• Steel and Composite Structures
• /
• 제27권4호
• /
• pp.509-523
• /
• 2018

This paper presents experimental results on the residual bond-slip behavior of high strength concrete-filled square steel tube (HSCFST) after elevated temperatures. Three parameters were considered in this test: (a) temperature (i.e., $20^{\circ}C$, $200^{\circ}C$, $400^{\circ}C$, $600^{\circ}C$, $800^{\circ}C$); (b) concrete strength (i.e., C60, C70, C80); (c) anchorage length (i.e., 250 mm, 400 mm). A total of 17 HSCFST specimens were designed for push-out test after elevated temperatures. The load-slip curves at the loading end and free end were obtained, in addition, the distribution of steel tube strain and the bond stress along the anchorage length were analyzed. Test results show that the shape of load-slip curves at loading ends and free ends are similar. With the temperature constantly increasing, the bond strength of HSCFST increases first and then decreases; furthermore, the bond strength of HSCFCT proportionally increases with the anchoring length growing. Additionally, the higher the temperature is, the smaller and lower the bond damage develops. The energy dissipation capacity enhances with the concrete strength rasing, while, decreases with the temperature growing. What is more, the strain and stress of steel tubes are exponentially distributed, and decrease from the free end to loading end. According to experimental findings, constitutive formula of the bond slip of HSCFST experienced elevated temperatures is proposed, which fills well with test data.

• Structural Engineering and Mechanics
• /
• 제77권5호
• /
• pp.673-689
• /
• 2021

This paper addresses the efficiency of thermal insulation layers applied to protect structural elements strengthened by fiber-reinforced polymers (FRP) in the case of fire event. The paper presents numerical modeling and nonlinear analysis of reinforced concrete (RC) columns externally strengthened by FRP and protected by thermal insulation layers when subjected to elevated temperature specified by standard fire tests, in order to predict their residual capacity and fire endurance. The adopted numerical approach uses commercial software includes heat transfer, variation of thermal and mechanical properties of concrete, steel reinforcement, FRP and insulation material with elevated temperature. The numerical results show good agreement with published results of full-scale fire tests. A parametric study was conducted to investigate the influence of several variables on the structural response and residual capacity of insulated FRP-confined columns loaded by service loads when exposed to fire. The residual capacity of FRP-confined RC column was affected by concrete grade and insulation material and was shown to improve substantially by increasing the concrete cover and insulation layer thickness. By increasing the VG insulation layer thickness 15, 32, 44, 57 mm, the loss in column capacity after 5 hours of fire was 30%, 13%, 7% and 5%, respectively. The obtained results demonstrate the validity of the presented approach for estimation of fire endurance and residual strength, as an alternative for fire testing, and for design of fire protection layers for FRP-confined RC columns.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.220-221
• /
• 2017

In this study, the thermal strain of high strength concrete with the compressive strength of 70, 80, 100MPa were measured under 33% of compressive strength loading condition. As results, it is considered that shrinkage strain of high strength concrete become grater at the elevated temperatures.

• 콘크리트학회논문집
• /
• 제13권3호
• /
• pp.268-276
• /
• 2001

본 논문은 고온에서의 콘크리트 재료모델을 연구하였다. 콘크리트 응력-변형률 곡선은 온도가 증가함에 따라 그 형태가 변한다. 온도에 따른 콘크리트 재료거동의 변화를 나타내기 위하여 변형된 Saenz 제안식을 이용하여 응력-변형률 관계를 표시하였다. 고온에서의 급격한 변형률의 증가현상을 설명하기 위하여, 콘크리트의 변형률 성분을 순수 열팽창 변형률, 열적크리프 변형률, 과도 변형률 및 역학적 변형률로 구분하여 나타내었다. 열적크리프 변형률은 Baily-Norton의 장기크리프 곡선 식을 수정.제안하여 1축 실험 결과를 온도, 시간 및 응력의 함수로 표현하였고, 또한 유효응력 및 유효변형률 개념을 도입하여 다차원에서도 적용할 수 있는 모델을 제시하였다. 과도 변형률을 제안하여 다공탄성 거동을 가정한 콘크리트 내에 포함된 공극 및 수분의 작용을 역학적 거동의 영향을 분석하고자 하였다. 마지막으로, 본 논문에서 제시한 고온에서의 콘크리트 재료모델을 이용한 해석결과를 실제 화재실험자료와 비교하였다.

