• Steel and Composite Structures
• /
• v.11 no.2
• /
• pp.149-168
• /
• 2011

This paper presents a computational study of column loss scenarios for typical multi-story steel buildings with perimeter moment frames and composite steel-concrete floors. Two prototype buildings (three-story and ten-story) were represented using three-dimensional nonlinear finite element models and explicit dynamic analysis was used to simulate instantaneous loss of a first-story column. Twelve individual column loss scenarios were investigated in the three-story building and four in the ten-story building. This study provides insight into: three-dimensional load redistribution patterns; demands on the steel deck, concrete slab, connections and members; and the impact of framing configuration, building height and column loss location. In the dynamic simulations, demands were least severe for perimeter columns within a moment frame, but the structures also exhibited significant load redistribution for interior column loss scenarios that had no moment connectivity. Composite action was observed to be an important load redistribution mechanism following column loss and the concrete slab and steel deck were subjected to high localized stresses as a result of the composite action. In general, the steel buildings that were evaluated in this study demonstrated appreciable robustness.

• Computers and Concrete
• /
• v.22 no.3
• /
• pp.269-278
• /
• 2018

In the recent decades, the application of composite materials, due to their desirable properties, has increased dramatically. In the present study, a quasi-encased trapezoidal section composite steel beam encased with concrete is thoroughly examined. Calculation of the load bearing capacity is carried out by finite element modeling of concrete and FRP beams with trapezoidal section under the effect of controlled displacement loading. The results are then validated comparing to the existing experimental results obtained from similar studies. Further on, the materials are changed to steel and concrete, and the section is de-signed in such a way that both concrete and steel reach a high percent-age of their load bearing capacity. In the last step, the parameters affecting the bending capacity and the behavior of the semi-confined composite beam are investigated. Results revealed that the beam diagonal web thickness plays the most effective role in load bearing capacity amongst other studied parameters. Furthermore, by analyzing the results on the effect of different parameters, an optimal model for primary beam section is presented, which exhibits a greater load bearing capacity compared to the initial design with the same amount of materials used for both sections.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.78-83
• /
• 2015

In the composite case, the first ply failure is considered total failure of the case. When the case is constructed by filament winding over a metal liner, the first ply failure does not necessarily mean total failure of the case. In this study, we compared the results through finite element analysis and burst test to predict the burst pressure of the hybrid case (filament-wound composite case with metal liner). Through it predicts the burst pressure of the hybrid case, we can determine the thickness of the metal liner and composite.

• Composites Research
• /
• v.29 no.6
• /
• pp.363-368
• /
• 2016

This study performed a nonlinear finite element crash analysis of guardrail structures using supports made of composite materials. In this study, we used a new [0/90/90/0] laminated Boron fiber composite for resisting the crash effects. Based on the improved ground-structure interaction model, appropriate ground properties to the support were determined. In particular, the complex crash mechanism of guardrails was studied using various parameters. The parametric studies are focused on the various effects of car crash on the structural performance and thickness of supports. The numerical results for various parameters are verified by comparing those using existing steel materials.

• Steel and Composite Structures
• /
• v.17 no.3
• /
• pp.237-252
• /
• 2014

The use of composite structures is increasingly present in civil building works. Composite Box Girder Bridges (CBGB), particularly, are study of effect of shear connector's numbers and distribution on the behavior of CBGBs is submitted. A Predicti structures consisting of two materials, both connected by metal devices known as shear connectors. The main functions of these connectors are to allow for the joint behavior of the girder-deck, to restrict longitudinal slipping and uplifting at the element's interface and to take shear forces. This paper presents 3D numerical models of CBGBs to simulate their actual structural behavior, with emphasis on the girder-deck interface. Additionally, a Prediction of several FE models is assessed against the results acquired from a field test. A number of factors are considered, and confirmed through experiments, especially full shear connections, which are obviously essential in composite box girder. A good representation for shear connectors by suitable element type is considered. Numerical predictions of vertical displacements at critical sections fit fairly well with those evaluated experimentally. The agreement between the FE models and the experimental models show that the FE model can aid engineers in design practices of box girder bridges. Preliminary results indicate that number of shear studs can be significantly reduced to facilitate adoption of a new arrangement in modeling CBGBs with full composition. However, a further feasibility study to investigate the practical and economic aspects of such a remedy is recommended, and it may represent partial composition in such modeling.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.4 s.70
• /
• pp.427-434
• /
• 2005

