• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.29 no.1
• /
• pp.59-70
• /
• 2011

The purpose of this study is to present raw data to systematically and rationally manage the protected trees located in Changwon-si, Korea. This study investigated about the present condition and the information of location, individual, management, health and soil. The results are as follows. The protected trees were located in 26 spots, and species of trees were 9 taxa; Zelkova serrata, Celtis sinensis, Aphananthe aspera, Ginkgo biloba, Carpinus tschonoskii, Pinus densiflora for. multicaulis, Quercus variabilis, Pinus densiflora and Salix glandulosa. In protected tree types, shade trees were the most, and the majority of theirs were 200 years or more in age. The range of altitude was 14~173m, and the number of trees located in flat fields was the most. For location types, village and field and mountain were presented in the order and, in land use, land for building was the most. The range of height was 8.0~30.0m, 0.6~5.1m in crown height, 240~700cm in diameter of breast and 210~800cm in diameter of root. In case of crown area, Zelkova serrata of No.5 was most large. The status boards were mostly installed except No.23 and No.26. The sites with fence were 9 spots, and the site with stonework were 14 spots. The sites with the support beam were 5 spots, and most sites were not covered up with soil. The materials of bottom were soil, gravel and vegetation in the order. The range of withering branch rate was 0~40%, and peeled bark rate was 0~60%. The sites made holes were 23 spots, and the hole size of Aphananthe aspera of No.12 was the largest. The sites disturbed by human trampling were 7 spots, the sites by disease and insects of 2 spots, the sites by injury of 23 spots and the sites by exposed roots of 13 spots. In the results of soil analysis, there showed that acidity was pH 4.5~8.0, organic matter content of 3.5~69.8g/kg, electrical conductivity(EC) of 0.11~2.87dS/m, available $P_2O_5$ of 3.0~490.6mg/kg, exchangeable K of 0.10~1.05cmol+/kg, exchangeable Ca of 1.41~16.45cmol+/kg, exchangeable Mg of 0.37~1.96cmol+/kg, exchangeable Na of 0.25~2.41cmol+/kg and cation exchange capacity(C.E.C) of 8.35~26.55cmol+/kg.

• Journal of agriculture & life science
• /
• v.53 no.1
• /
• pp.13-21
• /
• 2019

This study was carried out to acquire basic data for a long-term hydroponic culture through investigating water and inorganic ion uptake characteristics at different EC level of nutrient solution of three tomato varieties. Three different tomato varieties, the European type(cv. Daphnis), the Asian type(cv. Super Doterang) and cherry type(cv. Minichal), were used for the investigation. Also, the deep flow technique(DFT) was applied. The three different electrical conductivity(EC) level(1.0, 2.0, 3.0, and 4.0 dS·m-1) of hydroponic nutrient solution were used as variable. At a high EC level of nutrient solution, the leaf area and fresh weight decreased in the early stage, and its growth(plant height, leaf number, leaf area, fresh-weight) was poor with salt stress. Result showed that the higher the EC level of the nutrient solution, the lesser was water uptake. The water uptake was not significantly different from varieties in the first survey, but In the second survey, the 'Daphnis' did not show a significant decrease in water uptake in the EC level higher than 2.0 dS·m-1., on the other hand, 'Super Doterang' presented very low water uptake. At a low EC level, N, P, and K, were absorbed more than the concentration of the irrigation water, while Ca, Mg, S uptake were low. At a high EC level, almost ions absorbed less than 50% of the initial concentration of irrigation water. Thus, imbalance among ions was severe at low EC level compared to high EC level. 'Daphnis' was a variety that effectively utilize nutrients under nutrient stress, showing high absorption at low concentration condition and low absorption at high concentration condition. However, 'Daphnis' suffered most seriously by absorbing nutrients excessively.

