• Design & Manufacturing
• /
• v.18 no.2
• /
• pp.1-8
• /
• 2024

Unlike the roll-to-roll process that uses a steel roll and a nip roll, a vacuum roll can hold and transfer a thin film using a single roll. To precisely manufacture a vacuum roll, a thin outer cylinder must be machined, which is assembled on the outside of the roll and contacts the film via vacuum pressure. In this study, the effects of jaw width and chucking force on the deformation of the outer cylinder during the turning process were investigated using analysis, and a precision machining and burr removal process was developed. The deformation of the outer cylinder decreased almost linearly with increasing jaw width and increased with higher chucking force and larger cylinder diameter. Additionally, the deflection due to the weight of the outer cylinder was approximately three times greater than that caused by film tension. For the machined outer cylinder, a burr removal experiment was conducted, and concentricity and cylindricity were measured. Using a device that removes burrs by rotating a wheel connected to the main shaft at high speed, it was found that burrs generated on the inner diameter could be removed very efficiently. On the vacuum side, the concentricity errors of the inner and outer diameters were 0.015 mm and 0.014 mm, respectively, and on the opposite side, they were 0.006 mm and 0.010 mm, respectively. Additionally, the measurement of Total Indicator Runout (TIR) according to the angle showed that the maximum cylindricity of the outer and inner diameters was 0.02 mm and 0.025 mm, respectively. Finally, through burr-height measurement at the hole boundary, it was found that the heights were within 0.05 mm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.19-22
• /
• 2005

As the optical communication industry is developed, the demand of optical communication part is increasing. $ZrO_2$ ceramic ferrule is very important part which can determines the transmission efficiency and information quality to connect the optical fibers. In general $ZrO_2$ ceramic ferrule is manufactured by grinding process because the demands precision is very high. And the co-axle grinding process of $ZrO_2$ ceramic ferrule is to make its concentricity all of uniform before centerless grinding. When co-axle grinding of ferrule supported by two pin, pin chucking alignment accuracy is very important. This paper deals with the analysis of the chucking alignment experiment with parallel error on the micro feeding equipment. Thus, if possible be finding highly good the chucking alignment of two pin.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.63-68
• /
• 2000

We present an automatic inspection system which been developed to evaluate the geometric tolerances of the optical fiber connectors with an dimensional accuracy of$\pm0.1\mnm$. The main part of the inspection system comprises a series of machine vision and laser scanning probes to measure the internal and external circle diameters along with concentricity by making the most of advanced edge detection algorithms. Actual experimental results obtained through various repeatability tests demonstrate that the system well satisfies the required industrial demands for in-situ inspection of optical fiber connections in real manufacturing environment.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.7-12
• /
• 2003

각광을 받고 있는 광통신 분야의 핵심부품인 페룰은 일본이 전 세계의 95%를 장악하고 있다. 국내에서도 일부 업체에서 양산을 하고 있으나, 핵심 연삭공정에 사용되는 연삭 가공장비는 전량 수입되고 있는 실정이다. 페룰은 0.1∼0.3$\mu\textrm{m}$의 동심도, ${\pm}$ 0.2$\mu\textrm{m}$의 외경치수, 0.1$\mu\textrm{m}$대의 진원도와 원통도, 10nm의 표면 거칠기를 구현해야 세계적 경쟁력을 갖출 수 있는 초미세, 초정밀 기계가공 부품이다.(중략)

• Journal of Korea Multimedia Society
• /
• v.10 no.6
• /
• pp.699-706
• /
• 2007

This article is an approach to improving the clustering of Web images by using high-level semantic features from text information relevant to Web images as well as low-level visual features of image itself. These high-level text features can be obtained from image URLs and file names, page titles, hyperlinks, and surrounding text. As a clustering algorithm, a self-organizing map (SOM) proposed by Kohonen is used. To evaluate the clustering efficiencies of SOMs, we propose a simple but effective measure indicating the accumulativeness of same class images and the perplexities of class distributions. Our approach is to advance the existing measures through defining and using new measures accumulativeness on the most superior clustering node and concentricity to evaluate clustering efficiencies of SOMs. The experimental results show that the high-level text features are more useful in SOM-based Web image clustering.

