• Journal of Korea Society of Waste Management
• /
• v.35 no.7
• /
• pp.571-586
• /
• 2018

The Malaysian biogas upgrading technologies and policies were examined. In Malaysia, the regulation of palm oil mill effluent (POME) has been enforced to reduce the biochemical oxygen demand to 20 ppm and the biogas capture in the palm oil mills have been recently enforced for renewable energy. A huge amount of organic waste is produced from POME, and 80 million tons from palm oil trees, every year. Due to the renewable energy trends, the Malaysian government is modifying the use of biogases as fuels in favor of their conversion into compressed natural gas (CNG) and other chemicals; various green policies are being promoted because of many advantages of the organic substances. The Korean policies for biogas are a good model for exporting environmental plants after upgrading the digestion and purification technologies. Therefore, this article introduces the current status of POME and biogas production in Malaysia, it could encourage creating a new market for biomethane.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.972-980
• /
• 2006

In general, to send out natural gas via a pipeline network across the nation in LNG terminal, high-pressure cryogenic pump supply highly compressed LNG to high-pressure vaporization facilities. The Number of cryogenic pumps determined the send-out amount in LNG receiving terminal. So it is main equipment at LNG production process and should be maintained on best conditions. In this paper, to find out the cause of high vibration at cryogenic pumps-motor system in LNG terminal, vibration spectrum analysis and motor current signature analysis have been performed together. Through the analysis, motor rotor bar problems are estimated by the vibration analysis and confirmed by the current analysis. So, it is demonstrated through the case study in this paper, how performing vibration analysis and current signature analysis together can reliable diagnosis rotor bar problems in pump-motor system.

• International Journal of Automotive Technology
• /
• v.4 no.1
• /
• pp.9-19
• /
• 2003

Exhaust emissions were characterized for a fleet of 10 alternative-fuel vehicles (AFVx) including 5 compressed natural gas (CNG) vehicles. 3 liquefied petroleum gas (LPG) vehicles and 2 85% methanol/15% California Phase 2 gasoline (M85) vehicles. In addition to the standard regulated emissions and detailed speciation of organic gas compounds, Fourier Transform Infrared Spectroscopy (FTIR) was used to measure ammonia (NH$_3$) and nitrous oxide ($N_2$O) emissions. NH$_3$, emissions averaged 0.124 g/mi for the vehicle fleet with a range from <0.004 to 0.540 g/mi. $N_2$O emissions averaged 0.022 g/mi over the vehicle fleet with range from <0.002 to 0.077 g/mi. Modal emissions showed that both NH$_3$, and $N_2$O emissions began during catalyst light-off and continued as the catalyst reached its operating temperature. $N_2$O emissions primarily were formed during the initial stages of catalyst light-off. Detailed speciation measurements showed that the principal component of the fuel was also the primary organic gas species found in the exhaust. In particular, methane, propane and methanol composed on average 93%, 79%, and 75% of the organic gas emissions, respectively, for the CNG, LPG. and M85 vehicles.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.3
• /
• pp.300-308
• /
• 2015

Recently supercavitating underwater torpedo moving at high speed (over 200 knots) has been interested for their practical advantage of the dramatic drag reduction. Cavitator located in front of the torpedo plays an important role to generate a natural supercavity and control the motion of the object. Supercavity can be created artificially by injection of compressed gas from the rear of the cavitator at a relatively low speed. In this paper, we investigated physical characteristics of artificial supercavities through cavitation tunnel experiments. One of the main focuses of the study was to measure pressure inside the cavity, and examined variation of the gravity effects appearing according to different amount of injected air. It was also found that a stable supercavity could be sustained at injection rates less than that required to form the stable supercavity because of hysteresis effect.

• Journal of the Korean Institute of Gas
• /
• v.16 no.6
• /
• pp.67-72
• /
• 2012

In this study, the leak-free performance and sealing endurance safety of CNG fueling nipple in which are related to the contact normal stress and equivalent true stress have been analyzed for CNG automobile using a finite element analysis. For the conventional circular o-rings and new double-lip o-rings with an initial compression rate of 15 percentages, the leak-free performance of double-lip o-rings with two contact sealing spots is 41% higher than that of the conventional circular o-rings with a contact sealing spot. The FEM computed results present that the leak-free endurance safety of double-lip o-rings with two contact sealing spots is 5% higher than that of the conventional circular o-rings for initial compression ratio of 15 percentages and a gas compression pressure of 8MPa. And, the maximum equivalent true stress of double-lip o-rings is 10.2% higher than that of the conventional circular o-rings for the leak-free endurance safety. This means that the double-lip o-ring may guarantee the extended sealing life compared to that of a conventional circular o-ring.

