• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.1989-2000
• /
• 2015

In this paper, digital peak current mode control for single phase H-bridge inverters is developed and implemented. The digital peak current mode control is achieved by directly controlling the PWM signals by cycle-by-cycle current limitation. Unlike the DC-DC converter where the output voltage always remains in the positive region, the output of DC-AC inverter flips from positive to negative region continuously. Therefore, when the inverter operates in negative region, the control should be changed to valley current mode control. Thus, a novel control logic circuit is required for the function and need to be analyzed for the hardware to track the sinusoidal reference in both regions. The problem of sub-harmonic instability which is inherent with peak current mode control is also addressed, and then proposes the digital slope compensation in constant-sloped external ramp to suppress the oscillation. For unipolar PWM switching method, an adaptive slope compensation in digital manner is also proposed. In this paper, the operating principles and design guidelines of the proposed scheme are presented, along with the performance analysis and numerical simulation. Also, a 200W inverter hardware prototype has been implemented for experimental verification of the proposed controller scheme.

• Journal of Power Electronics
• /
• v.14 no.1
• /
• pp.40-47
• /
• 2014

An average current mode control scheme that consistently offers good dynamic performance for LLC series resonant DC-to-DC converters irrespective of the changes in the operational conditions is presented in this paper. The proposed control scheme employs current feedback from the resonant tank circuit through an integrator-type compensation amplifier to improve the dynamic performance and enhance the noise immunity and reliability of the feedback controller. Design guidelines are provided for both current feedback and voltage feedback compensation. The performance of the new control scheme is demonstrated through an experimental 150 W converter operating with 340 V to 390 V input voltage to provide a 24 V output voltage.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.100-109
• /
• 2017

This paper proposes performance improvement schemes for sensorless PMSM control drive using a four-switch three-phase inverter (so-called B4 inverter). In the proposed scheme, the back-EMF estimation-based sensorless control algorithm is used to control the brushless PMSM without position sensors. In order to have stable operation, this paper presents a gain adjustment scheme that compensates the reduction of stable sensorless operation range as long as the rotor speed increases. In B4 topology, the center point of dc-link capacitors is connected to 3-phase load, and it is prone to have the load current distortion. Hence, to mitigate this problem, a distortion compensation scheme by modifying voltage commands using measured dc-link potentials is proposed in this paper. The validity of the proposed method is evaluated by simulations and experiments.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.7
• /
• pp.703-710
• /
• 2007

This paper presents an attitude determination scheme for the Science and Technology Satellite-2(STSAT-2) using Fine Digital Sun Sensor(FDSS). The FDSS has been developed for STSAT-2, and exhibits the accuracy of 0.032degree in $1{\sigma}$. To be specific, the attitude information from the sensor is exploited to compensate for Fiber Optic Gyro(FOG) mounted on STSAT-2, and Kalman filter model is derived and implemented. To show the effectiveness of the present compensation scheme, computer simulations have been carried out resulting in the attitude errors within a bound.

• Journal of Power Electronics
• /
• v.12 no.1
• /
• pp.58-66
• /
• 2012

SRMs(Switched Reluctance Motors) are much interested in high speed applications due to the mechanical robustness, simple structure and high efficiency. In spite of many advantages of SRMs, a higher torque ripple discourages the adoption of SRMs in a high speed application. This paper presents a simple negative torque of tail current compensation scheme using a modified TSF(Torque Sharing Function) for the high speed SRMs. Because of the short commutation in the high speed region, the negative torque from the tail current makes the high torque ripple. In order to reduce and compensate the negative torque from tail current, the proposed control scheme produces an additional compensating torque with a reference torque in the active phase winding. And the compensating value is dependent on the tail current of the inactive phase winding. Furthermore, the switching signals of the outgoing phase are fully turned off to restrict the extended tail current, and the torque error of the outgoing phase is compensated by the incoming phase. The proposed modified TSF control scheme is verified by the computer simulations with 30,000[rpm] high speed 4/2 SRM. The simulation and experimental results show the effectiveness of the proposed control scheme.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.12C
• /
• pp.1029-1034
• /
• 2010

For All Digital QPSK receivers, a phase recovery scheme is required to fix the arbitrarily rotated I/Q quadrature signals due to the transmission path and clock mismatch between the transmitter and the receiver. The conventional Costas phase recovery loop scheme requires a separate AGC(Automatic Gain Control) to obtain the performance independent of input signal power. This paper proposes a simple scheme which separates the phase and amplitude of the input signal via CORDIC algorithm and performs the phase recovery and amplitude compensation simultaneously. The proposed scheme can considerably reduce the logic resources in hardware implementation, has been verified by C++ and Model Sim simulations.

• Journal of Arbitration Studies
• /
• v.22 no.1
• /
• pp.43-63
• /
• 2012

Media ADR is currently emerging as one of successful cases in South Korea while environmental ADR was known not to satisfy both defendants and offenders. Thus, this paper is intended to present proper remedies for typical compensation schemes of environmental ADR by comparing the two ADRs regarding legal reservation of compensation clause. It was found that the media ADR helped clients achieve a more fast and easy dispute resolution by providing compensation standards based on various categories such as types and scopes of compensation. However, the compensation scheme of environmental ADR brought out public complaints and inadequate services due to inconsistency and instability in terms of legal reservation. The results indicate that the compensation clause based on the reservation of laws in media ADR could be used not only as a checklist to confirm limitations of environmental ADR, but also as realistic evidences to adjust the compensation standard systematically that is under development and requires remodelling. As a result, the research findings have opened the new possibilities of "the quality assurance of environmental ADR based on the domestic legislation", proposed as an initial aim of this paper.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.597-600
• /
• 1997

In this paper, the authors propose a new method for linearizing a nonlinear dynamical system by use of polynomial compensation. In this method, an M-sequence is applied to the nonlinear system and the crosscorrelation function between the input and the output gives us every crosssections of Volterra kernels of the nonlinear system up to 3rd order. We construct a polynomial compensation function from comparison between lst order Volterra kernel and high order kernels. The polynomial compensation function is, in this case, of third order whose coefficients are variable depending on the amplitude of the input signal. Once we can get compensation function of nonlinear system, we can construct a linearization scheme of the nonlinear system. That is. the effect of second and third order Volterra kernels are subtracted from the output, thus we obtain a sort of linearized output. The authors applied this method to a saturation-type nonlinear system by simulation, and the results show good agreement with the theoretical considerations.

• ETRI Journal
• /
• v.26 no.5
• /
• pp.501-504
• /
• 2004

This paper presents a simple gain/phase blind compensation algorithm with an automatic gain control (AGC) function for the adoption of the AGC function and compensation for gain/phase imbalances in quadrature phase shift keying (QPSK) direct conversion receivers (DCRs). The AGC function is interactively operated with the compensation algorithm for gain/phase imbalances. By detecting the gain sum and difference values between the I-channel and Q-channel, the combined AGC and gain imbalance compensation algorithm provides a simpler DCR architecture.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.315-319
• /
• 2011

A switched-capacitor cyclic DAC scheme with mismatch compensation of capacitors is designed. In cyclic DAC, a little error between two capacitors is accumulated every cycle. As a result, the accumulated error influences the final analog output which is wrong data. Therefore, a mismatch compensation technique was proposed and the error can be effectively reduced, which alleviates the matching requirement. In order to verify the operation of the proposed DAC, an 8-bit switched-capacitor cyclic DAC is designed through HSPICE simulation and implemented through magna 0.18um standard CMOS process.