• Journal of Bio-Environment Control
• /
• v.30 no.1
• /
• pp.1-9
• /
• 2021

This study was conducted to examine the changes of photosynthesis, growth, chlorophyll contents and functional material contents in light intensity and EC concentration of wild baby leaf vegetable, Indian lettuce (Lactuca indica L. cv. 'Sunhyang') in DFT hydroponics. The cultivation environment was 25±1℃ of temperature and 60±5% of relative humidity in growth system. At 14 days after sowing, combination effect of light intensity (Photosynthetic Photon Flux Density (PPFD 100, 250, 500 µmol·m-2·s-1) and EC level (EC 0.8, 1.4, 2.0 dS·m-1) of nutrient solution was determined at the baby leaf stage. The photosynthesis rate, stomatal conductance, transpiration rate and water use efficiency of Indian lettuce increased as the light intensity increased. The photosynthesis rate and water use efficiency were highest in PPFD 500-EC 1.4 and PPFD 500-EC 2.0 treatment. The chlorophyll content decreased as the light intensity increased, but chlorophyll a/b ratio increased. Leaf water content and specific leaf area decreased as light intensity increased and a negative correlation (p < 0.001) was recognized. Plant height was the longest in PPFD 100-EC 0.8 and leaf number, fresh weight and dry weight were the highest in PPFD 500-EC 2.0. Anthocyanin and total phenolic compounds were the highest in PPFD 500-EC 1.4 and 2.0 treatment, and antioxidant scavenging ability (DPPH) was high in PPFD 250 and 500 treatments. Considering the growth and functional material contents, the proper light intensity and EC level for hydroponic cultivation of Indian lettuce is PPFD 500-EC 2.0, and PPFD 100 and 250, which are low light conditions, EC 0.8 is suitable for growth.

• Journal of the Korean earth science society
• /
• v.41 no.6
• /
• pp.630-646
• /
• 2020

In rural areas, nitrate-nitrogen (NO3-N) pollution caused by agricultural activities is a major obstacle to the use of shallow groundwater as domestic water or drinking water. In this study, the water quality characteristics of shallow groundwater in Hyogyo-ri agricultural area of Yesan-gun, Chungcheongnam-do province was studied in connection with land use and chemical composition of soil layer. The average NO3-N concentration in groundwater exceeds the domestic and agricultural standard water qualities of Korea and is caused by anthropogenic sources such as fertilizer, livestock wastewater, and domestic sewage. The groundwater type mainly belongs to Ca(Na)-Cl type, unlike Ca-HCO3 type, a general type of shallow groundwater. The average NO3-N concentration (7.7 mg L-1) in groundwater in rice paddy/other (upstream, ranch, and residential) area is lower than the average concentration (22.8 mg L-1) in farm field area, due to a lower permeability in paddy area than that in farm field area. According to the trend analysis by the Mann-Kendall and Sen tests, the NO3-N concentration in the shallow groundwater shows a very weak decreasing trend with ~0.011 mg L-1yr-1 with indicating almost equilibrium state. Meanwhile, SO42- and HCO3- concentrations display annual decreasing trend by 15.48 and 13.15%, respectively. At a zone of 0 to 5 m below the surface, the average hydraulic conductivity is 1.86×10-5 cm s-1, with a greater value (1.03×10-4cm s-1) in sand layer and a smaller value (2.50×10-8 cm s-1) in silt layer.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.66 no.2
• /
• pp.171-181
• /
• 2021

The purposes of this study were to determine how changes in temperature affect germination rates and growth of hulled and dehulled barley, malting barley, and naked oat plants, and to measure chlorophyll content, photosynthetic efficiency, and secondary compounds (total phenol, total flavonoid, and 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activity) in plants grown at 13℃ or 25℃). Various types of barley seeds were collected from areas with ideal conditions for barley cultivation, hereinafter referred to as IA, and also from areas where barley cultivation is more difficult due to lower temperatures, hereinafter referred to as LTA. Seeds were tested for seed vigor. While there were significant differences in the electrical conductivity values between seeds collected from certain specific areas, no significant differences were evident between IA and LTA seeds, regardless of the type of barley seed. When plants were grown at 25℃, there were no significant differences in germination rates, plant height, root length and shoot fresh weight between plants originating from IA and LTA. However, there were differences in the measured parameters of some specific seeds. Similarly, under the low temperature condition of 13℃, no differences in the emergence rate, plant height, and shoot fresh weight were evident between plants originating from IA or LTA, regardless of the type of barley. However, there were differences between some specific seeds. One parameter that did vary significantly was the emergence date. Hulled barley and malting barley emerged 5 days after sowing, whereas naked oats emerged 7 days after sowing. There were no differences in the chlorophyll content and photosynthetic efficacy, regardless of the type of barley. There were no significant differences in total phenol, total flavonoid content, and DPPH radical scavenging activity between plants originating from IA and LTA, regardless of the type of barley. However, there were differences between some specific seeds. In particular, for malting barley the total flavonoid content differed in the order of Gangjin > Changwon > Haenam = Jeonju > Naju. The results indicate that crop growth, yield and content of secondary compounds in various types of barley may be affected by climate change.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.56-65
• /
• 2022

