• Resources Recycling
• /
• v.15 no.4 s.72
• /
• pp.36-43
• /
• 2006

There was some difficulty dewatering properties due to small porosity diameter of cake, when pigment sludge contained fine particle was formed by cake under the dewatering. It was difficult to dewater the sludge with fine particles with the conventional mechanical dewatering method. This study was to improve the dewatering rate as discharging the water from porosity of cake easily, supplying the low heat to the cake layer. Thermal dewatering equipment of piston type to keep up constant temperature on the cake was set up and relative experiment was conducted for sludge of 200 g with fine pigment particle. As test results. filtration of 176.8 g, cake weight of 19.4 g, cake thickness of 4.2 mm was measured, and it was analyzed that the water content of cake was 47 wt% and dewatering velocity, which moaned the residual d교 sloid amount per dewatering area, was $2.1DS\;m^{2}{\cdot}cycle$. This results showed that filtration increased, cake weight and thickness decreased and dewatering velocity increased against mechanical dewatering method. And water content of cake decreased about 30%, so the result which dewatering rate improved was drew generally. The reason is that the inner vapor pressure working at the cake porosity increased as applying the low heat to the cake layer, which lead to discharge the water from porosity easily. Therefore, this study was estimated by the useful technology for sludge reduction.

• Bulletin of the Korean Chemical Society
• /
• v.2 no.3
• /
• pp.96-104
• /
• 1981

(1) The flow data of f (stress) and ${\dot{s}$ (strain rate) for Fe and Ti alloys were plotted in the form of f vs. -ln ${\dot{s}$ by using the literature values. (2) The plot showed two distinct patterns A and B; Pattern A is a straight line with a negative slope, and Pattern B is a curve of concave upward. (3) According to Kim and Ree's generalized theory of plastic deformation, pattern A & B belong to Case 1 and 2, respectively; in Case 1, only one kind of flow units acts in the deformation, and in Case 2, two kinds flow units act, and stress is expressed by $f={X_1f_1}+{X_2f_2}$where $f_1\;and\;f_2$ are the stresses acting on the flow units of kind 1 and 2, respectively, and $X_1,\;X_2$ are the fractions of the surface area occupied by the two kinds of flow units; $f_j=(1/{\alpha}_j) sinh^{-1}\;{\beta}_j{{\dot{s}}\;(j=1\;or\;2)$, where $1/{\alpha}_j\;and\;{\beta}_j$ are proportional to the shear modulus and relaxation time, respectively. (4) We found that grain-boundary flow units only act in the deformation of Fe and Ti alloys whereas dislocation flow units do not show any appreciable contribution. (5) The deformations of Fe and Ti alloys belong generally to pattern A (Case 1) and B (Case 2), respectively. (6) By applying the equations, f=$(1/{\alpha}_{g1}) sinh^-1({\beta}_{g1}{\dot{s}}$) and $f=(X_{g1}/{\alpha}_{g1})sinh^{-1}({\beta}_{g1}{\dot{s}})+ (X_{g2}/{\alpha}_{g2})\;shih^{-1}({\beta}_{g2}{\dot{s}})$ to the flow data of Fe and Ti alloys, the parametric values of $x_{gj}/{\alpha}_{gj}\;and\;{\beta}_{gs}(j=1\;or\;2)$ were determined, here the subscript g signifies a grain-boundary flow unit. (7) From the values of ($({\beta}_gj)^{-1}$) at different temperatures, the activation enthalpy ${\Delta}H_{gj}^{\neq}$ of deformation due to flow unit gj was determined, ($({\beta}_gj)^{-1}$) being proportional to , the jumping frequency (the rate constant) of flow unit gj. The ${\Delta}H_{gj}\;^{\neq}$ agreed very well with ${\Delta}H_{gj}\;^{\neq}$ (self-diff) of the element j whose diffusion in the sample is a critical step for the deformation as proposed by Kim-Ree's theory (Refer to Tables 3 and 4). (8) The fact, ${\Delta}H_{gj}\;^{\neq}={\Delta}H_{j}\;^{\neq}$ (self-diff), justifies the Kim-Ree theory and their method for determining activation enthalpies for deformation. (9) A linear relation between ${\beta}^{-1}$ and carbon content [C] in hot-rolled steel was observed, i.e., In ${\beta}^{-1}$ = -50.2 [C] - 40.3. This equation explains very well the experimental facts observed with regard to the deformation of hot-rolled steel..

