• Journal of Aerospace System Engineering
• /
• v.4 no.3
• /
• pp.24-28
• /
• 2010

The purpose of this study is to define available microwave absorbing structure for aircraft from in the X-band(8.2~12.4GHz) frequencies. The electromagnetic wave absorption or shielding techniques is an important issue not only for military purpose but also for commercial purposes. Aircraft Radar Absorbing Structure(RAS) is absorbed or scattered propagation waves from the enemy radar. There are absorbing technologies at shaping design techniques and using Radar Absorbing Materials(RAM). RAM is more important because shaping design can't include perfect radar absorbing performance. In this study, based on material properties was introduced RAM and to analyze the each characteristics. Finally, we comparison appropriate RAM for aircraft.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.3
• /
• pp.57-68
• /
• 2012

In this study, designs of the high efficiency composite propeller blade for a high speed turboprop aircraft, which will be used for a next generation regional commercial aircraft in Korea, are performed. Both the vortex theory and the blade element theory are used for preliminary aerodynamic design and performance analysis of the propeller. Then the aerodynamic design result is confirmed through performance analysis using a commercial CFD code, ANSYS. The carbon/epoxy composite materials is used, and the skin-spar-foam sandwich type structure is adopted for improvement of lightness and structural stability. Finally, it is investigated that the proposed propeller blade has high efficiency and structural safety through both aerodynamic and structural analysis and experimental test of a prototype propeller blade.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.2
• /
• pp.189-196
• /
• 2014

Automated design program using commercial process integration and optimization program was developed for conceptual design of fighter-class aircraft. Wind tunnel test data and performance analysis results were compared for the verification of analysis tool of this program, and the usefulness of the tool was found. After integration with radar cross section analysis tool, the correlation with configuration design variables of wing, tail and performance parameters was identified by design of experiment, and the optimized configuration for weight and RCS was derived from optimization of empty weight and average frontal RCS value. After parameter definition of fuselage, the program can be implemented for full aircraft configuration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.253-258
• /
• 2012

In this study, designs of the high efficiency composite propeller blade for a high speed turboprop aircraft, which will be used for a next generation regional commercial aircraft in Korea, are performed. Both the vortex theory and the blade element theory are used for preliminary aerodynamic design and performance analysis of the propeller. Then the aerodynamic design result is confirmed through performance analysis using a commercial CFD code, ANSYS. The carbon/epoxy composite materials is used, and the skin-spar-foam sandwich type structure is adopted for improvement of lightness and structural stability. Finally, it is investigated that the proposed propeller blade has high efficiency and structural safety through both aerodynamic and structural analysis and experimental test of a prototype propeller blade.

• The Korean Journal of Air & Space Law and Policy
• /
• v.27 no.2
• /
• pp.107-142
• /
• 2012

An aircraft has been one of the most important transportation means and disputes due to damage caused by delay of the aircraft happen many times out of ones related to the air transport. In 2011, the Air Transport Act in Commercial Law was established to regulate national air transport and the legislative system of air carrier's liability to handle delay of passengers or baggage was legislated here. Although there are some clauses related to the legislative system of air carrier's liability, they are very important because they deal with disputes due to damage caused by delay of the aircraft. The Air Transport Act in Commercial Law has a good point of adopting the global standard of 1999 Montreal Convention, but it has also a bad point of having the problems of 1999 Montreal Convention. There are some contents to be modified in the Air Transport Act in Commercial Law. First, the definition of 'Delay of Aircraft' needs to be enacted because it is important to materialize air carrier's liability due to damage caused by delay. Second, it is necessary to modify the clause in which air carrier's liability due to damage caused by delay of passengers is divided into two things, one is in case of national air transport and the other is in case of international air transport, and the limited amount of air carrier's liability in national air transport is eight times less than the latter because they are not so helpful to air carriers but too disadvantageous to aircraft passengers. Third, it is also necessary to amend the clause in which the limited amount of air carrier's liability due to damage caused by loss damage or delay of baggage has been legislated same without classifying the case into loss damage and delay, because they are generally different from each other in terms of extent of damage, therefore the limited amount of air carrier's liability by delay of baggage should be classified into in case of loss damage and in case of delay. It is desired that the Air Transport Act in Commercial Law including the clauses related to air carrier's liability by aircraft damage be developed continually by sufficient study and discussion about the necessity of amending it such as the one mentioned above.

• Journal of Mechanical Science and Technology
• /
• v.15 no.6
• /
• pp.776-787
• /
• 2001

The turbofan engine performance analysis for a medium scale commercial aircraft was carried out and the LQR control scheme for performance optimization was studied. By using scaled component maps from well-known CF6 engine characteristics, the steady-state performance analysis result was compared with BR715-56 engine performance data. The transient performance analysis was performed with four fuel schedules. The linear simulation was done at the maximum take-off condition. The real time linear simulation was performed by interpolation of the system matrices, which used the least square method as the function of LPC rotational speed. By using linear system matrices of design point, the LQR controller which used control variables for the fuel flow and the LPC bleed air was designed.

