• Journal of KIISE:Computer Systems and Theory
• /
• v.30 no.9
• /
• pp.512-522
• /
• 2003

For a time-multiplexed FPGA, a circuit is partitioned into several subcircuits, so that they temporally share the same physical FPGA device by hardware reconfiguration. In these architectures, all the hardware reconfiguration information called contexts are generated and downloaded into the chip, and then the pre-scheduled context switches occur properly and timely. Typically, the size of the chip required to implement the circuit depends on both the maximum number of the LUT blocks required to implement the function of each subcircuit and the maximum number of micro-registers to store results over context switches in the same time. Therefore, many partitioning or synthesis methods try to minimize these two factors. In this paper, we present a new estimation technique to find the lower bound on the number of micro-registers which can be obtained by any synthesis methods, respectively, without performing any actual synthesis and/or design space exploration. The lower bound estimation is very important in sense that it greatly helps to evaluate the results of the previous work and even the future work. If the estimated lower bound exactly matches the actual number in the actual design result, we can say that the result is guaranteed to be optimal. In contrast, if they do not match, the following two cases are expected: we might estimate a better (more exact) lower bound or we find a new synthesis result better than those of the previous work. Our experimental results show that there are some differences between the numbers of micro-registers and our estimated lower bounds. One reason for these differences seems that our estimation tries to estimate the result with the minimum micro-registers among all the possible candidates, regardless of usage of other resources such as LUTs, while the previous work takes into account both LUTs and micro-registers. In addition, it implies that our method may have some limitation on exact estimation due to the complexity of the problem itself in sense that it is much more complicated than LUT estimation and thus needs more improvement, and/or there may exist some other synthesis results better than those of the previous work.

• The KIPS Transactions:PartD
• /
• v.10D no.7
• /
• pp.1149-1154
• /
• 2003

Due to various requirements for the user access control to large databases in the hospitals and the banks, database security has been emphasized. There are many security models for database systems using wide variety of policy-based access control methods. However, they are not functionally enough to meet the requirements for the complicated and various types of access control. In this paper, we propose a database security system that can individually control user access to data groups of various sites and is suitable for the situation where the user's access privilege to arbitrary data is changed frequently. Data group(s) in different sixes d is defined by the table name(s), attribute(s) and/or record key(s), and the access privilege is defined by security levels, roles and polices. The proposed system operates in two phases. The first phase is composed of a modified MAC (Mandatory Access Control) model and RBAC (Role-Based Access Control) model. A user can access any data that has lower or equal security levels, and that is accessible by the roles to which the user is assigned. All types of access mode are controlled in this phase. In the second phase, a modified DAC(Discretionary Access Control) model is applied to re-control the 'read' mode by filtering out the non-accessible data from the result obtained at the first phase. For this purpose, we also defined the user group s that can be characterized by security levels, roles or any partition of users. The policies represented in the form of Block(s, d, r) were also defined and used to control access to any data or data group(s) that is not permitted in 'read ' mode. With this proposed security system, more complicated 'read' access to various data sizes for individual users can be flexibly controlled, while other access mode can be controlled as usual. An implementation example for a database system that manages specimen and clinical information is presented.

• Journal of radiological science and technology
• /
• v.32 no.3
• /
• pp.325-334
• /
• 2009

