• 산업경영시스템학회지
• /
• 제14권24호
• /
• pp.163-168
• /
• 1991

In the FMS design, the important points are the selection of parts and the determination of configuration. The common approach method which solve the selection of parts are the determination of configuration has improved that the two points are simultaneously. This study finds the best method which parts combination and configuration are satisfied at the same time. And the optimal replace time of equipment under limited budget on the view Point of engineering. economy.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1763-1772
• /
• 2016

To reduce system complexity and implementation costs, fully-controlled H-bridge (FHB) modules and diode H-bridge PFC (DHB) modules are cascaded to form a hybrid cascaded H-bridge rectifier (HCHR). In this paper, the advantages of such a HCHR over other cascaded rectifiers are analyzed depending on the numbers of FHB modules and DHB modules. Therefore, to assign proper numbers to these two kinds of modules for the HCHR, a configuration determination method is investigated under balanced and imbalanced loads. Three principles are also presented to guide the configuration determination for the HCHR. In addition, the constraints for selecting the step-up ratio and filter inductance are derived based on a phasor diagram analysis. The proposed configuration determination method is validated by simulations under three different conditions in the PSIM environment. Finally, experiments are carried out on a scaled-down prototype where the configuration can be easily adjusted. The feasibility of the proposed theory is then verified by experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1998년도 제13차 학술회의논문집
• /
• pp.53-57
• /
• 1998

Star tracker placement configuration is proposed and the properness of the placement configuration is verified for star tracker's sun avoidance angle requirement. Precision attitude determination system is successfully designed using a gyro-star tracker inertial reference system for a candidate LEO spacecraft. Elaborate kalman filter formulation for a spacecraft is proposed for covariance analysis. The covariance analysis is performed to verify the capability of the proposed attitude determination system. The analysis results show that the attitude determination error and drift rate error are good enough to satisfy the mission of a candidate spacecraft.

• Applied Biological Chemistry
• /
• 제41권6호
• /
• pp.483-485
• /
• 1998

• Applied Biological Chemistry
• /
• 제41권4호
• /
• pp.261-264
• /
• 1998

Differently substituted styrylquinoline derivatives (6-9) were synthesized by condensation of quinaldine (1) and corresponding substituted benzaldehydes (2-5). Their relative configuration at C11-C12 and coupling patterns were determined by NMR techniques.

• 산업경영시스템학회지
• /
• 제24권67호
• /
• pp.19-26
• /
• 2001

A design issue for a flexible manufacturing system is to find the number of each resource type which assures a given production ratio with a minimal cost. The FMS is modeled as a closed queueing network with a local buffer of limited capacity. An efficient method to determine this optical configuration is presented. The proposed method consists of three steps : 1) determine a lower configuration, 2) derive a heuristic solution, 3) find the optimal solution. The derived heuristic solutions are close to the optical solution.

• Bulletin of the Korean Chemical Society
• /
• 제7권2호
• /
• pp.106-108
• /
• 1986

Exciton chirality method was applied for the determination of absolute configuration of panaxynol, a poly-yne compound from Panax ginseng roots for the first time. The circular dichroic spectra of panaxynol benzoates show the negative chirality at ${\lambda}_{ext}$, indicating the S configuration of C-3 chiral center.

• 제어로봇시스템학회논문지
• /
• 제12권3호
• /
• pp.300-306
• /
• 2006

In this paper an error analysis of 3-dimensional GNSS attitude determination system is given. The attitude error covariance matrix is derived and analyzed. It implies that attitude errors are affected by the baseline length and configuration, the satellites numbers and geometry, receiver measurement noises and the nominal attitude of the vehicle. By defining Euler Angle Dilution Of Precision (EADOP) which is analogous to GDOP, roll, pitch and yaw errors can be efficiently analyzed. However the expression of the attitude error is too complex to get some intuitions. Therefore with a commonly adopted assumption, new expressions for attitude error are derived. The formulas are easy to compute and represent the attitude error as a function of the nominal attitude of a vehicle, the baseline configuration and the receiver noise. Using the formula, the accuracy of the attitude can be analytically predicted without the computer simulations. Applications to some widely used configurations reveal the effectiveness of the proposed method.

• 한국전자현미경학회:학술대회논문집
• /
• 한국현미경학회 2000년도 제31차 추계학술대회
• /
• pp.59-60
• /
• 2000

• Journal of Welding and Joining
• /
• 제14권2호
• /
• pp.71-78
• /
• 1996

In order to rpovide proper SMT design criteria in a systematic way, a mathematical formulation has been developed to predict the configuration of the solder fillet formed between the gullwing type lead and rectangular pad. Effects of SMT design parameters such as the solder volume and pad dimension on the solder profile are investigated using the FEM that calculates the 3D configuration by minimizing the energy due to surface tension and gravity in the equilibrium state. Design criteria of QFP and SOP are illustrated by plotting the acceptable range of the solder volume with respect to the length and width ratios of the pad and lead. The results show that the acceptable design range increases with increase in the pad length and width. The pad length has more significant effects on design criteria compared with the pad width, and Bond number can be utilized to predict the joint quality.