In this study, to develop composite bridge deck of many advantages such as light weight, high strength, corrosion resistance and high durability, profile design, laminate design and finite element analysis were carried out. In the analysis, 5-girder single span bridge with composite deck was considered. Deflection serviceability, failure criteria and web buckling were evaluated. Composite deck of designed profile was fabricated with pultrusion process. The coupon tests were conducted for the fabricated deck and the results were described.

• Steel and Composite Structures
• /
• v.36 no.5
• /
• pp.569-586
• /
• 2020

The behavior of composite steel-concrete beams depends on the transmission of forces between two parts: the concrete slab and the steel I-beam. The shear connector is responsible for the interaction between these two parts. Recently, an alternative shear connector, called Truss Type connector, has been developed; it aligns efficient structural behavior, fast construction and implementation, and low cost when compared to conventional connectors applied in composite structures. However, there is still a lack of full understanding of the mechanical behavior of the Truss Type connector, due to its novelty. Thus, this study aims to analyze the influence of variation of geometric and physical parameters on the shear resistance of the Truss Type connector. In order to investigate those parameters, a non-linear finite element model, able to simulate push-out tests of Truss Type connectors, was specifically developed and validated with experimental results. A thorough parametric study, varying the height, the angle between rods, the diameter, and the concrete strength, was conducted to evaluate the shear resistance of the Truss Type connector. In addition, an equation to predict the resistance of the original Truss Type shear connector was proposed.

• Composites Research
• /
• v.28 no.2
• /
• pp.65-69
• /
• 2015

This study dealt with dynamic characteristics by real car crash simulation of composite support structures for road facilities. The effects of different material properties of composites for various car crash speeds are studied using the LS-DYNA finite element program for this study. In this study, the existing finite element analysis of steel support structures using the LS-DYNA program is further extended to study dynamic behaviors of the support structures made of various composite materials. Based on the passenger safety assessment, the numerical results for various parameters are verified by comparing different models with internal energy occurred in the support and car.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.1
• /
• pp.1-7
• /
• 2015

This paper predicts the spring-in effect of curved laminated composite structure for various stacking sequence using finite element analysis(ABAQUS). In composite manufacturing process, large temperature difference, different coefficient of thermal expansion and chemical shrinkage effect cause distortion of composite parts such as spring-in and warpage. Distortion of composite structure is important issue on quality of product, and it should be considered in manufacturing process. In finite element analysis, a CHILE(Cure Hardening Instantaneously Linear Elastic) model and chemical shrinkage effects are considered developing user subroutine in ABAQUS and some cases are simulated.

• Steel and Composite Structures
• /
• v.4 no.6
• /
• pp.489-507
• /
• 2004

The flexibility of the connection between steel and concrete largely influences the global behaviour of the composite beam. Therefore the way the connection is modelled is the key issue in its structural analysis. Here we present a new strain-based finite element formulation in which we consider non-linear material and contact models. The computational efficiency and accuracy of the formulation is proved with the comparison of our numerical results with the experimental results of Abdel Aziz (1986) obtained in a full-scale laboratory test. The shear connectors are assumed to follow a non-linear load-slip relationship proposed by Ollgaard et al. (1971). We introduce the notion of the generalized slip, which offers a better physical interpretation of the behaviour of the contact and gives an additional material slip parameter. An excellent agreement of experimental and numerical results is obtained, using only a few finite elements. This demonstrates that the present numerical approach is appropriate for the evaluation of behaviour of planar composite beams and perfect for practical calculations.