• Advances in concrete construction
• /
• 제10권5호
• /
• pp.443-454
• /
• 2020

In recent years, many studies have been done on the performance of concrete containing glass powder (GP). For the purpose of widespread use of GP in concrete mixes, a knowledge of the performance of such a mixture after a fire is essential for the perspective of structural use. This research work was carried out to evaluate the performance of High Performance Concrete (HPC) made with GP after being exposed to elevated temperature. The studied mixtures include partial replacement of cement by GP with up to 30%. The mechanical performance and structural alterations were assessed after high temperature treatment from 200℃ to 800℃. The mechanical performance was evaluated by testing the specimens to the compressive and tensile strength. In addition, the mass loss and the porosity were measured to notice the structural alterations. Changes in microstructure due to temperature was also investigated by the X-ray diffraction (XRD) and thermal gravimetric analyses (TGA) as well as porosity adsorption tests. The results of the concrete strength tests showed a slight difference in compressive strength and the same tensile strength performance when replacing a part of the cement by GP. However, after high temperature exposition, concrete with GP showed better performance than the reference concrete for temperature below 600℃. But, after heating at 800℃, the strength of the concrete with GP drop slightly more than reference concrete. This is accompanied by an important increase in mass loss and water porosity. After the microstructure analysis, no important changes happened differently for concrete with GP at high temperature except a new calcium silica form appears after the 800℃ heating.

• 국제초고층학회논문집
• /
• 제10권4호
• /
• pp.335-344
• /
• 2021

In structural engineering practice, understanding the performance of composite columns under extreme loading conditions such as high-rise bulding, long span and heavy loads is essential to accuratly predicting of material responses under severe loads such as fires or earthquakes. Hitherto, the combined effect of partial axial loads and subsequent elevated temperatures on the performance of hollow steel column filled fly ash concrete have not been widely investigated. Comprehensive test was carried out to investigate the effect of elevated temperatures on partial axially loaded square hollow steel column filled fly ash concrete as reported in this paper. Four batches of hollow steel column filled fly ash concrete ( 30 percent replacement of fly ash), (HySC) and normal concrete (CFHS) were subjected to four different load levels, n_f of 20%, 30%, 40% and 50% based on ultimate column strength. Subsequently, all batches of the partially damage composite columns were exposed to transient elevated temperature up to 250℃, 450℃ and 650℃ for one hour. The overall stress - strain relationship for both types of composited columns with different concrete fillers were presented for each different partial load levels and elevated temperature exposure. Results show that CFHS column has better performance than HySC at ambient temperature with 1.03 relative difference. However, the residual ultimate compressive strength of HySC subjected to partial axial load and elevated temperature exposure present an improvement compared to CFHS column with percentage difference in range 1.9% to 18.3%. Most of HySC and CFHS column specimens failed due to local buckling at the top and middle section of the column caused by concrete crushing. The columns failed due to global buckling after prolong compression load. After the compression load was lengthened, the columns were found to fail due to global buckling except for HySC02.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.133-134
• /
• 2021

Limestone-calcined clay-Cement (LC3) concrete provides a solution for sustainability, durability, and profitability of concrete industry. This study shows experimental studies of the macro properties (residual compressive strength), the meso properties (mesoscopic images), and micro properties (thermogravimetric (TG) analysis, X-ray powder diffraction (XRD), FTIR spectra, Raman spectra, Mercury intrusion porosimetry, and SEM) of LC3 paste with various mixtures and at high elevated temperatures (20 ℃, 300 ℃, 550 ℃ and 900 ℃). We find (1) Regarding to macro properties, LC3 cementitious materials are at a disadvantage in compressive strength when the temperature is higher than 300 ℃. (2) Regarding to meso properties, when the temperature reached 550 ℃, all samples generated more meso cracks. (3) Regarding to micro properties, first, as the substitution amount increases, its CH content decreases significantly; second, at 900 ℃, for samples with calcined clay, a large amount of gehlenite crystalline phase was found; third, at elevated temperatures (20 ℃, 300 ℃, 550 ℃ and 900 ℃), there is a linear relationship between the residual compressive strength and the cumulative pore volume; fourth, at 900 ℃, a large amount of dicalcium silicate was generated, and damage cracks were more pronounced. The experimental results of this study are valuable of material design of fire resistance of LC3 concrete.

