• Journal of the Korean Geotechnical Society
• /
• v.16 no.2
• /
• pp.79-89
• /
• 2000

The application of stabilization method has increased because of short construction periods, no environmental problems with dumped and replaced soil, assurance of required strength and economical effect with mid to small size construction. The unconfined and triaxial(UU-condition) compression tests were executed with each mixing sample for the study of the improvement effects and the effect of design-parameters by the stabilization methods. Three typical stabilizers, which are representative in Korea, were applied in this study, and three common soils(very soft clay, general weathered soil, common clay), which are common in Korea, were used in this study. In this study, the effect of engineering factors(soils, stabilizers and water contents, etc.) which are important parameters for the improvement effects of mixed ground by stabilizers, was analyzed. As results, the tendencies of design-parameters(unconfined compression strength, deformation modulus and strength parameter) are presented and the criteria of the application of stabilization methods are suggested.

• Korean Journal of Materials Research
• /
• v.27 no.1
• /
• pp.19-24
• /
• 2017

This paper is concerned with a test method that can be used to investigate the parameters of the Johnson-Cook constitutive model. These parameters are essential for accurately analyzing material behavior under impact loading conditions in numerical simulation. Ti-6Al-4V alloy (HCP crytal structure) was used as a specimen for the experiments. In the $10^{-3}-10^3/s$ strain rate range, three types of experimental methods (convention, compression and tension) were employed to compare the differences using MTS-810, SHPB and SHTB. Finite element analysis results when applying these parameters were displayed along with the experiment results.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.701-709
• /
• 2002

Aluminium foam material is highly porous material, which has the complicated cellular structure defined by randomly distributed pores in metallic matrix. This structure gives the characteristic properties which cannot be achieved by any other conventional processes. As the properties of aluminium foam material significantly depend on its porosity, a desired profile of properties can be tailored by changing the foam density. But various defects lead to undesirable effects on the mechanical properties. Mechanical properties are dependent on cell sizes and aspect ratios. Therefore, this paper presents the effects of various processing parameters of various parameters on the mechanical properties. For the sake of this, combined stirring was used to fabricate aluminum foam materials by the parameters. Compression and bending tests were performed to investigate the effects of cell sizes and aspect ratios on the mechanical properties.

• Journal of ILASS-Korea
• /
• v.9 no.4
• /
• pp.9-16
• /
• 2004

A study of the propeny and performance effect of Indolene - Methanol Plus High Alcolhols (MPHA) has been completed. This study invested the measurement of fuel properties and performance parameters. The fuel properties investigated are distillation characteristics, heating valuer flash point, specific gravity and water tolerance. The performance parameters measured are minimum advance for best torque (MBT) spark timing, power output. The alcohol concentration was varied from 0 to 100 percent by volume in clear Indolene. The measurement of fuel properties indicated that, in general, Indolene - MPHA blends have higher water tolerance, similar specific gravity, similar flash point and different distillation characteristics compared to Indolene - Methanol blends. The performance parameters were measured using a single cylinder spark ignition engine at different compression ratios. The results of the performance measurements indicated that Indolene - MPHA blends have a higher MBT spark advance, similar power output.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.4
• /
• pp.520-527
• /
• 2017

In this study, the experimental methods are compared for obtaining the parameters of the Johnson-Cook constitutive model. The parameters used for numerical simulation are very important in making an accurate estimation of numerical simulation. So, the testing method of obtaining the parameters is also very important. We compared the difference of conventional method, compression method and tensile method of AISI-4340 steel at various strain rate by using MTS, SHPB and SHTB. Taylor impact test and M&S were carried out to compare differences among these three types of JC constitutive parameter.

• Steel and Composite Structures
• /
• v.38 no.1
• /
• pp.103-120
• /
• 2021

This research examines the eccentric compression performance of composite columns composed of recycled aggregate concrete (RAC)-filled square steel tube and profile steel. A total of 17 specimens on the composite columns with different recycled coarse aggregate (RCA) replacement percentage, RAC strength, width to thickness ratio of square steel tube, profile steel ratio, eccentricity and slenderness ratio were subjected to eccentric compression tests. The failure process and characteristic of specimens under eccentric compression loading were observed in detail. The load-lateral deflection curves, load-train curves and strain distribution on the cross section of the composite columns were also obtained and described on the basis of test data. Results corroborate that the failure characteristics and modes of the specimens with different design parameters were basically similar under eccentric compression loads. The compression side of square steel tube yields first, followed by the compression side of profile steel. Finally, the RAC in the columns was crushed and the apparent local bulging of square steel tube was also observed, which meant that the composite column was damaged and failed. The composite columns under eccentric compression loading suffered from typical bending failure. Moreover, the eccentric bearing capacity and deformation of the specimens decreased as the RCA replacement percentage and width to thickness ratio of square steel tube increased, respectively. Slenderness ratio and eccentricity had a significantly adverse effect on the eccentric compression performance of composite columns. But overall, the composite columns generally had high-bearing capacity and good deformation. Meanwhile, the mechanism of the composite columns under eccentric compression loads was also analysed in detail, and the calculation formulas on the eccentric compression capacity of composite columns were proposed via the limit equilibrium analysis method. The calculation results of the eccentric compression capacity of columns are consistent with the test results, which verify the validity of the formulas, and the conclusions can serve as references for the engineering application of this kind of composite columns.

