applying CNG, acknowledged as a clean fuel, to direct injection system. The essence of this study is in the introduction of a radical ignition technology for compressed natural gas (RI-CNG) in a sub-chamber type engine. The direct injection system was applied to a sub-chamber to remove residual gas from previous combustion cycle. In addition, optimal mixer distribution was achieved by precisely setting ignition timing based on fuel injection timing and excess air ratio.

• Nuclear Engineering and Technology
• /
• v.17 no.2
• /
• pp.98-104
• /
• 1985

A number of reactivity devices are distributed in a CANDU-PHWR core to control the power distribution and excess reactivity. The effects of these devices are represented by incremental cross sections in core analysis. The incremental cross sections are generated by the SUPERCELL code using the two-group constant set calculated by the lattice code, WIMS. The incremental cross sections are then assessed for adjusters and zone controller by core simulation. Reactivity worth and channel powers are compared to the reference values. The deviation of reactivity worth and the maximum channel power are less than 0.97% and 0.6%, respectively, for the initial and equilibrium core.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.182-187
• /
• 1996

Deformation characteristics of miniature plate tensile specimens have been studied to develop the thickness requirement and a correlation to estimate the mechanical properties of bulk material from miniature specimen data. The material used was a SA 508 C1.3 reactor pressure vessel steel and the thicknesses of miniature tensile specimens varied from ().12 m to 2 mm. The effects of thickness on the tensile deformation properties such as strength, ductility, and necking characteristics were analyzed. The yield and ultimate tensile strengths were independent of specimen thickness when the thickness was larger than about 0.2 mm. The uniform and total elongations decreased as the specimen thickness decreased. It was also observed that the uniform strain component in the width direction decreased with decrease in the specimen thickness, however, that in the thickness direction was rather constant in total thickness range studied. Based on this observation and a relationship between the necking angle and the ratio between strain components, a correlation between the uniform elongations of miniature specimen and standard specimen was derived. The uniform elongations calculated by this new correlation agreed well with the measured values.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2045-2056
• /
• 2016

The input impedances of pulse width modulated (PWM) dc-to-dc converters, which dictate the outcomes of the dynamic interaction between dc-to-dc converters and their source subsystem, are analyzed in a general and unified manner. The input impedances of three basic PWM dc-to-dc converters are derived with both voltage mode control and current mode control. This paper presents the analytical expressions of the 24 input impedances of three basic PWM dc-to-dc converters with the two different control schemes in a factorized time-constant form. It also provides a comprehensive reference for future dynamic interaction analyses requiring knowledge of the converters' input impedances. The theoretical predictions of the paper are all supported by measurements on prototype dc-to-dc converters. The use of the presented results is demonstrated via a practical application example, which analyzes the small-signal dynamics of an input-filter coupled current-mode controlled buck converter. This elucidates the theoretical background for the previously-reported eccentric behavior of the converter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.368-377
• /
• 1999

In this paper, the wide-band CDMA transmitter for 2 GHz band is designed and implemented. The CC-OQPSK implemented as ASIC has better spectral and power efficiency than the conventional QPSK system because it has constant envelope characteristics. Good harmonics rejection characteristics and gain of 20 dB are shown on the intermediate frequency stage using double-conversion scheme. The output power of two-stage RF amplifier is +2l.14 dBm in 1.9 GHz band. It is confirmed that the electrical characteristics of the transmitter satisfy with required the specification of the wide-band CDMA transmitter for 2 GHz band.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.515-520
• /
• 2018

A large number of lithium-ion batteries are arranged in series and parallel in battery packs, such as those in electric vehicles or energy storage systems. As battery packs age, their output power and energy density drop because of voltage deviation, constant and non-uniform exposure to abnormal environments, and increased contact resistance between batteries; this reduces application system efficiency. Despite the balancing circuit and logic of the battery management system, the output of the battery pack is concentrated in the most severely aged unit cell and the output is frequently limited by power derating. In this study, we implemented a cell imbalance detection algorithm and selected parameters to detect a sudden decrease in battery pack output. In addition, we propose a method to increase efficiency by applying the measured testing values considering the operating conditions and abnormal conditions of the battery pack.