• Restorative Dentistry and Endodontics
• /
• v.25 no.3
• /
• pp.371-380
• /
• 2000

The effect of fiber reinforcing materials on the fracture strength of composite resin was evaluated. Each ten composite resin bars reinforced by glassfiber[Fiber-Splint ML$^{(R)}$(Polydentia SA, Switzerland)], polyethylene fiber [Ribbond$^{(R)}$(Ribbond Inc., U.S.A.)] and polyaramid fiber[Kevlar$^{(R)}$(DuPont, U.S.A.)] were loaded under the 3-point compression technique. Another ten pure composite resin bars without reinforcement were used as a control group. Then mean fracture strength and standard deviation were calculated and a ANOVA and Scheffe test were used in statistics. The results were as follows: 1. Kevlar group showed the highest fracture strength as 175.5MPa (p<0.05). Fiber-Splint ML group showed the lowest fracture strength as 112.7MPa. 2. The mean value of fracture strength in Ribbond group was 136.4MPa, and that of unterated control group was 143.6MPa. No difference was found between the two groups. 3. Ribbond and Kevlar reinforcement groups showed a catastrophic failure, where complete separation of pieces occurs to a unseparated fracture pattern. The use of Kevlar reinforcement fibers with composite resin showed significant increase in the average load failure and the presence of the fibers did prevent the catastrophic crack propagation present in the unreinforced samples. The use of Ribbond reinforcement fibers with composite resin showed no significant increase in the average load failure. However, the presence of the fibers did prevent the catastrophic crack propagation. Because high strength of glassfiber are rapidly degraded on exposure to moisture and humidity. The use of Fiber-Splint ML reinforcement fibers with composite resin showed significant decrease in the average load failure and displayed catastrophic fractures.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.1
• /
• pp.62-68
• /
• 1999

One of the many dilemmas that the clinical restorative dentist must face is treating young adolescent patient who prematurely loses his permanent teeth. Temporary prosthetic replacement can be achieved with removable denture, orthodontic band-wire fixed denture, adhesion bridge, composite resin splint with reinforcing material until the patients go through growth and development. But, all of these have limitations. Advances in restorative materials and reinforcement materials have made possible new techniques which are as much esthetic, conservative and more economic and stronger than adhesion brides. Two cases are being presented where gas-plasma treated, woven polyethylene fabric to reinforce composite resin was used to fabricate a temporary prosthetic restoration to replace a missing maxillary central incisor. This relatively noninvasive and basically reversible procedure allows the patient to decide the final restoration as he or she goes thorough maturation of the hard and soft tissues.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.21 no.2
• /
• pp.593-598
• /
• 1994

There were two cases of esthetic improvement of discolored teeth. First case was 12-year-old girl whose upper right central incisor was discolored after traumatic injury. She was treated by walking bleaching technique. Endodontic retreatment was done, and then the mixture of Superoxol and sodium perborate was applied and changed every week. After 3 weeks, esthetic result was obtained and fracture site was rcovered with light-curing composite resin. Second cases was 11-year-old girl whose teeth were discolored by fluorosis. She was treated by vital bleaching technique. A resin splint was made and then 30% and 15% carbamide peroxide was applied using this splint. After 4 weeks, a noticeable improvement in the color and the brightness of the teeth was achieved.

• The Journal of Korea Assosiation for Disability and Oral Health
• /
• v.13 no.1
• /
• pp.43-46
• /
• 2017

Patients with cerebral palsy have higher risk of traumatic dental injuries because of clinical characteristics, such as, ataxia, large overjet and lip incompetency. Especially, intrusive luxation has rare occurrence but higher incidence of complications. It can be treated by expecting re-eruption, orthodontic reposition, and surgical reposition. Clinicians should be aware of management and follow-up in dealing with cerebral palsy patients who are exposed by intrusive luxation, due to their involuntary movement. This case report describes a 9-year-old male patient with cerebral palsy and epilepsy who experienced intrusion of maxillary permanent central incisor. After one-month follow-up, waiting for spontaneous eruption, pulp necrosis on maxillary permanent central incisor had proceeded. Therefore, surgical reposition with resin wire splint and apexification was performed under conscious sedation with midazolam. After two months, removal of resin wire splint was done. Gutta percha filling and composite resin restoration were performed after sixteen months. During five-year follow-up ankylosis and partial root resorption were observed. But there was no significant complications.

