• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.193-198
• /
• 2021

In this study, the rheological characteristics and of 3D printing composite materials and the compressive strength characteristics according to the lamination patterns were evaluated. As a result of rheology test, rapid material change was observed after 60 minutes of extrusion, yielding stress 1.4 times higher than immediately after mixing, and plastic viscosity was 14.94-25.62% lower. The compressive strength of the specimens manufactured in the mold and the laminated specimens were compared, and the lamination pattern of the laminated specimens were 0°, 45°, and 90° as variables. The compressive strength of the mold casting specimen and the laminated specimen from 1 to 28 days of age showed similar performance regardless of the lamination pattern. In particular, at the age of 28 days, the modulus of elasticity, maximum compressive strength, and strain at maximum stress of all specimens were almost the same. In order to analyze the interface of the laminated specimens, X-ray CT analysis of the specimen whose compressive strength were measured was performed. Through CT analysis, it was confirmed that cracks did not occur at the lamination interface, which can be judged that the interface in the laminated specimen behaved in an integrated manner.

• Tunnel and Underground Space
• /
• v.32 no.6
• /
• pp.363-372
• /
• 2022

Precast concrete is an effective method to increase the construction quality and construction speed by optimizing and making the manufacturing conditions similar. In order to more effectively produce a fireproof material-integrated precast duct slab, the purpose of this study was to determine whether the fire resistance performance of the fireproof layer is maintained when a method of increasing the curing rate using a hardening accelerator is used. As a result of performing a fire resistance performance test on specimens classified according to whether or not the hardening accelerator was included, increase of temperature inside the specimen was high in the specimens using the hardening accelerator, and the section loss of the fireproof layer occurred locally on the surface exposed to fire heating. In conclusion, it is judged that the fireproof layer in the case where the strength at 3th day of age is gained within 1 day curing age using a hardening accelerator does not guarantee sufficient fire resistance performance in the conditions used in this study.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.32 no.2
• /
• pp.309-327
• /
• 2022

As ICT convergence is progressing in all industrial fields and creating the global ecosystem of the supply chain is accelerating, supply chain risk related with cyber area are also increasing. In particular. the supply chain of ICT products is very complex in terms of technical and environmental factors to be managed, so it is vert difficult to transparently manage the entire life cycle. Accordingly, the US, UK, and EU, etc. are conducting and establishing cyber supply chainsecurity-related research and policies for ICT product supply chains. Korea also has the plan to establish management system to secure the supply chain of major ICT equipment as a task in the basic plan of the national cybersecurity strategy announced in 2019, but there is no concrete policy yet. So, In this paper, we review the cyber supply chain security management system in the United States and present a supplementary way to the National Information Security Manual in Korea from the perspective of cyber supply chain security. It is expected that this will serve as a reference material for cyber supply chain measures that can be introduced in domestic information security field.

• Computers and Concrete
• /
• v.31 no.3
• /
• pp.267-276
• /
• 2023

The main purpose of the current research is to develop an efficient two variables trigonometric shear deformation beam theory to investigate the buckling behavior of symmetric and non-symmetric functionally graded carbon nanotubes reinforced composite (FG-CNTRC) beam resting on an elastic foundation with various boundary conditions. The proposed theory obviates the use to shear correction factors as it satisfies the parabolic variation of through-thickness shear stress distribution. The composite beam is made of a polymeric matrix reinforced by aligned and distributed single-walled carbon nanotubes (SWCNTs) with different patterns of reinforcement. The material properties of the FG-CNTRC beam are estimated by using the rule of mixture. The governing equilibrium equations are solved by using new analytical solutions based on the Galerkin method. The robustness and accuracy of the proposed analytical model are demonstrated by comparing its results with those available by other researchers in the existing literature. Moreover, a comprehensive parametric study is presented and discussed in detail to show the effects of CNTs volume fraction, distribution patterns of CNTs, boundary conditions, length-to-thickness ratio, and spring constant factors on the buckling response of FG-CNTRC beam. Some new referential results are reported for the first time, which will serve as a benchmark for future research.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.525-536
• /
• 2009

