• 한국자기학회지
• /
• 제23권3호
• /
• pp.89-93
• /
• 2013

본 연구에서는 홀센서의 감도를 높이기 위해 사용되는 자속집속기의 두께, 홀소자와의 상대적 위치, 모서리 형상에 따르는 발생 자계를 유한요소법을 이용하여 계산하였다. 자속집속기의 두께가 얇을수록 발생 자계가 커지는 것을 알 수 있었고, 이 경향은 반자계를 고려한 겉보기 상대투자율의 두께의존성과 유사하다는 것을 알 수 있었다. 홀소자와의 상대적 위치에 따라 최대의 자계를 발생시키는 자속집속기의 최적의 두께가 변화하는 것을 알 수 있었다. 자속집속기와 홀소자의 간격이 가까울 경우, 자속집속기의 모서리 형상에 경사가 없는 것이 유리하지만, 자속집속기와 홀소자의 간격이 멀어질수록 자속집속기의 모서리를 경사지게 하는 것이 유리하다는 것을 알 수 있었다.

• Wind and Structures
• /
• 제38권2호
• /
• pp.109-118
• /
• 2024

A solar concentrator is a reflective surface in the shape of a parabola that collects solar rays in a focal area. This concentrator follows the path of the sun during the day with the help of a tracking system. One of the most important issues in the design and construction of these reflectors is the force exerted by the wind. This force can sometimes disrupt the stability of the concentrator and overturn the entire system. One of the ways to estimate the force is to use the numerical solution of the air flow in three dimensions around the dish. Ansys Fluent simulation software has been used for modeling several angles of attack between 0 and 180 with respect to the horizon. From the comparison of the velocity vector lines on the dish at angles of 90 to - 90 degrees, it was found that the flow lines are more concentrated inside the dish and there is a tendency for the flow to escape around in the radial direction, which indicates the presence of more pressure distribution inside the dish. It was observed that the pressure on the concave surface was higher than the convex one. Then, the effect of adding a hole with various diameter of 200, 300, 400, 500, and 600 mm on the dish was investigated. By increasing the diameter up to the optimized size of 400 mm, a decrease in the maximum pressure value in the pressure distribution was shown inside the dish. This pressure drop decreased the drag coefficient. The effect of the hole on the dish was also investigated for the 30-degree angled dish, and it was found that the results of the 90-degree case should be considered as the basis of the design.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.1283-1287
• /
• 2009

In this study, an analysis was performed on an evaporative steam generator (concentrator), where natural circulation convective boiling occurs on tube-side by condensing hot steam on shell-side. Existing correlations on two-phase pressure drop, boiling or condensation heat transfer were used for the analysis. The effect of number of tubes, tube length, etc. on thermal performance was investigated. Simulation results reveal that steam generation rate increases almost proportionally to the tube length, or number of tubes. It is also shown that water circulation rate decreases as tube length increases.

• 한국태양에너지학회 논문집
• /
• 제37권1호
• /
• pp.39-45
• /
• 2017

This paper presents the effect of solar collectors on the performance of solar tracking daylighting systems. A series of measurements were made for two different types of solar collectors mounted on double axis solar trackers: Parabolic dish concentrator and Fresnel Lens. Indoor light levels were measured at different locations of an office space (longitude: 126.33 E, latitude 33.45 N) as photo sensors were placed on a task plane 80 cm above the floor. To accurately monitor the applicability of the systems, measurements were performed under clear and overcast sky conditions with the roll-screen (on the south window) in the down position. Comparing the illuminance data, the system with Fresnel lens outperformed that of parabolic dish concentrator. On clear days, the former delivered the light levels of 400~600 lux on the task plane whereas the latter recorded 100~200 lux. Depending on the amount of cloud cover, on overcast days, illuminance readings fluctuated to some extent.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.50-56
• /
• 2004

MlAB(magnetically impelled arc butt) welding is a sort of pressure welding method by melting two pipe sections with high speed rotating arc and upsetting two pipes in the axial direction. The electro-magnetic force, the driving force of the arc rotation, is generated by interaction of arc current and magnetic field induced from the magnetic flux generator in the welding system. In this study, an openable coil system for the generation of magnetic flux and a 3-dimensional numerical model for analyzing the electro-magnetic field were proposed. Through the fundamental numerical analyses, a magnetic concentrator was adopted for smoothing the magnetic flux density distribution in the circumferential direction. And then a series of numerical analysis were performed for investigating the effect of system parameters on the magnetic flux density distribution in the interested welding area.. Numerical quantitative analyses showed that magnetic flux density distribution generated from the proposed coil system is mainly dependent on the exciting current in the coil and the position of coil or concentrator from the pipe outer surface. And the gap between pipe ends and arc current are also considered as important factors on arc rotating behavior.