Purpose : This study was conducted to assess how effective the permeability ratio and relative cerebral blood volume ratio are to tumor through perfusion MRI by measuring and reflecting the grade assessment and differential diagnosis and the permeability and relative cerebral blood volume of contrast media plunged from blood vessel into organ due to breakdown of blood-brain barrier in cerebral. Subject and Method : Subject of study was 29 patients whose diagnosis were confirmed by biopsy after surgery and 550 (11 slice$\times$50 image) perfusion MRI were used to make image of relative cerebral blood volume with the program furnished on instrument. The other method was to transmit to private computer and the image analysis was made additionally by making image of relative cerebral blood volume-reformulated singular value decomposition, rCBV-rSVD and permeability using IDL.6.2. In addition, Kruskal-wallis test tonggyein non numerical average by a comparative analysis of brain tumors Results : The rCBV ratio (Functool PF; GE Medical Systems and IDL 6.2 program by analysis) and permeability ratio of tumors were as follows; high grade glioma(n=4), (14.75, 19.25) 13.13. low grade astrocytoma(n=5) (14.80, 15.90) 11.60, glioblastoma(n=5) (10.90, 18.60), 22.00, metastasis(n=6) (11.00, 15.08). 22.33. meningioma(n=6) (18.58, 7.67), 5.58. oliogodendroglioma(n=3) (23.33, 16.33, 15.67. Conclusion : It was not easy to classify the grade with the relative cerebral blood volume ratio measured by using the relative cerebral blood image by type of tumors, however, permeability ratio measured by permeability image revealed that the higher the grade of tumor, the higher the measured permeability ratio, showing the assessment of tumor grade is more effective to differential diagnosis.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.35-61
• /
• 1978

To find out the power tiller's travel and tractive characteristics on the general slope land, the tractive p:nver transmitting system was divided into the internal an,~ external power transmission systems. The performance of power tiller's engine which is the initial unit of internal transmission system was tested. In addition, the mathematical model for the tractive force of driving wheel which is the initial unit of external transmission system, was derived by energy and force balance. An analytical solution of performed for tractive forces was determined by use of the model through the digital computer programme. To justify the reliability of the theoretical value, the draft force was measured by the strain gauge system on the general slope land and compared with theoretical values. The results of the analytical and experimental performance of power tiller on the field may be summarized as follows; (1) The mathematical equation of rolIing resistance was derived as $$Rh=\frac {W_z-AC \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\] sin\theta_1}} {tan\phi \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]+\frac{tan\theta_1}{1}$$ and angle of rolling resistance as $$\theta _1 - tan^1\[ \frac {2T(AcrS_0 - T)+\sqrt (T-AcrS_0)^2(2T)^2-4(T^2-W_2^2r^2)\times (T-AcrS_0)^2 W_z^2r^2S_0^2tan^2\phi} {2(T^2-W_z^2r^2)S_0tan\phi}\] $$and the equation of frft force was derived as$$P=(AC+Rtan\phi)\[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]cos\phi_1 \ulcorner \frac {W_z \ulcorner{AC\[ [1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]sin\phi_1 {tan\phi[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\]+ \frac {tan\phi_1} { 1} \ulcorner W_1sin\alpha $$The slip coefficient K in these equations was fitted to approximately 1. 5 on the level lands and 2 on the slope land. (2) The coefficient of rolling resistance Rn was increased with increasing slip percent 5 and did not influenced by the angle of slope land. The angle of rolling resistance Ol was increasing sinkage Z of driving wheel. The value of Ol was found to be within the limits of Ol =2\ulcorner "'16\ulcorner. (3) The vertical weight transfered to power tiller on general slope land can be estim ated by use of th~ derived equation: $$R_pz= \frac {\sum_{i=1}^{4}{W_i}} {l_T} { (l_T-l) cos\alpha cos\beta \ulcorner \bar(h) sin \alpha - W_1 cos\alpha cos\beta$$The vertical transfer weight $R_pz$ was decreased with increasing the angle of slope land. The ratio of weight difference of right and left driving wheel on slop eland,$\lambda= \frac { {W_L_Z} - {W_R_Z}} {W_Z} $, was increased from ,$\lambda$=0 to$\lambda$=0.4 with increasing the angle of side slope land ($\beta = 0^\circ~20^\circ) (4) In case of no draft resistance, the difference between the travelling velocities on the level and the slope land was very small to give 0.5m/sec, in which the travelling velocity on the general slope land was decreased in curvilinear trend as the draft load increased. The decreasing rate of travelling velocity by the increase of side slope angle was less than that by the increase of hill slope angle a, (5) Rate of side slip by the side slope angle was defined as $ S_r=\frac {S_s}{l_s} \times$ 100( %), and the rate of side slip of the low travelling velocity was larger than that of the high travelling velocity. (6) Draft forces of power tiller did not affect by the angular velocity of driving wheel, and maximum draft coefficient occurred at slip percent of S=60% and the maximum draft power efficiency occurred at slip percent of S=30%. The maximum draft coefficient occurred at slip percent of S=60% on the side slope land, and the draft coefficent was nearly constant regardless of the side slope angle on the hill slope land. The maximum draft coefficient occurred at slip perecent of S=65% and it was decreased with increasing hill slope angle $\alpha$. The maximum draft power efficiency occurred at S=30 % on the general slope land. Therefore, it would be reasonable to have the draft operation at slip percent of S=30% on the general slope land. (7) The portions of the power supplied by the engine of the power tiller which were used as the source of draft power were 46.7% on the concrete road, 26.7% on the level land, and 13~20%; on the general slope land ($\alpha = O~ 15^\circ ,\beta = 0 ~ 10^\circ$) , respectively. Therefore, it may be desirable to develope the new mechanism of the external pO'wer transmitting system for the general slope land to improved its performance.l slope land to improved its performance.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.34-34
• /
• 1978

