• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.777-784
• /
• 1997

This paper is fundamental study to develop ceiling materials, using the properties of Zeolite, stone dust and sludge for the purpose of prevention of environmental pollution and reuse of industrial wastes. According to latin square method, We estimated to the significant level ad optimum level for a significant factor, and investigated to the significant degree to extend each factor for required capacity. Thus, we investigated for required capacity in ceiling material such as, compressive and bending strength, absorptivity and thermal conductivity.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.463-468
• /
• 1998

This paper presents the shear behavior in reinforced normal and high-strength concrete beams with Belite cement due to the increase of concrete compressive strength. The shear tests were conducted on thirty two beam specimens having concrete compressive strengths of 350 and 600kg/$\textrm{cm}^2$. The major experimental variables are compressive strength of concrete, shear span to depth ratio, and shear reinforcement ratio. The shear responses as to each variable are discussed in terms of shear capacity. The comparison of prediction equations with test results is also presented.

• KCI Concrete Journal
• /
• v.14 no.4
• /
• pp.139-144
• /
• 2002

Concrete filled FRP tube has lately attracted attention as the member that can substitute the conventional reinforced concrete. Glass fiber and carbon fiber are some of available materials for FRP tube. Carbon tube is filament wound with specified winding angle to meet the appropriate capacity demands. Confinement effect of carbon tube is varied according to winding angle. In this study, a total 4 of large scale circular specimens of 30cm diameter and 60cm height is tested. To estimate the effect of winding angle and thickness of carbon tube on the increased confined compressive strength, the test tube are wound with $\pm45^{\circ}\;and\;\pm30^{\circ}$ with two types of thickness, 2mm and 3mm, respectively. It is shown that effectively increased confined strength and ductility are observed from the specimens with $\pm45^{\circ}$ winding angle than $\pm30^{\circ}$ winding angle. Increasing thickness is not as effective as adjusting winding angle for the confinement of concrete core.

• Computers and Concrete
• /
• v.22 no.1
• /
• pp.11-25
• /
• 2018

A numerical approach for the evaluation of the flexural response of Steel Fibrous Concrete (SFC) cross-sections with arbitrary geometry, with or without conventional steel longitudinal reinforcing bars is proposed. Resisting bending moment versus curvature curves are calculated using verified non-linear constitutive stress-strain relationships for the SFC under compression and tension which include post-peak and post-cracking softening parts. A new compressive stress-strain model for SFC is employed that has been derived from test data of 125 stress-strain curves and 257 strength values providing the overall compressive behaviour of various SFC mixtures. The proposed sectional analysis is verified using existing experimental data of 42 SFC beams, and it predicts the flexural capacity and the curvature ductility of SFC members reasonably well. The developed approach also provides rational and more accurate compressive and tensile stress-strain curves along with bending moment versus curvature curves with regards to the predictions of relevant existing models.

• Computers and Concrete
• /
• v.25 no.3
• /
• pp.267-272
• /
• 2020

This paper investigates the effect of crumb rubber (CR) on compressive behaviour of crumb rubber concrete filled steel tube (CRCFST) stub columns. Therefore, experiments on 16 stub columns subjected to axial loading are carried out. The results show that the failure modes of CRCFST stub columns with different CR replacement ratios and CR size are similar, manifested the buckling of the outer steel tube. The axial bearing capacity and stiffness both decrease with an increase in CR replacement ratio, and with decreasing CR size.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.442-445
• /
• 1997

With increasing use of high strength concrete tied columns in structural engineering, it becomes necessary to examine the applicability of related sections of current design codes. High strength concrete has an advantage of strength capacity and stiffness especially for column elements. This paper presents an experimental study of high strength concrete tied columns subjected to eccentric loading. The main variables included in this test were concrete compressive strength, steel amount, eccentricity, and slenderness ratio. The concrete compressive strength varied from 34.9Mpa(356kg/$\textrm{cm}^2$ ) to 93.2Mpa(951kg/$\textrm{cm}^2$ ) and the longitudinal steel ratios were between 1.1% and 5.5%. The eccentricity was selected for the different failure modes, i.e., compression control, balanced point, and tension control. The slenderness ratio varied from 19 to 61. The column specimens with same slenderness ratio but with different concrete compressive strength were constructed and tested. The purpose of this paper is to show failure modes of high strength reinforced concrete columns.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.1
• /
• pp.161-168
• /
• 2001

The use of composite members to improve the compressive strength of steel structure is a common practice these days and its efficiency has already been proved by several researches and experiments. The result of concrete filled circular tubular(CFCT) stub column tests is introduced in this paper. The main parameter of this test is the ratio of diameter to thickness of circular hollow section. From the test results, the effect of concrete filled in steel tube on the ultimate strength, the deformation capacity and initial stiffness are discussed. The purpose of this paper is to investigate the effect of various parameters and evaluate the compressive strength of confined concrete. It would contribute to a better understanding of CFT structure, further laboratory experimentations are needed for better accurate estimation on its effect.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1139-1144
• /
• 2000

Recent advance in material technology has accelerated the development of high strength concrete using lightweight artificial aggregates. The lightweight concrete has many advantages that the reduction of dead lads and the increase in load capacity can ofter. In this study, lightweight polymer concrete using unsaturated polyester resin and lightweight aggregate were prepared and tested for testing the physical and the mechanical properties. The compressive strengths of lightweight polymer concretes with specific gravities from 1.32 to 1.78 were compressive strength of 250 to 470 $kgf/cm^2$ and flexural strengths were measured to be in the range of a third to a quarter of compressive strength

• Journal of Korean Association for Spatial Structures
• /
• v.17 no.1
• /
• pp.59-67
• /
• 2017

In this study, load transfer tests based on KCI-PS101 were conducted to verify the performance of spiral anchorage zone reinforcement for banded post-tensioning (PT) monostrands. With results, the compressive strength of spiral reinforcement was increased by about 20% than that of specimens with two horizontal steel bars and 8% than that of U-shaped bars. Advanced spiral reinforcement for corner increases compressive strength and can resist the spalling forces or fall-out effect at the corner by shear. The ratio of maximum load to amount of steel of the spiral reinforcement is about twice than that of U-shaped reinforcement. With increase of compressive strength capacity and improvement of constructability, the spiral reinforcement is considered to have advantages of promoting the performance of PT anchorage zone compared to conventional methods.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.12 s.255
• /
• pp.1603-1610
• /
• 2006

In this paper compressive characteristics of composite egg-box panels were investigated and energy absorption was calculated from the nominal stress-strain relations obtained by the compressive tests. Several different stacking sequences and number of plies were introduced for investigation of static compression characteristics and the energy absorption rates of composite egg-box panels. The compressive stress-strain relation and energy absorption of various composite egg-box panels were compared with those of aluminium egg-box panels. From the test results it was found that the fracture behavior of composite egg-box panel was affected by stacking angle causing different local deformation, during lay-up and draping processes and types of prepreg; that is, plain weave carbon/epoxy and 4-harness satin glass/epoxy. The energy absorption capacity of composite egg-box panels were proved to be higher than that of aluminium egg-box panels with low mass.