• Geophysics and Geophysical Exploration
• /
• v.8 no.1
• /
• pp.78-85
• /
• 2005

This study, combining geophysical and environmental approaches, was undertaken to investigate the causes of secondary salinity in the Goondoola basin, in southwestern Queensland. Airborne radiometric, electromagnetic and ground electromagnetic datasets were acquired, along with data on soils and subsurface materials and groundwater. Relationships established between radiometric, elevation data, and measured material properties allowed us to generate predictive maps of surface materials and recharge potential. Greatest recharge to the groundwater is predicted to occur on the weathered bedrock rises surrounding the basin. Electromagnetic data (airborne, ground, and downhote), used in conjunction with soil and drillhole measurements, were used to quantify regolith salt store and to define the subsurface architecture. Conductivity measurements reflect soil salt distribution. However, deeper in the regolith, where the salt content is relatively constant, the AEM signal is influenced by changes in porosity or material type. This allowed the lateral distribution of bedrock weathering zones to be mapped. Salinisation in this area occurs because of local-andintermediate-scale processes, controlled strongly by regolith architecture. The present surface outbreak is the result of evaporative concentration above shallow saline groundwater, discharging at break of slope. The integration of surficial and subsurface datasets allowed the identification of similar landscape settings that are most at risk of developing salinity with groundwater rise. This information is now being used by local land managers to refine management choices that prevent excess recharge and further salt mobilisation.

• International Area Studies Review
• /
• v.15 no.3
• /
• pp.239-261
• /
• 2011

The cyclicality of productivity has been one of the essential issues in macroeconomics. Since Solow(1957) developed the dominant approach to the measurement of productivity growth, Solow's approach, which assumes the perfect competition, the constant returns to scale, and the full use of input factor has been modified particularly in Hall's(1990) and Basu's(1996) works. Their researches take account of market power, returns to scale, and variable factor utilization. This paper establishes the empirical model based on Hall's(1990) and Basu's(1996) models, estimates 4 types of Solow's reidual in manufacturing and 2 service industries over the period 1975:1-2010:4, and analyzes the cyclicality of measured productivity. The result proved the measured productivity to be procyclical in manufacturing industries and electricity and water industry, and in contrast to the Basu's, the variable factor utilization transformed the countercyclicality of measured productivity into its procyclicality in the Korean economy.

• International Area Studies Review
• /
• v.15 no.2
• /
• pp.77-100
• /
• 2011

The Korean economy have experienced the remarkable decreases in factor prices such as bond yields, real wage since the IMF foreign exchange crisis. This paper investigates the effects of the price changes in the factor markets on determining the level and cyclicality of industrial markups in the manufacturing industry. For this purpose, we construct a markup equation in the small open economy based on the production function including foreign intermediate goods and assuming constant returns to scale technology and AR(1) process of technological coefficient. Empirical results are summarized as the followings. The empirical results shows that the increased markups after the IMF crisis can be explained by the price decreases in the factor markets which result in lowering marginal costs. And we also observed counter cyclicality of markup, labor share and interest rates while real wages, technical coefficients, and production price index proved to be pro-cyclical. In conclusion, the price changes in factor market have contributed to the stickiness in markup fluctuation in the manufacturing industry.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.695-700
• /
• 2018

This paper presents the development of compact and lightweight broadband power amplifier module using HMIC (Hybrid Microwave Integrated Circuit) technology that could be high-density integration for many non-packaged microwave components into the small area of a high dielectric constant printed circuit board, such as a ceramic substrate, also using the special design and fabrication schemes for the structure of minimized electromagnetic interference to obtain the homogeneous electrical performance at the wideband frequency. The results confirmed that the small signal gain has a gain flatness of ${\pm}1.5dB$ within the range of 32 to 36 dB. In addition, the output power satisfied more than 30 dBm. The noise figure was measured within 7 dB, and OIP3 (Output Third Order Intercept Point) was more than 39 dBm. The fabricated broadband power amplifier satisfied the target specification required to electrically drive the high power amplifiers of jamming generators for electronic warfare, so the actual applicability to the system was verified. Future studies will be aimed at designing other similar microwave power amplifiers in the future.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.12
• /
• pp.1881-1889
• /
• 2018