• 에너지공학
• /
• 제21권2호
• /
• pp.124-132
• /
• 2012

본 연구에서는 북측창을 가진 강의실 내의 불균형적인 실내 조도차이를 개선하기 위해 두 가지의 자연채광시스템을 적용하였을 경우에 대하여 Photopia를 이용한 성능 시뮬레이션을 수행하였다. 특히, 본 연구에서는 태양고도가 최고 $80^{\circ}$ 이르는 하지에 청천공 상태 하에서의 태양고도에 따른 각 시스템의 배광분포곡선을 구하고 이를 이용하여 실내 조도 등을 분석하였다. 작업면의 경우, 창측과 복도측의 평균 조도차가 1000lx를 초과하였는데 시스템 설치 후에는 그 차이가 상당히 줄어드는 것으로 나타났다. 광튜브 시스템 설치시 906lx에서 603lx로 감소하였으며, 디쉬형 시스템은 308lx까지 줄어들었다. 광튜브의 성능은 태양고도에 영향을 크게 받았으며 디쉬형 집광기는 지속적인 태양추적으로 인하여 태양고도에 관계없이 일정한 성능을 보여주었다.

• Wind and Structures
• /
• 제27권1호
• /
• pp.41-57
• /
• 2018

Concentrated Solar Photovoltaic (CPV) is a promising alternative to conventional solar structures. These solar tracking structures need to be optimized to be competitive against other types of energy production. In particular, the selection of the structural parameters needs to be optimized with regards to the dynamic wind response. This study aims to evaluate the effect of the main structural parameters, as selected in the preliminary design phase, on the wind response and then on the weight of the steel support structure. A parametric study has been performed where parameters influencing dynamic wind response are varied. The study is performed using a semi-deterministic time-domain wind analysis method. Unsteady aerodynamic model is applied for the shape of the CPV structure collector at different configurations in conjunction with a consistent mass-spring-damper model with the corresponding degrees of freedom to describe the dynamic response of the system. It is shown that, unlike the static response analysis, the variation of the peak wind response with many structural parameters is highly nonlinear because of the dynamic wind action. A steel structural optimization process reveals that close attention to structural and site wind parameters could lead to optimal design of CPV steel support structure.

• 신재생에너지
• /
• 제4권4호
• /
• pp.17-22
• /
• 2008

A low concentrating (< 5X) photovoltaic module with aluminum reflectors is fabricated and evaluated which is designed to reduce the affection of the high temperature to the solar cell modules preventing the efficiency lowering. As results, the output power is increased of 1.97X from the concentrating photovoltaic module which is designed with the concentrating ratio of 2.25X and to control the module temperature cooling the module by air circulation. Also, the effect of the concentrating module with aluminum reflectors on the conventional PV module is investigated at the field. The result shows the increase of the output power more than about 20% and the improvement of the module efficiency of 1.4X in spite of the increase of average module temperature.

• 한국유체기계학회 논문집
• /
• 제14권4호
• /
• pp.64-69
• /
• 2011

Integrating wind energy systems into building design is a small but growing trend, and high riese with their elevated wind speeds seem particularly suited to the technology. This paper deal with building-integrated wind turbine design. It thus contains two topics: wind energy and building design. Several building-integerated wind turbine design have been categorized and reviewed.

• 한국태양에너지학회 논문집
• /
• 제24권4호
• /
• pp.19-25
• /
• 2004

A numerical study is performed to investigate the effect of sun tracking on the thermal performance of the evacuated compound parabolic concentrator (CPC) collectors. The evacuated CPC collectors consist of a two-layered glass tube, a copper tube and a reflector. The collector has a copper tube as an absorber and a reflector inside a glass tube. The water is used as a working fluid. The length and the diameter of the glass tube are 1,700mm and 70mm, respectively. The length and the diameter of the copper tube are 1,700mm and 25.4mm, respectively. Ray tracing analysis is carried out in order to compare absorbed heat fluxes on the absorber surface of the stationary and tracking collectors. The collected energy is calculated and compared with that on a fixed surface tilted at $35^{\circ}$ on the ground and facing south. The results indicate that the collected solar energy of the sun tracking system is significantly larger than that of a stationary collector. The sun tracking evacuated CPC collectors show a better performance with an increase in the thermal efficiency of up to 14% compared with an identical stationary collector.