• Steel and Composite Structures
• /
• 제32권5호
• /
• pp.559-569
• /
• 2019

The bond strength between composite laminates and concrete is a key factor that controls the behavior of concrete members strengthened with fiber reinforced polymer (FRP) sheets, which can be affected by several parameters such as thermal stresses and surface preparation. This article presents the result of an experimental study on the bond strength between FRP sheets and concrete at ambient temperature after specimens had been exposed to elevated temperatures of up to $200^{\circ}C$. For this purpose, 30 specimens of plain concrete with dimensions of $150{\times}150{\times}350mm$ were prepared. Three different conventional surface preparation methods (sandblasting, wire brushing and hole drilling) were considered and compared with a new efficient method (fiber implantation). Deformation field during each experiment was monitored using particle image velocimetry. The results showed that, the specimens which were prepared by conventional surface preparation methods, preserved their bond integrity when exposed to temperature below glass transition temperature of epoxy resin (about $60^{\circ}C$). Beyond this temperature, the bond strength and stiffness decreased significantly (about 50%) in comparison with control specimens. However, the specimens prepared by the proposed method displayed higher bond strengths of up to 32% and 90% at $25^{\circ}C$ and $200^{\circ}C$, respectively.

• Corrosion Science and Technology
• /
• 제6권6호
• /
• pp.269-274
• /
• 2007

The corrosion of steel in concrete is significant in marine environment. Salt damage is one of the most detrimental causes to concrete bridges and port structures. Especially, the splash and tidal zones around water line are comparatively important in terms of safety and life-time point of view. During the last several decades, cathodic protection (cp) has been commonly accepted as an effective technique for corrosion control in concrete structures. Zn-mesh sacrificial anode has been recently developed and started to apply to the bridge column cp in marine condition. The detailed parameters regarding Zn-mesh cp technique, however, have not well understood so far. This study is to investigate how much Zn-mesh cp influences along the concrete column at elevated temperature. About 100 cm column specimens with eight of 10 cm segment rebars have been used to measure the variation of cp potential with the distance from Zn-mesh anode at both $10^{\circ}C$ and $40^{\circ}C$ in natural seawater. The cp potential change and current diminishment along the column specimens have been discussed for the optimum design of cp by Zn-mesh sacrificial anode.

• 콘크리트학회논문집
• /
• 제23권6호
• /
• pp.723-730
• /
• 2011

콘크리트 중의 골재가 차지하는 비율은 약 70~80 vol%로서 콘크리트의 고온 역학적 성상에 큰 영향요소로 작용할 수 있다. 이 연구는 고온시 콘크리트의 역학적 특성을 평가하기 위한 일환으로써 다양한 환경조건, 즉 고온조건, 하중조건에 따른 역학적 특성을 비교하기 위하여 목표강도 60 MPa급 보통 골재 및 경량 골재 콘크리트를 대상으로 선정하였다. 사용된 시험체는 ${\phi}100{\times}200mm$로서 상온 압축강도의 0%, 20%, 40% 하중을 재하한 상태에서 고온에 따른 강도, 탄성계수, 열팽창 변형(thermal strain), 전체 변형(total strain), 내력저하수축(transient creep) 등 고온에서의 역학적 특성을 평가하였다. 시험 결과 골재의 열팽창계수가 작은 경량 콘크리트는 열팽창 변형이 일반 골재를 사용한 콘크리트에 비하여 전반적으로 작게 나타났으며, 고온조건인 $700^{\circ}C$에서도 압축강도 저하가 상온강도에 대하여 80% 수준으로 나타났다. 또한 재하에 의한 내력저하수축은 $500^{\circ}C$를 기준으로 콘크리트의 변형을 팽창에서 수축으로 전환시키는 영향요인으로써, 콘크리트와 골재의 열팽창 변형비(concrete /aggregate)가 수축의 경향이 큰 경우 콘크리트의 내력저하가 적은 경향을 확인할 수 있었다.