To find out the power tiller's travel and tractive characteristics on the general slope land, the tractive p:nver transmitting system was divided into the internal an,~ external power transmission systems. The performance of power tiller's engine which is the initial unit of internal transmission system was tested. In addition, the mathematical model for the tractive force of driving wheel which is the initial unit of external transmission system, was derived by energy and force balance. An analytical solution of performed for tractive forces was determined by use of the model through the digital computer programme. To justify the reliability of the theoretical value, the draft force was measured by the strain gauge system on the general slope land and compared with theoretical values. The results of the analytical and experimental performance of power tiller on the field may be summarized as follows; (1) The mathematical equation of rolIing resistance was derived as $$Rh=\frac {W_z-AC \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\] sin\theta_1}} {tan\phi \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]+\frac{tan\theta_1}{1}$$ and angle of rolling resistance as $$\theta _1 - tan^1\[ \frac {2T(AcrS_0 - T)+\sqrt (T-AcrS_0)^2(2T)^2-4(T^2-W_2^2r^2)\times (T-AcrS_0)^2 W_z^2r^2S_0^2tan^2\phi} {2(T^2-W_z^2r^2)S_0tan\phi}\] $$and the equation of frft force was derived as$$P=(AC+Rtan\phi)\[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]cos\phi_1 ? \frac {W_z ?{AC\[ [1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]sin\phi_1 {tan\phi[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\]+ \frac {tan\phi_1} { 1} ? W_1sin\alpha $$The slip coefficient K in these equations was fitted to approximately 1. 5 on the level lands and 2 on the slope land. (2) The coefficient of rolling resistance Rn was increased with increasing slip percent 5 and did not influenced by the angle of slope land. The angle of rolling resistance Ol was increasing sinkage Z of driving wheel. The value of Ol was found to be within the limits of Ol =2? "'16?. (3) The vertical weight transfered to power tiller on general slope land can be estim ated by use of th~ derived equation: $$R_pz= \frac {\sum_{i=1}^{4}{W_i}} {l_T} { (l_T-l) cos\alpha cos\beta ? \bar(h) sin \alpha - W_1 cos\alpha cos\beta$$The vertical transfer weight $R_pz$ was decreased with increasing the angle of slope land. The ratio of weight difference of right and left driving wheel on slop eland,$\lambda= \frac { {W_L_Z} - {W_R_Z}} {W_Z} $, was increased from ,$\lambda$=0 to$\lambda$=0.4 with increasing the angle of side slope land ($\beta = 0^\circ~20^\circ) (4) In case of no draft resistance, the difference between the travelling velocities on the level and the slope land was very small to give 0.5m/sec, in which the travelling velocity on the general slope land was decreased in curvilinear trend as the draft load increased. The decreasing rate of travelling velocity by the increase of side slope angle was less than that by the increase of hill slope angle a, (5) Rate of side slip by the side slope angle was defined as $ S_r=\frac {S_s}{l_s} \times$ 100( %), and the rate of side slip of the low travelling velocity was larger than that of the high travelling velocity. (6) Draft forces of power tiller did not affect by the angular velocity of driving wheel, and maximum draft coefficient occurred at slip percent of S=60% and the maximum draft power efficiency occurred at slip percent of S=30%. The maximum draft coefficient occurred at slip percent of S=60% on the side slope land, and the draft coefficent was nearly constant regardless of the side slope angle on the hill slope land. The maximum draft coefficient occurred at slip perecent of S=65% and it was decreased with increasing hill slope angle $\alpha$. The maximum draft power efficiency occurred at S=30 % on the general slope land. Therefore, it would be reasonable to have the draft operation at slip percent of S=30% on the general slope land. (7) The portions of the power supplied by the engine of the power tiller which were used as the source of draft power were 46.7% on the concrete road, 26.7% on the level land, and 13~20%; on the general slope land ($\alpha = O~ 15^\circ ,\beta = 0 ~ 10^\circ$) , respectively. Therefore, it may be desirable to develope the new mechanism of the external pO'wer transmitting system for the general slope land to improved its performance.

