• Proceedings of the IEEK Conference
• /
• 2000.09a
• /
• pp.281-285
• /
• 2000

This paper proposes context-based coding methods for variable length coding of inter-frame DCT coefficients. The proposed methods classify run-level symbols depending on the preceding coefficients. No extra overhead needs to be transmitted, since the information of the previously transmitted coefficients is used for classification. Two entropy coding methods, arithmetic coding and Huffman coding, are used for the proposed context-based coding. For Huffman coding, there is no complexity increase from the current standards by using the existing inter/intra VLC tables. Experimental results show that the proposed methods give ～ 19% bits gain and ～ 0.8 dB PSNR improvement for adaptive inter/intra VLC table selection, and ～ 37% bits gain and ～ 2.7dB PSNR improvement for arithmetic coding over the current standards, MPEG-4 and H.263. Also, the proposed methods obtain larger gain for small quantizaton parameters and the sequences with fast and complex motion. Therefore, for high quality video coding, the proposed methods have more advantage.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.303-311
• /
• 2001

The pumping speed and the maximum compression ratio as well as the critical backing pressure as main parameters representing normal and limiting performance of a turbomolecular pump and a compound molecular pump were measured basing on a draft KS of the acceptance test procedure. Characteristics of the molecular pumps of two different kinds were compared and some points for improving regulations of the test procedure were proposed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.04a
• /
• pp.107-112
• /
• 1993

The objective of this experimental investigation is to examine the feasibility and the usefulness of the complementary crosstie in the current ACI 318-89 code for rienforced concrete columns subjected to constant axial load and lateral load reversals. Tests were conducted on1/3 scaled four columns with the length of 1.9m and the cross section of 20$\times$20 cm. The main parameters of specimens were the magnitude of axial load applied and the configuration of transverse reinforcements . From the experimental results, it can be seen that while the column subjected to lower axial load represented considerable ductility behaviors, the column subjected to higher axial load showed the brittle failure

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.529-532
• /
• 1999

With increasing use of high-strength concrete tied columns in structural engineering, it becomes necessary to examine the applicability of related sections of the current design codes. This experimental study was conducted to investigate the behavior of eccentrically loaded high-strength concrete columns. Column specimens with concrete strength 234, 437, 703kgf/㎠ were tested under monotonically increasing eccentric compression. The test parameters included the longitudinal reinforcement ratio, eccentric distance and concrete compressive strength. The analytical results obtained from the stress-strain relationship and the ACI's equivalent rectangular stress block are compared with experimental test results.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.15-19
• /
• 2000

Recently Western countries are now beginning to use ACM (Advanced Composites Material), in the construction industry Compared with existing construction materials, ACM possesses many advantages such as light-weight, high-strength, corrosion resistant property. Among other fabrication process of ACM, pultrusion is one of the promising one for civil infrastructure application. In this paper, the structural characteristics of pultruded GFRP strip and structural members of angle and tube type were studied. For the strip, parametric studies of pultrusion process has been carried out. Considered parameters were volume fraction, temperature, pulling speed and fiber orientations. For the pultruded angle and tube, compression test and buckling analysis has been carried out. The results were compared with calculated values using coded formulae

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.365-370
• /
• 2001

The repairing technique of surface wrapping concrete structural members using fiber composite sheet have been widely used. The research efforts have been limited to studying relative strength increase of repaired concrete structures rather than ductility improvement based on composite material effect and the interface effect between composite and concrete. The compression tests of CFS(carbon fiber sheet) reinforced concrete specimens with various cross-sectional shapes and laminate angles have been peformed. FEM algorithm considering various parameters will be performed based on the obtained data. The results will be discussed in detail.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.444-450
• /
• 1998

In the present investigation, it is attempted to derive a yield function and associated flow rules of loose metal powders to predict plastic deformation and density change during compaction. The loose metal powders yield by shear stress as well as hydrostatic stress and the yield strength is much smaller in tension than compression. Therefore, a yield function for the powders is expressed as a shifted ellipse toward the negative direction in the hydrostatic stress axis in the space defined by the two stresses. Each of parameters A, B and .delta. used in the yield function is expressed as a function of relative density and it is determined by uniaxial strain and hydrostatic compressions using Cu powder. Flow rules obtained by imposing the normality rule to the yield function are applied to the analyses of unidirectional, bidirectional and hydrostatic compressions, resulting in an excellent agreement with experiments. The yield function is further examined by checking volume changes in plane stain, uniaxial strain and shear deformations.

• Journal of KSNVE
• /
• v.7 no.6
• /
• pp.909-918
• /
• 1997

Combustion oriented noise is a part of engine noise, which is mainly determined by the in-cylinder pressure profile and the structure attenuation of an engine. A numerical model for predicting the in-cylinder pressure profile and the resultant combustion noise developed by the use of a commercial code. The model is experimentally validated and updated based on the performance as well as the noise by considering the fuel injection timing, the fuel injection rate, Cetane number, intake temperature, and compression ratio. For providing a design guide of a fuel injector for a low combustion noise engine model, the optimal parameters of injection pressure profile, injection rate profile, and injection timing are determined, which gives the 5 dBA noise reduction.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.468-472
• /
• 2005

This paper is to investigate the influence of the endface quality on the loss characteristics of a plastic optical fiber connector for in-car network service. Using the parameters of the surface roughness and applied load, insertion loss of connector is measured. Due to scattering and change of refractive index, an optimal condition for low-loss coupling exists. We present the optimal condition as surface roughness $R_{rms}$ = 8 nm and contact load up to 50 N.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.375-380
• /
• 1993

We developed a part of stroke sensing cylinder and its measurement system for system for automatic excavator. In this paper, for development of stroke sensing sylinder, we consist of 2-axis control instrument system with magnetic sensor. A Performence of cylinder rod with magnetic scales is evaluated by its system. Furthmore, the position control for good performance of instrument system is achieved by a sliding mode control which is a new method diminishing the chattering in that control by setting 2-dead band along the swtching line. The unknown parameters for sliding mode control are estimated by the signal compression method.