• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.640-650
• /
• 2018

A TRIAC dimmable LED driver with a wide tuning range and a two-stage uniform dimming scheme is proposed in this paper. To solve the restricted dimming range problem caused by the limited conduction ratio of TRIAC dimmers, a conduction ratio compensation technique is introduced, which can increase the output current up to the rated output current when the TRIAC dimmer turns to the maximum conduction ratio. For further optimization, a two-stage uniform dimming diagram with a rapid dimming curve and a slow dimming curve is designed to make the LED driver regulated visually uniform in the whole adjustable range of the TRIAC dimmer. The proposed control chip is fabricated in a TSMC $0.35{\mu}m$ 5V/650V CMOS/LDMOS process, and verified on a 21V/500mA circuit prototype. The test results show that, in the 90V/60Hz~132V/60Hz ac input range, the voltage linear regulation is 2.6%, the power factor is 99.5% and the efficiency is 83%. Moreover, in the dimming mode, the dimming rate is less than 1% when the maximum dimming current is 516mA and the minimum dimming current is only about 5mA.

• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.96-105
• /
• 2017

In this paper, a hybrid modular multilevel converter (MMC) topology with an improved nearest level modulation method is proposed for medium-voltage high-power applications. The arm of the proposed topology contains N series connected half-bridge submodules (HBSMs), one full-bridge submodule (FBSM) and an inductor. By exploiting the FBSM, half-level voltages are obtained in the arm voltages. Therefore, an output voltage with a 2N+1 level number can be generated. Moreover, the total level number of the inserted submodules (SMs) is a constant. Thus, there is no pulse voltage across the arm inductors, and the SM capacitor voltage is rated. With the proposed voltage balancing method, the capacitor voltage of the HBSM is twice the voltage of the FBSM, and each IGBT of the FBSM has a relatively low switching frequency and an equalized conduction loss. The capacitor voltage balancing methods of the two kinds of SMs are implemented independently. As a result, the switching frequency of the HBSM is not increased compared to the conventional MMC. In addition, according to a theoretical calculation of the total harmonic distortion of the electromotive force (EMF), the voltage quality with the presented method can be significantly enhanced when the SM number is relatively small. Simulation and experimental results obtained with a MMC-based inverter verify the validity of the developed method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.11
• /
• pp.1003-1008
• /
• 2002

In this paper, the estimation of lifetime with the various conditions of the interface between toughened epoxy and rubber which are consisting materials of underground power delivery system has been studied. After the measurement of the short time AC interfacial breakdown strength on macro interfaces at room temperature, the breakdown time at several voltages were measured under the constant voltages lower than the short time breakdown voltage. The long time breakdown voltage was calculated by using Inverse Power Law. Two types of interfaces was studied. One was the interface between toughened epoxy and EPDM(Ethylene Prorylene Diene Terpolymer). The other was the interface between toughened epoxy and silicon rubber. Interfacial pressure and roughness of interfaces was determined through the characteristic of short time AC interfacial breakdown strength. Oil condition was no oiled, low viscosity oiled and high viscosity oiled. High viscosity oiled interface between Toughened epoxy and silicon rubber had the best lifetime exponent, 20.69. and the breakdown voltage of this interface after 30 years was evaluated 19.27㎸.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.116-119
• /
• 2005

In this paper, we propose the PLL system of the local oscillator system for the millimeter wave band's radio astronomy receiving system. The development of the proposed local oscillator system based on the YIG oscillator VCO with 26.5 ${\sim}$ 40GHz specification. This system consists of the oscillator part including the YIG VCO, the harmonic mixer, and the isolator, the RF processing part including the triplexer, limiter, and RF discrimination processor. and the PLL system including YIG modulator and controller. Based on this configuration. we verify the frequency and power stability of the developed local oscillator system according to some temperature variation. From this test results we confirm the stable output frequency and power characteristic performance of the developed La system at constant temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.193-193
• /
• 2008

Wearable and ubiquitous micro systems will be greatly growing and their related devices should be self-powered in order to avoid the replacement of finite power sources, for example, by scavenging energy from the environment. With ever reducing power requirements of both analog and digital circuits, power scavenging approaches are becoming increasingly realistic. One approach is to drive an electromechanical converter from ambient motion or vibration. Vibration-driven generators based on electromagnetic, electrostatic and piezoelectric technologies have been demonstrated. Among various generator types proposed so far, piezoelectric generator possesses considerable potential in micro system. To overcome low mechanical-to-electric energy conversion, the piezoelectric device should activate in resonance mode in response to external vibration. Normally, the external vibration excretes at low frequency ranging 0.1 to 200 Hz, whereas the resonant frequencies of the devices are fixed as constant. Therefore, keeping their resonant mode in varying external vibration can be one of important points in enhancing the conversion efficiency. We investigated the possibility of use of multi-bender type piezoelectric devices. To match the external vibration frequency with the device resonant frequency, the various devices with different resonant frequency were chosen.