• Journal of Food Hygiene and Safety
• /
• v.28 no.4
• /
• pp.349-353
• /
• 2013

This study was performed to evaluate the bactericidal efficacy of Fumagari OPP$^{(R)}$, fumigation disinfectant, containing 20% ortho-phenylphenol against Staphylococcus aureus (S. aureus). In this research, efficacy test of fumigant against S. aureus was carried out according to French standard NF T 72-281. S. aureus working culture suspension number (N value), all of the colony numbers on the carriers exposed with the fumigant (n1, n2, and n3), the number of bacterial test suspentions by pour plate method (N1), the number of bacterial test suspentions by filter membrane method (N2) and the mean number of bacteria recovered on the control-carriers (T value) were obtained from the preliminary test. In addition, the reduction number of S. aureus exposed with the fumigant (d value) was calculated using T value, the mean number of bacteria in recovery solution (n'1) and the mean number of bacteria on carriers plated in agar (n'2). N value was $4.0{\times}10^8$ CFU/mL, and n1, n2, and n3 were higher than 0.5N1, 0.5N2 and 0.5N1, respectively. Additionally, T value was $3.4{\times}10^6$ CFU/mL. In the bactericidal effect of the fumigant, the d value was 6.43 logCFU/mL. According to the French standard for the fumigant, the d value for the effective bactericidal fumigant should be over than 5 logCFU/mL. The results indicated that Fumagari OPP$^{(R)}$ had an effective bactericidal activity against S. aureus, then the fumigant can be applied to disinfect food materials and kitchen appliances contaminated with pathogenic bacteria.

• Journal of Biomedical Engineering Research
• /
• v.25 no.5
• /
• pp.391-401
• /
• 2004