• The korean journal of orthodontics
• /
• v.43 no.4
• /
• pp.186-192
• /
• 2013

Objective: To analyze the fatigue resistance, debonding force, and failure type of fiber-reinforced composite, polyethylene ribbon-reinforced, and braided stainless steel wire lingual retainers in vitro. Methods: Roots of human mandibular central incisors were covered with silicone, mimicking the periodontal ligament, and embedded in polymethylmethacrylate. The specimens (N = 50), with two teeth each, were randomly divided into five groups (n = 10/group) according to the retainer materials: (1) Interlig (E-glass), (2) everStick Ortho (E-glass), (3) DentaPreg Splint (S2-glass), (4) Ribbond (polyethylene), and (5) Quad Cat wire (stainless steel). After the recommended adhesive procedures, the retainers were bonded to the teeth by using flowable composite resin (Tetric Flow). The teeth were subjected to 10,00,000 cyclic loads (8 Hz, 3 - 100 N, $45^{\circ}$ angle, under $37{\pm}3^{\circ}C$ water) at their incisoproximal contact, and debonding forces were measured with a universal testing machine (1 mm/min crosshead speed). Failure sites were examined under a stereomicroscope (${\times}40$ magnification). Data were analyzed by one-way analysis of variance. Results: All the specimens survived the cyclic loading. Their mean debonding forces were not significantly different (p > 0.05). The DentaPreg Splint group (80%) showed the highest incidence of complete adhesive debonding, followed by the Interlig group (60%). The everStick Ortho group (80%) presented predominantly partial adhesive debonding. The Quad Cat wire group (50%) presented overlying composite detachment. Conclusions: Cyclic loading did not cause debonding. The retainers presented similar debonding forces but different failure types. Braided stainless steel wire retainers presented the most repairable failure type.

• Journal of Veterinary Clinics
• /
• v.35 no.4
• /
• pp.137-140
• /
• 2018

A five-month-old toy poodle was referred for treatment of bilateral mandibular fractures. Preoperative skull and dental radiographs showed rostral mandibular fractures and permanent teeth that had not yet erupted. In addition to providing stability for the healing of fractures, it is very important to focus on restoring normal occlusion. The mandibular fractures were repaired using interdental wiring in a dentate area where the deciduous canines and fourth premolars were stable and could be used to anchor the interdental fixation. In the absence of an erupted permanent mandibular first molar, the modified Risdon wiring was performed using the deciduous mandibular fourth premolars as anchor teeth. An intraoral splint was placed on the mandibular teeth using self-curing composite resin. Five months after surgery, the patient had experienced no complications, and the permanent teeth had erupted normally. In this case, which involves a small-breed puppy with deciduous dentition, treatment with a wire-reinforced interdental splint using intact deciduous fourth premolar teeth as anchor teeth can be considered as a suitable method for rostral mandibular fracture restoration.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.34 no.4
• /
• pp.290-296
• /
• 2018

Purpose: The aim of this study was to evaluate the polymerization ability of resin-based materials used for teeth splinting according to the thickness of cure. Materials and Methods: For this study, the Light-Fix and G-FIX developed for resinous splinting materials and the G-aenial Universal Flo, the high-flowable composite resin available as restorative and splinting material, were used. Ten specimens of the thickness of 2, 3, 4 and 5 mm and 5 mm in diameter for each composite resin (total 120) were prepared. The microhardness of top and bottom surfaces for each specimen was measured by the Vickers hardness testing machine. The polymerization ability of the composite resin for each thickness was statistically analyzed using independent T-test at a 0.05 level of significance. Results: There was no difference of polymerization ability regardless of the thickness in the Light-Fix and G-FIX. The G-aenial Universal Flo showed significantly low polymerization ability from the thickness of the 3 mm (P < 0.05). Conclusion: The Light-Fix and G-FIX, which are resin-based materials used for teeth splinting, are expected to be suitable for light curing up to 5 mm in thickness.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.32 no.3
• /
• pp.169-175
• /
• 2016

Purpose: Direct splinting material should have high flexural strength to withstand force during mastication and low modulus of elasticity to provide some movement while force applied for relief of stress. The purpose of this study was to compare flexural strength and modulus of elasticity of several resinous splinting materials. Materials and Methods: Four materials; Super-Bond C&B, G-FIX, G-aenial Universal Flo, FiltekTM Z350 XT; were used in this study. Fifteen rectangular bar specimens of each material were prepared. Three-point bending test were performed to determine physical properties. Maximum load at fracture was recorded and flexural strength and modulus of elasticity were calculated. One-way analysis of variance (ANOVA) and Scheffe's tests at a 0.05 level of significance were conducted on all test results. Results: Statistical analysis reveals that Super-Bond C&B had significant low mean value for flexible strength and the other three materials showed no significant difference. For modulus of elasticity, Super-Bond C&B exhibited statistically lower modulus of elasticity. G-FIX presented intermediate result, showing statistically higher modulus of elasticity than Super-Bond C&B but lower than G-aenial Universal Flo and FiltekTM Z350 XT. There was no significant difference on modulus of elasticity between G-aenial Universal Flo and FiltekTM Z350 XT. Conclusion: Using a G-FIX, the newly commercially available splinting material, which shows higher fracture resistance properties comparable to flowable and restorative composite resin and a relatively flexible nature might be a beneficial for stabilizing teeth mobility.