Objective: In dryland areas of China, alfalfa hay (AH) is a possible substitute for concentrate feed for beef cattle. To evaluate the potential benefits of this substitution, we studied the effect of the ratio of AH intake to total dry matter (DM) intake on average daily body-weight gain (ADG), dietary energy utilization status, and economic benefit in Gansu province. Methods: In each of two feeding trials in 2016 (trial 1 [T1], July 3 to 17; trial 2 [T2], August 15 to September 23), crossbred male Simmental calves were allocated to low AH (LA), medium AH (MA), and high AH (HA) feeding groups (n = 4 per group). The target ADG was set as 1 kg for both trials. In a one-way-layout design based on conventional feeding practices in the province, calves received diets containing the different AH amounts, with a constant ratio of corn stover:total DM and decreasing rations of concentrate feed proportional to the increase in AH. Calves in T1 received AH at 15% (T1-LA), 23% (T1-MA), or 31% (T1-HA) of their dietary DM allowances; those in T2 received 9% (T2-LA), 24% (T2-MA), or 34% (T2-HA) AH. Results: Among the T1 groups, both ADG and economic benefit were highest in T1-LA; whereas in T2, they were higher in the T2-LA and T2-MA groups than in T2-HA. Energy digestibility did not significantly differ among the groups in either trial. The dietary AH inclusion ratios of 14% in the warm season and 8% to 21% in the cool season appeared to yield optimal ADG, metabolizable energy intake, and economic benefit. Conclusion: Low-level inclusion of AH, ranging from 8% to 21%, is a practical approach for beef cattle feeding. This modified feeding regimen likely will promote increased growth performance during the fattening stage of beef steers in dryland areas of Gansu province, China.

• Journal of the Korean Society of Radiology
• /
• v.12 no.7
• /
• pp.845-852
• /
• 2018

This study aimed to investigate the difference of X-ray exposure by comparing and analyzing absorbed dose according to changes in the number of frames in coronary angiography, also depending whether the zoom mode is FOV enlargement or Zoom Live. Moreover, for appropriate frame selection measures for examination, including the effect of frame change on the image quality, were sought by measuring the noise strength expressed by the standard deviation (SD), the signal to noise ratio (SNR) and contrast to noise ratio (CNR). The study was conducted with an anthropomorphic phantom on an angio-system. The linear relationship between the frame rate and the radiation dose was evident. On the contrary, the indices of image quality (SD, SNR, and CNR) were almost constant irrespective of the number of frames. The difference depending on the zoom mode was not statistically significant for DAP, air kerma, and SD (p > 0.05). However, SNR and CNR were statistically different between FOV enlargement and Zoom Live. In conclusion, since the image quality was not degraded significantly with the decreasing frame rate from 30, 15, to 7.5 f/s and the radiation dose evidently decreases in almost exactly linear proportion to the decreasing frame rate, the number of frames per second needs to be maintained as low as reasonably achievable. As for the dependence on the zooming mode, the Live Zoom mode showed statistically significant improvement in the image quality indices of SNR and CNR and it justifies active use of the Live Zoom mode which enables real-time image enlargment without additional radiation dose.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.105-113
• /
• 2018

In this study, the engineering properties including bearing capacity of subgrades stabilized with a binder are analyzed by laboratory and field experiments. The main components of the binder are CaO and $SO_3$. After the binder was mixed with a low plasticity clay, the passing rates were relatively decreased as the sieve mesh size increased. Not only did the soil type change to silty sand, but engineering properties, such as the plasticity index and modified California bearing ratio (CBR), were improved for the subgrade. A comparison of the compaction curves of the stabilized subgrade and field soil compacted with the same energy demonstrated an increase of approximately 6% in the maximum dry unit weight, slight decrease in optimum moisture content, and considerable increase improvement in grain size. In the modified CBR test, the effect of unit weight and strength increase of the modified soil (with a specific amount of binder) was remarkably improved. As the proportion of granulated material increased after the addition of binder, the swelling was reduced by 3.3 times or more during initial compaction and 6.5 times by final compaction. The unconfined compressive strength of the specimens was maintained at the homogeneous value with a constant design strength. The stabilized subgrade was validated by applying it in the field under the same conditions; this test demonstrated that the bearing capacity coefficients at all six sites after one day of compaction exceeded the target value and exhibited good variability.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.3
• /
• pp.17-24
• /
• 2019

Carbon Fiber Reinforced Polymers(CFRP) has widely utilized as a material for rehabilitation because of its light-weight, deformability and workability. Because CFRP is brittle material whereas steel is ductile, it is inappropriate to apply conventional design approach for steel reinforcement. For ductile material, the behavior of combined elements is on average of that of unit element due to the stress redistribution between elements after yielding. Therefore, the mean value of the stress of combined elements is equal to that of unit element and the standard variation is smaller. Therefore, although the design value can increase, it is used as constant value because it is conservative and practical approach. However, for brittle material, the behavior of combined elements is governed by the weaker element because no stress redistribution is expected. Therefore, both the mean value and standard variation of the stress of combined elements decreases. For this reason, the design value would decrease as the number of element increases although it is eventually converged. In this paper, in brittle material, it is verified that the combination of unit element with normal distribution results in combined element with weibull distribution, so the modifying equation of mechanical properties is proposed with respect to the area load applied.