3D imaging systems using 2D phased arrays have a large number of active channels, compelling to use a very expensive and bulky beamforming hardware, and suffer from low volume rate because, in principle, at least one ultrasound transmit-receive event is necessary to construct each scanline. A high speed 3D imaging method using a cross array proposed previously to solve the above limitations can implement fast scanning and dynamic focusing in the lateral direction but suffer from low resolution except at the fixed transmit focusing along the elevational direction. To overcome these limitations, we propose a new real-time volumetric imaging method using a cross array based on the synthetic aperture technique. In the proposed method, ultrasound wave is transmitted successively using each elements of an 1D transmit array transducer, one at a time, which is placed along the elevational direction and for each firing, the returning pulse echoes are received using all elements of an 1D receive array transducer placed along the lateral direction. On receive, by employing the conventional dynamic focusing and synthetic aperture method along lateral and elevational directions, respectively, ultrasound waves can be focused effectively at all imaging points. In addition, in the proposed method, a volume of interest consisting of any required number of slice images, can be constructed with the same number of transmit-receive steps as the total number of transmit array elements. Computer simulation results show that the proposed method can provide the same and greatly improved resolutions in the lateral and elevational directions, respectively, compared with the 3D imaging method using a cross array based on the conventional fixed focusing. In the accompanying paper, we will also propose a new real-time 3D imaging method using a cross array for improving transmit power and elevational spatial resolution, which uses linear wave fronts on transmit.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.31 no.2
• /
• pp.257-262
• /
• 2002

Effects of dietary fatty acids and vitamin E on antioxidant system were studied in rat liver and serum. Sources of dietary fat (10 wt%) were safflower oil (SO) poor in $\omega$3 fatty acid and mixed oil (MO) with computer-adjusted fatty acid ratios (AA/DHA=1.4, $\omega$6/$\omega$3=6.3, P/M/S=1.0/l.5/1) with (ME) and without (MO) vitamin E (500 mg/kg diet). Rats were fed the three kinds of diet from 3~4 wks prior to the conception. At the age of 3 and 9 wks of the second generation rat, antioxidant vitamins and glutathione peroxidase (GSH-Px), superoxide dismutase (SOD) activities were measured in the liver and serum. The concentrations of $\beta$-carotene were lower in ME than in MO and SO in the liver at the age of 3 wks. It seemed that vitamin E has an inhibitory action on the uptake of $\beta$-carotene or acts as a preferred antioxidant to $\beta$-carotene. The concentrations of lycopene were lower in SO than in MO in the liver at the age of 3 wks. The concentrations of cryptoxanthin showed no significant changes within groups. The activities of GSH-Px tended to increase in ME compared to MO and the ratios of SOD/GSH-Px tended to decrease in ME compared to MO in the liver at the age of 3 weeks. The activities of antioxidant enzyme at the age of 3 weeks and 9 weeks were similar. This suggested that the activity level of antioxidant enzymes reached to the adult level at the age of 3 weeks which is the end point of lactation period.

• Journal of Agricultural Extension & Community Development
• /
• v.21 no.1
• /
• pp.35-82
• /
• 2014

It was main objectives to find the learners characteristics and educational effects of cyber agricultural technology courses in RDA. For the research, it was followed by literature reviews and internet based survey methods. In internet based survey, two staged stratified sampling method was adopted from cyber training members database in RDA along with some key word as open course or certificate course, and enrollment years. Instrument was composed through literature reviews about cyber education effects and educational effect factors. And learner characteristics items were added in survey documents. It was sent to sampled persons by e-mail and 316 data was returned via google survey systems. Through the data cleaning, 303 data were analysed by chi-square, t-test and F-test. It's significance level was .05. The results of the research were as followed; First, the respondent was composed of mainly man(77.9%), and monthly income group was mainly 2,000,000 or 3,000,000 won(24%), bachelor degree(48%), fifty or forty age group was shared to 75%, and their job was changed after learning(12.2%). So major respondents' job was not changed. Their major was not mainly agriculture. Learners' learning style were composed of two or more types as concrete-sequential, mixing, abstract-random, so e-learning course should be developed for the students' type. Second, it was attended at 3.2 days a week, 53.53 minutes a class, totally 172.63 minutes a week. They were very eager or generally eager to study, and attended two or more subjects. The cyber education motives was for farming knowledge, personal competency development, job performance enlarging. They selected subjects along with their interest. A subject person couldn't choose more subjects for little time, others, non interesting subject, but more subject persons were for job performance benefits and previous subjects effectiveness. Most learner was finished their subject, but a fourth was not finished for busy (26.7%). And their entrying behavior was not enough to learn e-course and computer or internet using ability was middle level as software using. And they thought RDA cyber course was comfort in non time or space limit, knowledge acquisition, and personal competency development. Cyber learning group was composed of open course only (12.5%), certificate only(25.7%), both(36.3%). Third, satisfaction and academic achievement of e-learning learners were good, and educational service offering for doing job in learning application category was good, but effect of cyber education was not good, especially, agricultural income increasing was not good because major learner group was not farmer, so they couldn't apply their knowledge to farming. And content structure and design, content comprehension, content amount were good. The more learning subject group responded to good in effects, and both open course and certificate course group satisfied more than open course only group. Based on the results, recommendation was offered as cyber course specialization before main course in RDA training system, support staff and faculty enlargement, building blended learning system with local RDA office, introducing cyber tutor system.