The current residential process adheres to a traditional method of construction involving wood framing on-site on poured concrete foundations which has been widely applied in North America. A conventional residential construction process can include seventeen distinct stages ranging from stake-out to pre-occupancy inspection. The current practice possesses short comings including high construction material wastes, long scheduling timelines, adverse weather conditions, poor quality, low efficiencies and negative environmental impacts from transportation and equipment use. Over CAN $5 billion dollars was spent in the construction sector during 2007 in Canada. Previous findings in CO₂ emissions during the construction process of a conventional dwelling emphasize more than 45 tonnes of CO₂ emissions. Hence, in Alberta alone during 2007, almost 50,000 residential units would release more than two million tonnes of CO₂. These numbers demonstrate the economical and environmental impact in building construction and its relationship with CO₂ emissions. The aim of this paper is to quantify the CO₂ emissions from the current residential construction process in order to establish the baseline for CO₂ emission reduction opportunities. The quantification collection methodology will be approached by identifying the seventeen various stages of construction and quantifying the contributions of CO₂ from specific activities and their impacts of work for each stage. The approach of separating these into separate stages for collection will allow for independent opportunities for analysis from various independent contractors from the entire scope of work. The use of BIM will be implemented to efficiently quantify CO₂ emissions. Based on the CO₂ quantification baseline, emission reduction opportunities such as an industrialized construction process will be introduced that allows homebuilders to reduce the environmental and economical impact of home construction while enabling them to produce higher quality, more energy efficient homes in a safer and shorter period of time.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.4
• /
• pp.62-69
• /
• 2023

This study investigated the electromechanical properties of cement based smart repair materials (SRMs) according to the different amounts of fine steel slag aggregates (FSSAs). SRMs can self-diagnose the quality of repairing and self-sense the damage of repaired zone. The replacement ratios of FSSAs to sand for SRMs were 0% (FSSA00), 25% (FSSA25), and 50% (FSSA50) by sand weight. The electrical resistivity of SRMs generally decreased as the compressive stress of SRMs increased: the electrical resistivity of FSSA25 at the age of 7 hours decreased from 78.16 to 63.68 kΩ-cm as the compressive stress increased from 0 to 22.37 MPa. As the replacement ratio of FSSAs by weight of sand increased from 0% to 25%, the stress sensitivity coefficient (SSC) of SRM at the age of 7 h increased from 0.471 to 0.828 %/MPa owing to the increased number of partially conductive paths in the SRMs. However, as the replacement ratio of FSSAs further increased up to 50%, the SSC decreased from 0.828 to 0.649 %/MPa because some of the partially conductive paths changed to continued conductive ones. SRMs are expected to self-sense the quality and future damage of repaired zone only by measuring the electrical resistivity of the repaired zone in addition to fast recovery in the mechanical resistance of structures.

• Journal of Korea Entertainment Industry Association
• /
• v.13 no.5
• /
• pp.73-82
• /
• 2019

The satirical content of the absurd play, centered on Lee Keun-sam's play, represents the family image of a modern capitalist society where only duty is emphasized while the characters are lost in love with the family. They show humans becoming subordinate to economic logic as traditional relationships and family relationships change into material ones due to the rapid development of the economy. The narrator expresses the roles of the performer and the narrator together. It also presents the plot as a characteristic element of epic and absurd dramas, and directs actors as directors. It also foretells the events that will take place in the future, presents the inner consciousness of the characters in the play, and reduces and expands events and times. In terms of conflict, in order to fulfill the financial responsibility of their children, the professor translates them like a machine and the wife distributes the money they earn as they demand. The middle-aged professor and his wife are not willing to make a difference in the real world, so specific conflicts are not revealed. Therefore, no concrete conflict appears within this work. The plot of consisted of 22 epicentre compartments, consisting of a time frame from evening to the next morning. And no special events happen and show only one family's daily life. In addition, materials that show simple repetition of daily life such as newspapers, rice, birthdays, etc. are effectively showing the character of absurdity through repeated structure. The linguistic features of the absurd play focus on expressing anxiety, despair, fantasy and the sense of loss that the object's purpose has disappeared. The stage system avoids detailed portrayals of naturalist plays and creates a thoroughly simplified image that the theme of the play demands, which shows that the stage unit is also an important element that characterizes the absurdity of reflexes.