• Transactions of Materials Processing
• /
• v.7 no.4
• /
• pp.393-399
• /
• 1998

For minimizing wall thickness thinning of circular shells, a new stamping technology, the deep draw-ing process combined with ironing is approached and investigated. The design requirements for the deep drawing shells are to keep the optimum wall thickness with max. 10 percent thickness thinning of the initial blank thickness, to make uniform thickness strain distribution for the wall of circular shell and to improve the shape accuracy for the roundness and concentricity. In order to check the validity and effectiveness of proposed work, a sample process design is applied to a circular shell needed for a 4multi-stepped deep drawing. Through experiments, the variations of the thickness strain distribution in each drawing process are observed. Also a series of experiments are performed to investigate optimum process variables such as the geometry of tooling, radius and drawing rate. In particular, the advantage of current approach with ironing is shown in contrast to the conventional deep drawing process. From the results of proposed method, the optimum value of process variables are obtained, which contribute more uniform thickness strain distribution and better quality in the drawn product.

• Journal of the Korean Institute of Navigation
• /
• v.13 no.1
• /
• pp.11-20
• /
• 1989

Radar image data were collected through the on-line data acquisition system of A/D converter and personal computer, and the image was restorated on CRT or plotter after digital image processing of the data. The digital image processing system which was developed for this study, consisted of some kinds of software as follows : rearrangement, transformation, and enhancement of the image data in real space or frequency space by Fourier transform, edge detection of the image, compact processing, state inferential processing, and so on. Since the image of PPI radar sweeps from the center to the circumference of a circle, the image within a given period has the shape of fan. Therefore the acquired data were transformed to have the same interval as that of data in outmost concentricity. The results of various image processing methods using transformed data were better than those of the methods using original data.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.41-47
• /
• 2009

This research deals with evaluation of machining accuracy for Parallel Kinematic Machine Tool(PKMT) applied parallel type robot system with high precision and stiffness. For this purpose, machine simulation is carried out to foreknow collision and interference between workpiece and tool. Furthermore, on the basis of machine simulation data, PKMT is manufactured. Machining accuracy such as cylindricity straightness, squareness, parallelism circularity, concentricity pitch error and yaw error, is measured by using coordinate measuring machine. Test piece for evaluation of machining accuracy is designed and manufactured under the standard of ISO 10791-7.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.1-8
• /
• 2017

This paper concerns the possibility of 3D printing reverse idle gears for tractor transmission. For the purposes of this experiment, idle gears were manufactured using a SLA 3D printer, FDM 3D printer, and through machining. The accuracy of the idle gears produced in these three different ways were evaluated by the properties of their outer diameter, inner diameter, roundness, concentricity, parallelism, span, backlash, and gear grade. The tooth characteristics of the idle gears were evaluated by their profile, lead, and the pitch of the gears. The results of this experiment determined that the surface conditions created by the finishing process had a significant impact on the dimensional accuracy of the gears and the characteristics of their teeth.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.31-31
• /
• 2004

차세대 정보통신 네트워크는 기하급수적으로 급증하는 트래픽 수요와 고속 및 대용량화는 서비스 형태에 따라 인터넷화 및 광통신화로 발전되고 있으며, 사용자들의 요구 통신 속도 또한 크게 증가하고 있어 2005-2010년경에는 인터넷 노드 하나가 처리해야 할 트래픽은 10-100Tbps가 될 전망이며 이를 수용, 교환처리, 전달하기 위한 방법으로 광통신 이외에는 기술적인 대안을 찾기 힘든 실정이다. 한국의 경우 세계최고의 광통신망 구축에 따라 광페룰의 기반 수요가 크게 기대되고 있으며, 전 세계적인 광통신망 구축계획(2005∼2007년, 초고속정보통신망 Fiber to the Home)에 따라 한국의 광통신 인프라에 대한 전세계의 관심이 고조되고 있다.(중략)