• 연구논문집
• /
• 통권23호
• /
• pp.165-171
• /
• 1993

$Si_3N_4/Sic$. nano-composites were fabricated by hot-pressing, gas pressure sintering. The composites contained up to 50 wt. % of SiC. The mechanical properties such as strength, toughness, and hardness of the composite are compared each other. The flexural strength of the composites was improved significantly by introducing fine SiC particles into $Si_3N_4$ matrix, while the fracture toughness was not improved. The increase in flexural strength is attributed to the formation of uniformly elongated $\beta -Si_3N_4$ grains as well as the reduction of grain size.

• 대한기계학회논문집
• /
• 제19권7호
• /
• pp.1619-1629
• /
• 1995

The Al/Al$_{2}$O$_{3}$ SiC and Al/Al$_{2}$O$_{3}$/C hybrid metal matrix composites (MMCs) were fabricated by squeeze infiltration method. Uniform distribution of reinforcements were found in the microstructure of metal matrix composites. Mechanical tests were carried out under various test conditions to clearly identify mechanical behavior of MMCs, and the wear mechanism of Al/Al$_{2}$O$_{3}$/(SiC or C) hybrid metal matrix composites were investigated. The tensile strength and hardness of hybrid composites was resulted in increasing compared with those of the unreinforced matrix alloy. Wear resistance was strongly dependent upon kinds of fiber, volume fraction and sliding speed. The wear resistance of metal matrix composites was remarkably improved by the addition of reinforcements. Especially, the wear resistance of the hybrid composites of carbon fibers was more effective than in the composites reinforced with alumina and SiC whiskers of reinforcements. This was due to the effect of carbon fiber on the solid lubrication. Wear mechanisms of hybrid composites were suggested from wear surface analyses. The major wear mechanism of hybrid composites was the abrasive wear at low to intermediate sliding speed, and the melting wear at intermediate to high sliding speed.

• 농업과학연구
• /
• 제37권3호
• /
• pp.457-464
• /
• 2010

The low melting alloy impregnated wood composites with natural grain of thinned Juglans mandshurica was made and evaluated in this study. And the proper manufacturing conditions was also investigated in this study. The low melting alloy with bismuth(Bi) and tin(Sn) which are harmless to humans, was applied for this novel composites, which showed not only no defects of discoloration, delamination, swelling, and cracking, because of high dimensional stability and low thickness swelling, but also much improved performance such as high bending strength, high hardness, low abrasion, high thermal conductivity as floor materials. This study also suggested the proper impregnating condition, such as 10 minutes of the preliminary vacuum time, $187^{\circ}C$ of the heating temperature and 10 minutes of the maintaining pressure time at the pressure of 30kgf/$cm^2$. The produced composites showed 9 times higher density for small specimen, 6.6 times for actual size sample and great increase in bending strength from 102.05N/$mm^2$ to 189.47N/$mm^2$ for small size sample and to 205.4N/$mm^2$ for actual size sample, also great increase in hardness from 15.1N/$mm^2$ to 73.38N/$mm^2$ for small size sample and 64.87N/$mm^2$ for actual size sample. And the composites demonstrated great decrease in abrasion depth and in water absorption.

• 한국재료학회지
• /
• 제20권9호
• /
• pp.467-471
• /
• 2010

Composites of ceramic powders and an elastomer-based matrix were prepared by mixing $CaCO_3$ powders with polyethylene and polypropylene elastomers, and their mechanical and sound insulation properties were measured. $CaCO_3$ powders with 0.7 ${\mu}m$ and 35 ${\mu}m$ particle size were added to elastomers up to 80 wt%. Scanning electron microscopy photographs showed uniform distribution of the $CaCO_3$ powders in the matrix. While density and surface hardness increased, melt index, tensile strength and elongation of the composites decreased as the amount of added $CaCO_3$ powders increased. As more $CaCO_3$ powders were added sound transmission loss of the composites increased owing to the increase of density. Addition of 0.7 ${\mu}m$ sized $CaCO_3$ powders resulted in a slightly higher transmission loss than the addition of 35 ${\mu}m$ sized powders because of the increased interface area between the elastomer matrix and the $CaCO_3$ powders. Composites with a polyethylene matrix showed higher transmission loss than those with a polypropylene matrix because the tensile strength and hardness of the polyethylene-based composites were low and their elongation was high.

• 한국세라믹학회지
• /
• 제32권12호
• /
• pp.1392-1400
• /
• 1995

WC-10wt%Co-Al2O3 ceramic composites, using both the SHS (Self-propagating High Temperature Synthesis) synthesized WC powder method and commercial WC powder, were prepared by varing WC-Co/Al2O3 vol% ratio and sintering temperature (1350℃∼1650℃) for 1 hr in Ar atmosphere. Mechanical characterization has been investigated by Instron meterial testing system and Vicker's hardness test. Compositional and structural chracterizations were carried out by energy-dispersive analysis of X-ray (EDAX) data and scanning electron microscope (SEM). Electrical characterization was carried out by the electrical resistivity measurement using 4-point probe method. As sintering period increased and Al2O3 contents decreased in WC-10wt%Co-Al2O3 ceramic composite, shrinkage and relative density increased, resulting in maximum values at 1600℃. Also the major matrix phase changed with increasing Al2O3 content from 0 to 100 vol%. It was also identified by SEM, EDAX, and electrical resistivity measurement. Based on the results of analysis of flexural strength, toughness and hardness, the mechanical properties of WC-10wt%Co-Al2O3 ceramic composites using the SHS synthesized WC powder were better than those WC-10wt%Co-Al2O3 ceramic composites using commercial WC powder because WC-10wt%Co-Al2O3 ceramic composites using the SHS synthesized WC powder were sintered very well due to small initial particle size. By the addition of 40 vol% Al2O3 [60(WC=10wt%Co)-40Al2O3], it was possible to obtain a proper candidate as a superalloy.

