• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.9
• /
• pp.1325-1333
• /
• 2017

The sensorless control of blushless DC motor(BLDCM) is based on the $120^{\circ}$ control in which the back electromotive force(Back EMF) for estimating the position of the rotor can be detected. However, the $120^{\circ}$ control has a disadvantage that the torque constant is small as compared with $180^{\circ}$ control which can not detect the back EMF. The $150^{\circ}$ control which complements these problems makes it possible to detect the back EMF and improve the torque constant by 12.5% compared to the $120^{\circ}$ control. Therefore, this paper compares the output characteristics of BLDCM through finite element method analysis (FEA) by the conventional and proposed control methods of BLDCM for water circulation system and proposes design for downsizing and weight reduction of BLDCM according to secured torque constant. The validity of the proposed control and design proposal is proved through simulation and experimental results by comparing the output characteristics of $120^{\circ}$ control and $150^{\circ}$ control.

• Composites Research
• /
• v.31 no.6
• /
• pp.365-370
• /
• 2018

One of the critical parameters to improve the output power for triboelectric nanogenerators (TENGs) is the surface charge density. In this work, we modify the tribo-material of TENG by introducing the $TiO_x$ embedded Polydimethylsiloxane (PDMS) in anatase and rutile phase. The effect of dielectric constant and electronic structure of the $TiO_x$ on the capacitance of TENG and the output power as well are discussed. The surface charge density is increased as the control of the dielectric constant in difference weight percent of $TiO_x$ and PDMS. As the results of that, the 5% $TiO_x$ rutile phase and 7% $TiO_x$ anatase phase embedded PDMS exhibit the highest TENG output. The peak value of voltage/current obtained from $TiO_x$ rutile and anatase phase are ${\sim}180V/8.2{\mu}A$ and $211.6V/8.7{\mu}A$, respectively, at the external force of 5 N and working frequency of 5 Hz, which gives over 12-fold and 15-fold power enhancement compared with the TENG based on the pristine PDMS film. This study provides a better understanding for TENG performance enhancement from the materials view.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2407-2414
• /
• 1992

Constant temperature hot wire air flow meter for automobiles requires temperature compensation system because hot wire output signal is sensitive to ambient temperature variations as well as fluid velocity. The objectives of the present study are to design an air flow meter circuit which is capable of compensating the hot wire output signal for ambient temperature variations and to investigate the mechanism of such temperature compensation. This circuit is composed of platinum hot wire, platinum resistor, two variable resistors, a constant resistor and a DC-amplifier. In particular, by simply replacing a constant resistor in one of the bridge arms of the conventional circuit with platinum resistor and a variable resistor for the purpose of temperature compensation, the deviation of output signal with respect to ambient temperature variations between 27deg. C 70deg. C could be reduced to less than 2.5% for mass flow rate and to less than 5% for velocity respectively. The mechanism of temperature compensation against ambient temperature variations was explained by means of measuring the heat transfer coefficient with hot wire temperature variations and analyzing and analyzing conventional empirical equations qualitatively.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.333-336
• /
• 2002

An alternative CMOS implementation of a multi-output four-terminal floating nullor (FTFN) with constant-g$_{m}$ rall-to-rail input stage is proposed. This presented circuit is based on the advantages of a complementary transconductance amplifier and class AB dual translinear cell circuit that comes up with wide bandwidth. The constant-g$_{m}$ characteristic is controlled by the maximum-current selection circuits, maintaining the smooth response over the change of input common mode voltage. The circuit performances are confirmed through HSPICE simulations. A current-mode multifunction filter is used to exhibit the potentiality of this proposed scheme.eme.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.111-116
• /
• 2015

In this study, the constant current converter for LED lighting was designed and the electrical characteristics of the fabricated SMPS was measured. When the output current is 300mA the maximum efficiency of 85% was shown and the output current is in the range of 100~400mA efficiency over 70% were exhibited. Also the dimming levels control over the range of 0 to 100% was possible by using a control signal of 0~250mV.

• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.1190-1200
• /
• 2018

A current sourced bi-directional wireless power transfer (WPT) system is proposed to solve the problems that exist in the bi-directional WPT for vehicle-to-grid (V2G) systems. These problems include the fact that these systems are not safe enough, the output power is limited and the control methods are complicated. Firstly, the proposed system adopts two different compensation and control methods on both the primary and secondary sides. Secondly, based on an AC impedance analysis, the working principle is analyzed and the parameter configuration method with frequency stability is given. In order to output a constant voltage, a bi-directional DC/DC circuit and a controllable rectifier bridge are adopted, which are based on the "constant primary current, constant secondary voltage" control strategy. Finally, the effectiveness and feasibility of the proposed methods are verified by experimental results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.2
• /
• pp.260-267
• /
• 2015

An LCL-type isolated dc-dc converter is analyzed, using ac approximation. Analyses to express characteristics on the proposed converter are derived under steady and ideal elements conditions in this paper. The two operating modes can be identified from the analysis results representing different device conduction sequences. This converter is capable of achieving required output voltage(step up or down) operations with inductance ratio while operated at fixed frequency with constant duty ratio-50%. Experimental results show that the designed converter based on Q has zero voltage switching and constant output voltage at different load variations to verify the analysis.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.10
• /
• pp.1845-1849
• /
• 2010

We have proposed and fabricated a Buck-Boost DC to DC Converter for Thermoelectric generator (TEG) with constant output voltage suitable for battery chargers or constant voltage supplies in the range of several watt. The experimental and simulation results have shown that the proposed method allows stable operation with maximum 86% power transfer efficiency. The proposed circuit has a merit in cost and miniaturization of a system compared to conventional MPPT algorithms, because the proposed method adopts only analog circuit without DSP or micro controller unit for calculating peak power point by iterative methods.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.85-90
• /
• 1998

A parallel-resonant converter with zero-voltage-switching, pulse-width-modulation(ZVS-PWM) control is proposed. Similar to the previously proposed series-resonant counterpart, it has a simple structure and can be controlled at a constant switching frequency using an active-clamp technique. The nearly constant current output characteristic of the parallel-resonant converter lends itself beneficially to precisely controlled constant current power supply applications. An experimental breadboard featured an accuracy of $\pm$1% for an output current of 2A, with an efficiency of 75%.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.609-618
• /
• 2013

This paper proposes a primary side constant power control scheme for TRIAC dimmer compatible LED drivers. The LED driver is a Flyback converter operated in boundary conduction mode (BCM) to minimize the switching loss. With the proposed control scheme, the input power of the Flyback converter can be controlled by the TRIAC dimming angle, which is not affected by AC input voltage variations. Since the output voltage is almost constant for LED loads, the output current can be changed by controlling the input power with a given conversion efficiency. The isolated feedback circuit is eliminated with the proposed primary side control scheme, which dramatically simplifies the whole circuit. In addition, the input current automatically follows the input voltage due to the BCM operation, and the resistive input characteristic can be achieved which is attractive for TRIAC dimming applications. Experimental results from a 15W prototype verify the theoretical analysis.