• Journal of the Korean Institute of Gas
• /
• v.15 no.2
• /
• pp.21-26
• /
• 2011

Emissoin of heavy duty vehicle have much positioned in air pollution although its limited number of vehicles. CNG vehicles are coming to the fore as one of the solution of diesel vehicles. CNG vehicles exhaust smaller emission than diesel vehicles on PM and NOx. In this study, aftertreatment technologies are introduced on vehicles which use CNG and hydrogenmixed fuel. Withmixing hydrogen with CNG, combustion efficiency is enhanced, and harmful emission might be decreased, but methane that is main component of CNG brings green house effect. In order to remove methane and NOx in exhaust gas of CNG engine, methane oxidation catalyst and SCR technologies were respectively analyzed.

• Journal of the Korean Institute of Gas
• /
• v.4 no.3 s.11
• /
• pp.53-58
• /
• 2000

It was carried out consequence analysis(CA) of CNG (compressed natural gas) service station and we compared the results of CA of CNG service station with LPG service station which was installed by high Pressure gas law. The results of CA were that distance of CNG LFL was 1.5 times than the length of LPG LFL. Thermal radiation effect about CNG may not be showed damage of process facilities, but in the case of LPG, it was enough to have an large damage effect on a downtown. The thermal radiation of 37.5 $kw/m^2$ extended 12.6 m. Also, in the case of 12.5 $kw/m^2$ which was able to burn wood, the radiation effect of LPG is 3 times than CNG.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.40-46
• /
• 2015

Stoichiometric combustion engine with Three-way catalyst had an advantage that can reduce the harmful emissions effectively. Fuel equivalence ratio controlled from engine is very important because Fuel equivalence ratio with high conversion efficiency was narrow. This study analyzed the conversion efficiency under whole range of operating area for to evaluate the performance of three-way catalyst. In order to identify the Optimum conversion efficiency, the conversion efficiency due to change the control value of fuel equivalence ratio was investigated. The result show that conversion efficiency of emissions(more than 95%) has discovered by means of fuel equivalence ratio control at each test condition. As engine power increases, optimal fuel equivalence ratio tended to increase linearly under operating conditions of similar exhaust gas temperature.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.10
• /
• pp.855-862
• /
• 2017

Due to the weight reduction and miniaturization of satellites, there is a growing interest in low-cost launch vehicles, which are cheaper to launch than larger launch vehicles. One of the most cost-effective ways to reduce the cost of launch vehicles is the reuse of vehicles. Most companies that are developing low cost launch vehicles are also adopting a vehicles reuse approach. Along with this reuse purpose, the demand for environmentally friendly space launch vehicles has increased, so the choice of fuel used for low cost launch vehicles has also become very important. Methane and hydrogen-enriched compressed natural gas (HCNG), which makes more energy-efficient by adding hydrogen to methane, are considered to be the most suitable when considering other factors such as energy density among the fuels that are eco-friendly and capable of reusing the launch vehicles. This study investigated the trends of low-cost launch vehicle and rocket fuel in the world as a reference for setting up domestic space development after the development of Korea Space Launch Vehicle-II.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.2
• /
• pp.427-435
• /
• 2017

Most of the domestic city buses are equipped with the pressure vessels subjected to internal pressure applied by compressed natural gas. Pressure vessels subjected to internal pressure are used in various forms and purposes. Fuel is explosive and has flammable high pressure. The damage of the pressure vessel causes many property damage and loss of life. Safe design for pressure vessel is always necessary. Due to these reasons, many studies using finite element analysis have been conducted. In this paper, the stresses of cylindrical vessel and spherical dome were analyzed using ANSYS, a finite element analysis software. In order to verify the validity of the analysis, a model with a perfectly spherical shape of the dome was designed and observed. Based on the ASME standard in used, stress distribution was also analyzed for models designed with compressed natural gas(CNG). The FEM analysis software agreed with the theory when the dome shape was perfectly spherical. The model designed based on the ASME specification theory, stress concentration occurred in the knuckle part.