• Advances in aircraft and spacecraft science
• /
• v.2 no.1
• /
• pp.95-108
• /
• 2015

Automatic Dependent Surveillance Broadcast (ADS-B) is quickly being adopted by aviation safety authorities around the world as the standard for aircraft tracking. The technology provides the opportunity for live tracking of aircraft positions within range of an ADS-B receiver stations. Currently these receiver stations are bound by land and local infrastructural constraints. As such there is little to no coverage over oceans and poles, over which many commercial flights routinely travel. A low cost space based ADS-B receiving system is proposed as a constellation of small satellites. The possibility for a link between aircraft and satellite is dependent primarily on proximity. Calculating the likelihood of a link between two moving targets when considering with the non-periodic and non-uniform nature of actual aircraft flight-paths is non-trivial. This analysis of the link likelihood and the performance of the tracking ability of the satellite constellation has been carried out by a direct simulation of satellites and aircraft. Parameters defining the constellation (satellite numbers, orbit size and shape, orbit configuration) were varied between reasonable limits. The recent MH370 disappearance was simulated and potential tracking and coverage was analysed using an example constellation. The trend of more satellites at a higher altitude inclined at 60 degrees was found to be the optimal solution.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.12 no.3
• /
• pp.41-63
• /
• 2004

The area covered by product liability in broadest sense is so vast that an attempt to analyse all its impact on the aviation world risk. Every effort has been made to confine our review of subject a closely as possible to its influence on aircraft manufacturers, airlines and passengers, in spite of strong connections with other spheres of commercial. Product Liability in aviation is the liability of aircraft's manufacturer, processor or non-manufacturing seller for injury to the person or property of a buyer or third party caused by a product which has been sold. Here-in a product is aircraft, third party is passengers who suffered damage by defective design, defective construction, inadequate instructions for handling in aircraft. Whenever a product turns out to be defective after it has been sold, there are under Anglo-American law three remedies available against the aircraft's manufacturer (1) liability for negligence (2) breach of warranty (3) strict liability in tort. There are Under continental law Three remedies available against the aircraft's manufacturer (1) liability for defective warranty (2) liability for non-fulfillment of obligation (3) liability in tort. It is worth pointing out here an action for breach of warranty or for defective warranty, for non-fulfillment of obligation is available only to direct purchaser on the basis of his contract with the aircraft's manufacturer, which of course weakness its range and effectiveness. An action for tort offers the advantage of being available also to third parties who have acquired the defective product at a later stage. In tort, obligations are constituted not only by contract, but also by stature and common law. In conclusion, There in no difference in principle of law. In conclusion I would like to make few suggestions regarding the product liability for aircraft's manufacturer. Firstly, current general product liability code does not specify whether government offices(e.g. FAA) inspector conducted the inspection and auditory certificate can qualify as conclusive legal evidence. These need to be clarified. Secondly, because Korea is gaining potential of becoming aircraft's manufacturer through co-manufacturing and subcontracting-manufacturing with the US and independent production, there needs legislation that can harmonize the protection of both aircraft's manufacturers and their injured parties. Since Korea is in primary stage of aviation industry, considerate policy cannot be overlooked for its protection and promotion. Thirdly, because aircraft manufacturers are risking restitution like air-carriers whose scope of restitution have widened to strict and unlimited liability, there needs importation of mandatory liability insurance and national warranty into the product liability for aircraft's manufacturers. Fourthly, there needs domestic legislation of air transportation law that clearly regulates overall legal relationship in air transportation such as carrier & aircraft manufacturer's liability, and aviation insurance.

• Journal of computational fluids engineering
• /
• v.13 no.4
• /
• pp.80-85
• /
• 2008

The prediction of the separation trajectories of external stores released from a military aircraft is an important task in the aircraft design area having the objective to define the operational and release envelopes. This paper presents the results obtained for store separation by employing commercial softwares, FLUENT and CFD-FASTRAN. FLUENT treats the rigid body motion by employing a remeshing scheme. CFD-FASTRAN uses Chimera(overset) grid and interpolations. It was found that, for the prediction of the trajectories and behavior of the stores separated from the wing, both codes show the good agreement with the experimental results.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.504-509
• /
• 2004

Chemical machining(CHM) is a special process which material removed by contact of strong etchant. The application as industrial process was started from aircraft industry after 2nd world war. Chemical milling, one of the CHM process, initially became commercial bussiness and it was called chem-mill. Even today, this process widely used to remove the material from aircraft wings and fuselage panel in aircraft industry. In this study, it is attempted to design the cylinder pattern which minimize the weight within the allowable stress using chemical milling.