• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.7
• /
• pp.12-22
• /
• 2012

The main drawback of the multi-code spread spectrum communication system, which spreads data bits stream by the multiplexed orthogonal codes, is the need for the highly linear amplifier. Several constant amplitude precoding schemes have been proposed for the Walsh code or the extended $m$-sequence based multi-code spread spectrum systems. In the constant amplitude spread spectrum systems the accompany code is transmitted together with orthogonal codes to maintain the transmitter output in a constant level. In this paper we propose the use of the accompany in the receiver to improve the BER performance. The proposed receiver has the capability to correct the code detection error(up to one code error). We carried out simulations to verify the validity of the proposed algorithm. BER performance improvement was noticed compared with the conventional receiver.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.397-397
• /
• 2016

Triboelectric nanogenerators (TENG) can produce power from ambient mechanical sources and have strong points of high output performance, light weight, low cost, and easy manufacturing process. It is expected that TENG can be utilized in the fields of wireless electronics and self-powered devices in the world which pays attention to healthcare and the IoT. In this work, we focus on scavenging ambient rotational energy by using a durably designed TENG. In previous studies regarding harvesting rotation mode energy, the devices were based on sliding mechanism and durability was not considered as a major issue. However friction by rotation causes reliability problems due to wear and tear. Therefore, in this study, we convert rotary motion to linear motion utilizing a cam by which we can then utilize contact-mode TENG and improve device reliability. In order to increase output performance, bumper springs were used below the TENG and the optimum value for the bumper spring constant was analyzed theoretically. Furthermore, the inserting a soft substrate was proposed and its effect on high output was determined to be due to an increase in the contact area. By increasing the number of cam noses, the output frequency was shown to increase linearly. For the purpose of maximum power transfer, the input impedance of the device was determined. Finally, to demonstrate the use of the C-TENG as a direct power source, it was installed on a commercial bicycle wheel and connected to 180 LEDs. In conclusion we present a rotational motion TENG energy scavenger system designed for enhanced durability and optimized output by appropriate choice of spring constants and substrate.

• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.270-273
• /
• 2007

We have investigated the output characteristics of the 946 nm Nd:YAG laser which is longitudinally pumped by a fiber coupled laser diode. The temperature of a Nd:YAG crystal mount was kept constant by a controller with thermoelectric cooler. As a result, we measured more intense output at a low temperature, and then the maximum output power was measured to be 870 mW when the pumping power and the temperature were 9.95 W and $5^{\circ}C$, respectively. It appeared that output was decreased above 10 W pump power because of the thermal effects in gain medium.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.5
• /
• pp.415-429
• /
• 2011

In this study, a single-phase quasi Z-source AC-AC converters with a series connection of the output terminals is proposed. The proposed system has configuration that the input terminals of two quasi Z-source AC-AC converters are connected in parallel and its output terminals are connected in series. The out of phase mode and in phase mode of the proposed system are presented. To verify the validity of the proposed converter, a DSP controlled hardware was made and PSIM simulation was executed. As a result, controlling the duty ratio of the converter, the desired buck-boost output voltages could be generated. For each modes, as compared with the single converter operation, the proposed converter could enhance the efficiency and input power factor according to different loads. Also, in case of the out of phase mode under the constant load, the efficiency and input power factor of the proposed system are increased 10[%], 35[%] respectively in compared with the single converter. And, the output voltage is constantly controlled in dynamic state in case while the load is suddenly changed.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.2
• /
• pp.121-125
• /
• 2014

This paper presents a successful stand-alone pico-hydro generation system using a high-efficiency interior permanent-magnet (IPM) synchronous generator. A 1-kW 4-pole V-type IPM generator with low voltage regulation is used for laboratory test in stand-alone hydro energy conversion system. It has been found from experimental results that the constant output voltage is supplied stably by the proposed system under wide speed range.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.5
• /
• pp.411-414
• /
• 2004

In this paper, a power controller and 3 phase voltage source inverter are proposed for the improvement of weldability of large scaler Mash seam welder. The welder system is designed for the low cost and the improvement of weldability. For this system, the thyristor convertor has performed constant current controlling in the output terminal by using PAM type inverter. We have simulated our algorithm and made a prototype welder for experiment. Through the experiment, we have confirmed the improvement of weldability of our system.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.400-402
• /
• 1996

The paper describes the control strategy and hardware design for forced commutation cycloconverter which was developed for ac servo motor drive application of vector control. 12-pulse cycloconverter is used to investigate experimentally the performance of an induction motor drive system. The cycloconverter has the facility for continuous control of both the frequency and magnitude of the output voltage to keep a constant flux in the induction motors.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.190-193
• /
• 2003

This paper Proposes 40 [KVA] rated SIV(Static Inverter) system for Light Rail Transit. The SIV Provide power of a fluorescent light in the car, Air-conditioner. and other equipments. To control output voltage it is used voltage control loop for constant voltage control and simultaneously used current control loop for instantaneous control at load changing. The Performance of SIV system will be verified by experimental results.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.68-69
• /
• 2011

Realistic amounts of time delay are found to have significant effects on the average output LED current and on the critical inductor value at the boundary between the two conduction modes. Especially, the time delay can provide an accurate LED current for the peak current controlled (PCC) buck converter with a wide input voltage. Experimental results are presented for the PCC buck LED driver with constant-frequency controller.

• 전기의세계
• /
• v.17 no.3
• /
• pp.39-42
• /
• 1968

We have been studying on the discharged phenomena if compound dielectrics for insulator which is very important in electric machinery and et al. In this paper we come to the couclusion that as a result of studying on the electric design of Ozonizer, the higher frequency becomes the better output could be got, and then discharge power could be the greatest by selecting the distance of the discharge gap and atomospheric pressure properly under the same applied voltage, and that power factor of the Ozonizer reached the maximum power at a particular frequency when the discharge power is maintained at constant.