• Tunnel and Underground Space
• /
• v.33 no.3
• /
• pp.169-188
• /
• 2023

Fires in tunnels are characterized by higher temperature rise and higher maximum temperatures compared to ground fires. For this reason, countries such as the Netherlands and Germany have developed separate temperature-time curves for use in tunnel fires. Fires in tunnels cause damage to the tunnel lining, such as loss of section and deterioration of the material properties. This study reviewed the design concept of fire stability of structures, section loss due to spalling, changes in physicochemical and mechanical properties of tunnel lining materials, fireproofing materials for structure safety, and fire damage prediction models. In order to secure the stability of a structure against fire, it is necessary to identify the type of structure and the possible fire load at the design stage, identify the expected section loss and damage range, and prepare for such damage through fireproofing materials. In this study, we have summarized the matters that can be referred to in performing such a series of tasks and presented our opinions on them.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.138-143
• /
• 2023

In this study, the crack healing performance of each crack healing agent manufacturing method was analyzed by adding crack healing agents in the form of alginate gel and spore suspension inoculated with endospores of calcium carbonate-forming bacteria to mortar. In addition, by applying it to an full-scale structure in the form of a box-type culvert, we attempted to create an environment in which the developed crack healing agent can be applied not only to a laboratory environment but also to an actual field. The crack healing agent using the dry heat drying method showed crack healing performance, but in the case of the freeze drying method, many spores were killed by freeze hardening and therefore the crack healing performance was lost. As a result of SEM and XRD pattern analysis of the presumed crack healing material extracted from the crack of a full-scale structure, it was found to be calcite, one of the calcium carbonate crystals produced by microorganisms applied to the crack healing agent. In conclusion, it was found that the crack healing by microorganisms can be implemented in a real structure.

• Korean Journal of Environmental Agriculture
• /
• v.13 no.2
• /
• pp.223-230
• /
• 1994

A practical study on a drying and fermentation system equipped with a stirring machine operated mechanically, of pig manure was conducted to prove the efficiency of and practicability to an ordinary pig farm. The type of the drying bed was a round-shaped (r=3m) concrete structure and the stirring machine was adopted to stir and transfer dried pig manure to the fermentation tank. The dried pig manure was put into a fermentation tank ($V=18m^3$), which was aerated from pipe lines installed at the bottom. While water content of pig manure passing through a drying bed was remarkably reduced than before drying, the drying efficiency of this system decreased in winter. However, the temperature of pig manure piled up in the fermentation room in winter reached over $60^{\circ}C$ and excess water of pig manure was removed during the fermentation process. The reduction rate of water content of pig manure, to which dried pig manure was added as bulking material on the drying bed, was 52.1%, but when dried without bulking material it was only 19.7%. Although the content of $P_2O_5$ of dried pig manure was slightly higher than that of fresh pig manure, progressive changes in chemical composition between fresh and dried pig manure made no great difference. Among the contents of minerals of fresh and dried pig manure, CaO was the highest and the rest were in the decreasing order of $K_2O$, MgO, and $Na_2O$. Population density of E. coli and Streptococci of dried pig manure was reduced by 142 and 236 times that of fresh pig manure, respectively. The installation cost of this drying and fermentation system was 4,185,630 won (approximately 5,232 US $) and operating cost per year was 190,000 won (237.5US $) on the basis of self-labor condition.