• Steel and Composite Structures
• /
• v.22 no.6
• /
• pp.1417-1443
• /
• 2016

Cellular and castellated steel beams are used to obtain higher stiffness and bending capacity using the same weight of steel. In addition, the beam openings may be used as a pass for different mechanical fixtures such as ducts and pipes. The aim of this study is to investigate the effect of different parameters on both elastic and inelastic critical buckling stresses of steel web plates with openings. These parameters are plate aspect ratio; opening shape (circular or rectangular); end distance to the first opening; opening spacing; opening size; plate slenderness ratio; steel grade; and initial web imperfection. The web/flange interaction has been simplified by web edge restraints representing simply supported boundary conditions. A numerical parametric study has been performed through linear and nonlinear finite element (FE) models, where the FE results have been verified against both experimental and numerical results in the literature. The web plates are subject to in-plane linearly varying compression with different loading patterns, ranging from uniform compression to pure bending. A buckling stress modification factor (${\beta}$-factor) has been introduced as a ratio of buckling stress of web plate with openings to buckling stress of the corresponding solid web plate. The variation of ${\beta}$-factor against the aforementioned parameters has been reported. Furthermore, the critical plate slenderness ratio separating elastic buckling and yielding has been identified and discussed for two steel grades of DIN-17100, namely: ST-37/2 and ST-52/3. The FE results revealed that the minimum ${\beta}$-factor is 0.9 for web plates under uniform compression and 0.7 for those under both compression and tension.

• Fibers and Polymers
• /
• v.7 no.3
• /
• pp.295-304
• /
• 2006

High-bulk worsted yams with different shrinkable and non-shrinkable acrylic fibers blend ratios are produced and then single jersey weft knitted fabrics with three different structures and loop lengths are constructed. The physical properties of produced yams and compression properties of produced fabrics at eight pressure values (50, 100, 200, 500, 1000, 1500 and $2000 g/cm^2$) were measured using a conventional fabric thickness tester. Then, weft-knitted fabric compression behavior was analyzed using a two parameters model. It is found that at 40 % shrinkable fibre blending ratio the maximum yam bulk, shrinkage, abrasion resistance and minimum yarn strength are obtained. It is also shown that high-bulk acrylic yarn has the highest elongation at 20 % shrinkable fibre blend ratio. The statistical regression analysis revealed that the compression behavior of acrylic weft-knitted fabrics is highly closed to two parameter model proposed for woven fabrics. It is also shown that for weft-knitted structure, there is an incompressible layer (V') which resists against high compression load. Acrylic weft-knitted fabrics with knit-tuck structure exhibit higher compression rigidity and lower softness than the plain and knit-miss structures. In addition, at 20 % shrinkable fibre blend ratio, the high-bulk acrylic weft-knitted fabrics are highly compressible.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.38 no.4
• /
• pp.440-454
• /
• 2014

This study examined the wearing effect of 3D compression suits on quantitative electroencephalogram (EEG) during walking and rest. Ten males in their 20s wore three types of experimental clothing, a loose-fit wear (BS), a 3D compression suit (3D CS), and a power film welded on CS (3D WCS); in addition, EEG signals were measured during resting, walking, after walking, and after sit-ups. The results showed that a higher pressure (due to 3D CS and 3D WCS) increased the 'Concentration' level and the 'Cognitive load' of brain waves during treadmill walking due to a higher cortex activity level when walking. Differentiation was shown between two compression suits and BS was enhanced during walking on a treadmill; however, the brain waves of 'Relaxation' between two compression suits were significantly different after walking, i.e., 'Relaxation' level of 3D WCS was the highest. Rigorous exercise such as sit-ups was inefficient to distinguish the effect of compression suits on EEG. Participants perceived a higher pressure due to compression suits; however, the wear comfort of two compression suits was maintained. Two compression suits were rated as supportive and helpful during walking. Various EEG parameters such as the indices of 'Relaxation', 'Concentration' and 'Cognitive load' were effective to observe the effect of 3D compression suits on wearers' brain waves during and after walking.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.4
• /
• pp.97-104
• /
• 2015

When carrying out design for soft ground improvement before reclamation of dredged soil, it is very important to appropriately evaluate design parameters such as compression index and undrained strength in order to estimate optimum construction cost. In this study, consolidation and strength parameters were estimated by the samples obtained from the similar reclaimed land. Water content and compression index of dredged soil reclaimed by hydraulic fill method were quite decreased in comparison with those of in-situ conditions at Incheon site. Relationships between compression index(Cc) and water content (wn), and between undrained strength (su) and water content (wn) for dredged soil were obtained by field vane test and oedometer test, respectively. Applicability of Schmertmann correction method (compression index) for low plasticity silty soil was discussed according to comparison with designed and measured settlements.