Copper is one of the non-ferrous metals used in the electrical/electronic manufacturing industries due to its superior properties particularly the high conductivity and less resistivity. The effluent generated from the surface finishing process of these industries contains higher copper content which gets discharged in to water bodies directly or indirectly. This causes severe environmental pollution and also results in loss of an important valuable metal. To overcome this issue, continuous R & D activities are going on across the globe in adsorption area with the purpose of finding an efficient, low cost and ecofriendly adsorbent. In view of the above, present investigation was made to compare the performance of a plant root (Datura root powder) as a bio-adsorbent to that of the synthetic one (Tulsion T-42) for copper adsorption from such effluent. Experiments were carried out in batch studies to optimize parameters such as adsorbent dose, contact time, pH, feed concentration, etc. Results of the batch experiments indicate that 0.2 g of Datura root powder and 0.1 g of Tulsion T-42 showed 95% copper adsorption from an initial feed/solution of 100 ppm Cu at pH 4 in contact time of 15 and 30 min, respectively. Adsorption data for both the adsorbents were fitted well to the Freundlich isotherm. Experimental results were also validated with the kinetic model, which showed that the adsorption of copper followed pseudo-second order rate expression for the both adsorbents. Overall result demonstrates that the bio-adsorbent tested has a potential applicability for metal recovery from the waste solutions/effluents of metal finishing units. In view of the requirements of commercial viability and minimal environmental damage there from, Datura root powder being an effective material for metal uptake, may prove to be a feasible adsorbent for copper recovery after the necessary scale-up studies.

• Journal of Environmental Science International
• /
• v.31 no.5
• /
• pp.413-422
• /
• 2022

To identify rice (Oryza sativa L.) cultivars suitable for Italian ryegrass (Lolium multiflorum Lam.)-rice double cropping systems, we investigated the yield and grain quality of four different midseason maturing rice cultivars ('Daebo', 'Haepum', 'Haiami', and 'Samdeog') and four midseason-to-late maturing rice cultivars ('Hyunpoom', 'Saeilmi', 'Saenuri', and 'Samkwang') in single rice cropping and Italian ryegrass-rice double cropping systems in paddy fields of Miryang, South Korea. We found that organic matter and available P₂O₅ content slightly decreased, whereas Na content increased, in the soil where Italian ryegrass was cultivated during winter compared to that in the soil that remained fallow during winter. The pH, electrical conductivity, organic matter, and contents of K⁺, Ca²⁺, Mg²⁺, and Na⁺ decreased, whereas the available P₂O₅ content slightly increased, in the soil where rice was harvested in both single and double cropping systems. However, compared to the optimum soil conditions for rice cultivation, available P₂O₅ and K⁺ content were high and Mg²⁺ content was low in both single and double cropping systems. At the heading stage, the culm length and leaf color slightly increased in most of the rice cultivars, whereas the panicle length and number slightly decreased, in the double cropped system. After harvesting, spikelet number and milled rice yield did not show a significant difference between single and double cropping systems. However, the ripened grain rate and weight per thousand grains increased slightly in the 'Saeilmi' and 'Samkwang' cultivars but remained either stable or slightly low in other cultivars in the double cropping system. The milled rice yield was high (> 500 kg/10a) in 'Daebo' and 'Haepum' among midseason maturing rice cultivars, and in 'Saeilmi' and 'Saenuri' among midseason-to-late maturing rice cultivars, in both single and double cropping systems. The head rice rate was high in midseason maturing rice cultivars in the double cropping systems, reaching > 70% in 'Haepum' and 'Haiami' cultivars, whereas it decreased in most midseason-to-late maturing rice cultivars (excluding 'Samkwang' cultivar), in double cropping systems. Particularly, it exceeded > 70% in the 'Saenuri' cultivar in both single and double cropping systems. The protein content in milled rice increased, whereas the amylose content either remained stable or slightly increased, in double cropping systems. The Toyo taste value decreased in all midseason-to-late maturing rice cultivars and slightly increased in the 'Daebo' and 'Haiami' cultivars among midseason maturing rice cultivars in double cropping systems. However, Toyo taste values in the 'Haepum', 'Haiami', and 'Saenuri' cultivars exceeding > 80% in both single and double cropping systems. Therefore, we recommend 'Haepum', 'Haiami', and 'Saenuri' cultivars as candidates for Italian ryegrass-rice double cropping systems due to high yield, head rice rate, and Toyo taste value.