• Journal of Intelligence and Information Systems
• /
• v.20 no.2
• /
• pp.123-136
• /
• 2014

Recently, online shopping has further developed as the use of the Internet and a variety of smart mobile devices becomes more prevalent. The increase in the scale of such shopping has led to the creation of many Internet shopping malls. Consequently, there is a tendency for increasingly fierce competition among online retailers, and as a result, many Internet shopping malls are making significant attempts to attract online users to their sites. One such attempt is keyword marketing, whereby a retail site pays a fee to expose its link to potential customers when they insert a specific keyword on an Internet portal site. The price related to each keyword is generally estimated by the keyword's frequency of appearance. However, it is widely accepted that the price of keywords cannot be based solely on their frequency because many keywords may appear frequently but have little relationship to shopping. This implies that it is unreasonable for an online shopping mall to spend a great deal on some keywords simply because people frequently use them. Therefore, from the perspective of shopping malls, a specialized process is required to extract meaningful keywords. Further, the demand for automating this extraction process is increasing because of the drive to improve online sales performance. In this study, we propose a methodology that can automatically extract only shopping-related keywords from the entire set of search keywords used on portal sites. We define a shopping-related keyword as a keyword that is used directly before shopping behaviors. In other words, only search keywords that direct the search results page to shopping-related pages are extracted from among the entire set of search keywords. A comparison is then made between the extracted keywords' rankings and the rankings of the entire set of search keywords. Two types of data are used in our study's experiment: web browsing history from July 1, 2012 to June 30, 2013, and site information. The experimental dataset was from a web site ranking site, and the biggest portal site in Korea. The original sample dataset contains 150 million transaction logs. First, portal sites are selected, and search keywords in those sites are extracted. Search keywords can be easily extracted by simple parsing. The extracted keywords are ranked according to their frequency. The experiment uses approximately 3.9 million search results from Korea's largest search portal site. As a result, a total of 344,822 search keywords were extracted. Next, by using web browsing history and site information, the shopping-related keywords were taken from the entire set of search keywords. As a result, we obtained 4,709 shopping-related keywords. For performance evaluation, we compared the hit ratios of all the search keywords with the shopping-related keywords. To achieve this, we extracted 80,298 search keywords from several Internet shopping malls and then chose the top 1,000 keywords as a set of true shopping keywords. We measured precision, recall, and F-scores of the entire amount of keywords and the shopping-related keywords. The F-Score was formulated by calculating the harmonic mean of precision and recall. The precision, recall, and F-score of shopping-related keywords derived by the proposed methodology were revealed to be higher than those of the entire number of keywords. This study proposes a scheme that is able to obtain shopping-related keywords in a relatively simple manner. We could easily extract shopping-related keywords simply by examining transactions whose next visit is a shopping mall. The resultant shopping-related keyword set is expected to be a useful asset for many shopping malls that participate in keyword marketing. Moreover, the proposed methodology can be easily applied to the construction of special area-related keywords as well as shopping-related ones.