• Journal of IKEEE
• /
• v.1 no.1 s.1
• /
• pp.164-175
• /
• 1997

In this paper, the CE-OQPSK that has constant envelope was designed for applying PSK to the nonlinear amplifier so as to improve power efficiency. For this realization. ROM and D/A converter that have relative low power consumption were used. As a result of comparing the PSD (Power spectrum density) of CE-OQPSK with that of conventional OQPSK through simulation for estimating the performance. In case of correlation factor ${\alpha}$ = 0.707. the improvement of bandwidth efficiency of 5% and 20% is achieved in the main lobe and the sidelobe, respectively. And, in case additional bandwidth-limiting-filter is added, it can be shown that the PSD of CE-OQPSK meet the FCC wireless LAN spectrum specification.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.5
• /
• pp.33-41
• /
• 2015

Organic Rankine cycle (ORC) has been used to generate electrical or mechanical power from low-grade thermal energy. Usually, this thermal energy is not supplied continuously at the constant thermal energy level. In order to optimally utilize fluctuating thermal energy, an axial-type turbine was applied to the expander of ORC and two supersonic nozzle were used to control the mass flow rate. Experiment was conducted with various turbine inlet temperatures (TIT) with the partial admission rate of 16.7 %. The tip diameter of rotor was to be 80 mm. In the cycle analysis, the output power of ORC was predicted with considering the load dissipating the output power produced from the ORC as well as the turbine efficiency. The predicted results showed the same trend as the experimental results, and the experimental results showed that the system efficiency of 2 % was obtained at the TIT of $100^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.71-79
• /
• 2004

Packet-type data transmission is characterized by the continuous transmission of massive data with relatively constant rate. In such transmission, the dynamic power consumed on buses is influenced by the sequence of transmitted data. A new coding scheme called Sequence-Switch Coding (SSC) is proposed in this paper. SSC reduces the number of bus transitions in the transmission of packet-type data by changing the sending order of the data. Some simple algorithms are presented, In. The simulation results show that SSC outperforms the well-known Bus-Invert Coding with these algorithms. SSC is not a specific algerian but a method to reduce the number of bus-transitions. There could be lots of algorithms for realizing SSC. The variety of SSC algorithms provides circuit designers a wide range of trade-off between performance and circuit complexity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.6
• /
• pp.844-849
• /
• 2012

In this paper, a bidirectional Zeta-Flyback converter is proposed. The topology of the proposed converter is analyzed, which is superposition of bidirectional Flyback converter mode and bidirectional Zeta converter mode in a cycle. The proposed converter allows power flow in either a forward direction or a backward direction. Bidirectional power flow is obtained by a transformer and components. The proposed converter's output is controlled by duty of constant frequency PWM of switch. Compared to conventional bidirectional isolated DC-DC converters, the proposed isolated bidirectional DC-DC converter has high power density and high transformer utilization. To confirm the proposed converter, the simulation and experimental results are presented.

• Journal of Advanced Marine Engineering and Technology
• /
• v.11 no.4
• /
• pp.59-74
• /
• 1987

In this dissertation, a complete model of commutatorless static Kramer type slip power recovery system of 3.phi. induction motor has been designed and tested in the laboratory, and the experimental results are compared with the numerical values. The main results of this study are summerized as follows. (1) Maintenance and repair of the mechanical commutator is obviated by adopting a thyristor commutator in place of the mechanical commutator in the conventional Kramer system. (2) The experimental results of developed torque, and stator current are generally coincided with the numerical values obtained by the derived equation, proving their validity. (3) This system is simulated and the following operational characteristics are obtained with suitable design values : (a) The speed control range of 7:1 is obtained when the turn ratio of induction motor is lowered to about 3:1 to 4:1 and the generating constant of auxiliary synchronous motor is increased to 120-175 range. (b) Its efficiency can be increased to 75-85%, the range for static Scherbius system and its power factor takes values in the range of 65-85%, which is twice of the range for static Scherbius system.