• Journal of Wetlands Research
• /
• v.24 no.3
• /
• pp.204-212
• /
• 2022

The LID technique began to be applied in Korea after 2009, and LID facilities are installed and operated for rainwater management in business districts such as the Ministry of Environment, the Ministry of Land, Infrastructure and Transport, and LH Corporation, public institutions, commercial land, housing, parks, and schools. However, looking at domestic cases, the application cases and operation periods are insufficient compared to those outside the country, so appropriate design standards and measures for operation and maintenance are insufficient. In particular, LID facilities constructed using LID techniques need to maintain the environment inside LID facilities because hydrological and environmental effects are expressed by material circulation and energy flow. The LID facility is designed with the treatment capacity planned for the water circulation target, and the proper maintenance, vegetation, and soil conditions are periodically identified, and the efficiency is maintained as much as possible. In other words, the soil created in LID is a very important design element because LID facilities are expected to have effects such as water pollution reduction, flood reduction, water resource acquisition, and temperature reduction while increasing water storage and penetration capacity through water circulation construction. In order to maintain and manage the functions of LID facilities accurately, the current state of the facilities and the cycle of replacement and maintenance should be accurately known through various quantitative data such as soil contamination, snow removal effects, and vegetation criteria. This study was conducted to investigate the current status of LID facilities installed in Korea from 2009 to 2020, and analyze soil changes through the continuity and current status of LID facilities applied over the past 10 years after collecting soil samples from the soil layer. Through analysis of Saturn, organic matter, hardness, water contents, pH, electrical conductivity, and salt, some vegetation-type LID facilities more than 5 to 7 years after construction showed results corresponding to the lower grade of landscape design. Facilities below the lower level can be recognized as a point of time when maintenance is necessary in a state that may cause problems in soil permeability and vegetation growth. Accordingly, it was found that LID facilities should be managed through soil replacement and replacement.

• Tunnel and Underground Space
• /
• v.32 no.5
• /
• pp.285-297
• /
• 2022

We report results of Extended Leak-Off Test (XLOT) conducted in a large diameter borehole, which is drilled for installation of deep borehole geophysical monitoring system to monitor micro-earthquakes and fault behavior of major fault zones in the southeastern Korean Peninsula. The borehole was planned to secure a final diameter of 200 mm (or more) at a depth of ~1 km, with 12" diameter wellbore to intermediate depths, and 7-7/8" (~200 mm) to the bottom hole depth. We drilled first the 12" borehole to approximately 504 m deep and installed American Petroleum Institute standard 8-5/8" casing, then annulus between the casing and bedrock was fully cemented. XLOT was carried out for several purposes such as confirming casing and cementing integrity, measuring rock stress states. To that end, we drilled additional 4 m long open hole interval to directly inject water and pressurize into the rock mass using the upper API casings. During the XLOT, flow rates and interval pressures were recorded in real time. Based on the logs we tried to analyze hydraulic conductivity of the test interval.

• Journal of Korea Water Resources Association
• /
• v.56 no.2
• /
• pp.103-113
• /
• 2023

The river confluence is a section in which two rivers with different topographical and hyrodynamic characteristics are combined into one, and it is a section in which rapid flow, inflow of sediments, and hydrological topographic changes occur. In the confluence section, the flow of fluid occurs due to the difference in density due to the type of material or temperature difference, which is called a density flow. It is necessary to accurately measure and observe the confluence section including a certain section of the main stream and tributaries in order to understand the mixing behavior of the water body caused by the density difference. A comprehensive analysis of this water mixture can be obtained by obtaining flow field and flow rate information, but there is a limit to understanding the mixing of water bodies with different physical properties and water quality characteristics of rivers flowing with stratigraphic flow. Therefore, this study attempts to grasp the density flow through the water temperature distribution in the confluence section. Among the extensive data of the river, vertical data and water surface data were acquired, and through this, the stratification phenomenon of the confluence was to be confirmed. It was intended to analyze the mixed pattern of the confluence by analyzing the water mixing pattern according to the water temperature difference using the vertical data obtained by measuring the repair volume by installing the ADCP on the side of the boat and measuring the real-time concentration using YSI. This study can supplement the analysis results of the existing water quality measurement in two dimensions. Based on the comparative analysis, it will be used to investigate the current status of stratified sections in the water layer and identify the mixing characteristics of the downstream section of the river.