• Composites Research
• /
• 제15권3호
• /
• pp.1-10
• /
• 2002

무가압함침법에 의해 제조된 SiCp/AC8A복합재료에 대하여 SiC 입자 크기와 부가적인 Mg의 첨가가 복합재료의 기계적 성질과 마모특성에 미치는 영향을 조사하였다. SiCp/AC8A복합재료의 경도와 굽힘강도는 입자의 크기가 작아짐에 따라 증가하였다. Mg 첨가량이 증가함에 따라 SiCP/AC8A복합재료의 경도는 경질의 반응생성물에 의해 상승하였으나 굽힘강도는 석출물의 조대화와 기공율의 증대에 의해 저하하였다. SiCp/AC8A복합재료는 AC8A 기지재에 비하여 고속의 마찰속도에서 6배의 내마모성을 나타냈으며 강화입자의 크기가 작아짐에 따라 내마모성은 향상되는 것으로 나타났다. 마모기구에 있어서 SiCp/AC8A복합재료는 마찰속도에 관계없이 연삭마모를 나타냈으나 AC8A 기지재는 마찰속도가 고속화됨에 따라 응착 및 용융마모의 마모면을 나타냈다.

• 한국세라믹학회지
• /
• 제34권5호
• /
• pp.491-499
• /
• 1997

High flexible lightweight composites containing tobermorite as a main mineral is produced using various amorphous silicates, lime, cement and fibers. Here, Mechanical properties of the composites were studied by observing microstructures of hydrates and fibers. Amorphous silicates having better hydraulicity retarded the crystallization of tobermorite due to better formation of C-S-H gel in water bath curing, but, difficult conversion from C-S-H gel to tobermorite in hydrothermal reaction. In the low molar ratio of CaO/SiO2 (0.67), faster crystalization was observed dued to more impurities such as Al2O3 alkali, resulting in improving mechanical properties due to small crystal size and many contact points. It was identified that a lot of calcium silicate hydates formed at surface of pulps increase bonding strength and the crack-resistance of matrix in the composites, but decrease hardness and compressive strength. The choice of amorpous silicates having better hydraulicity, low CaO/SiO2 adding each fibers bellow about 5% in the raw mixs and lower molding pressure should be needed at improve mechanical properties of composites.

• 한국세라믹학회지
• /
• 제36권4호
• /
• pp.451-458
• /
• 1999

TiC-Mo2C composites were prepared from Ti-C-Mo system by HPCS which has a great advantage of simulataneous synthesis and sintering In this study physical properties and microstructures of the com-posites were measured and observed to compare the sintering effects of Ni and Co each other : The results showed that the role of 5 wt% Ni in the sintering of the carbide composites was superior to that of 5wt% Co and the optimum content of Mo in the Ti-C-Mo system was 20wt% The carbide composites prepared under these two conditions had the best properties with 1.0% in apparent porosity 97.6% in relative density 19.1GPa in Vickers hardness and 5.3MPa$.$m1/2 in fracture toughness.

• 소성∙가공
• /
• 제10권3호
• /
• pp.223-234
• /
• 2001

The characteristics of thixoforming process can decrease liquid segregation because of the improvement in fluidity in a globular microstructure state and utilizes flow without an air entrapment. Therefore, in order to obtain the sound parts of metal matrix composites by using thixoforming process which has co-existing solidus-liquidus phase, it is very important to design a die shape property and to obtain the fabrication conditions which affect the unifomity of the solid fraction on unfilling state and various defects throughout the fabricated parts. The die designs and fabrication conditions to obtain the good piston part are proposed for thixoforging process of metal matrix composites. When reheated metal matrix composites billets were transferred to the closed die gate, thixoforging were carried out under the various pressure(60, 80, 100MPa) with controled forging speed. The mechanical properties such as hardness and tensile strength for thixoforged parts have been investigated after T6 heat treatment.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.35-38
• /
• 2004

Graphite nanofiber (GNF) and carbon nanotube (CNT) are novel fiber reinforcing materials which have outstanding physical and mechanical properties. Aluminum matrix composites reinforced graphite nanofiber were fabricated by conventional powder metallurgy (PM) method. The composites were prepared through ultrasonication, ball milling, and hot isostatic pressing. A uniform distribution of GNF in aluminum matrix could be obtained. To measure the mechanical properties of GNF-Al composites testings were done in indentation and compression. The compressive strength was enhanced according to reinforcing graphite nanofiber while the hardness was decreased. This study makes the high performance composites for future applications.