• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.33-40
• /
• 2004

Combustion of coke/anthracite in an iron ore sintering bed is characterized quantitatively by introducing newly defined parameters related to propagation and thickness of combustion zone and maximum temperature. The parameters are obtained by sintering pot experiment and I-D, unsteady numerical model which treats solid material as multiple solid phases. Experiments and calculations are performed for various major operating parameters: air inlet velocity, different type of fuels which have different reactivity and diameter of the solid fuel. Effects of the operating parameters on the productivity and quality of the sintering process are investigated and evaluated quantitatively and the results show that optimized air supply rate and diameter of anthracite for replacement of coke can be obtained. This approach can be applied to other kinds of combustors for characterization of the combustion in the solid fuel beds.

• 한국연소학회지
• /
• 제11권4호
• /
• pp.1-8
• /
• 2006

The model cavity scramjet engine experiments are carried out using T3 free-piston shock tunnel. Upstream hydrogen fuel is injected before the cavity with different injection pressure. OH planar laser-induced fluorescence is used to investigate the combustion zone and piezoelectric pressure transducers are used to define the pressure rise due to the combustion. Main combustion region is a mixing layer which is between air and fuel. Also high OH fluorescence signal is appeared in the shear layer above the cavity in high equivalence ratio. From the OH signal in the cavity, this fuel injection system can be a role as a flame-holder.

• 한국연소학회지
• /
• 제17권2호
• /
• pp.24-31
• /
• 2012

Diesel engines exhaust much more NOx(Nitrogen Oxides) and PM(Particulate Matter) than gasoline engines, and it is not easy to reduce both NOx and PM simultaneously because of the trade-off relation between two components. This study investigated flame characteristics of the partial premixed compression ignition known as new combustion method which can reduce NOx and PM simultaneously. The investigation was performed through the analysis of the flame images taken by a high speed camera from the visible engine which is the modified single cylinder diesel engine. The results obtained through this investigation are summarized as follows; (1) The area of the luminous yellow flame was reduced due to the decrease of flame temperature and even distribution of temperature. (2) The darkish yellow flame zone caused by the shortage of the remaining oxygen after the middle stage of combustion was considerably reduced. (3) Since the ignition delay was shortened, the violent combustion did not occur and the combustion duration became shortened.

• 한국대기환경학회지
• /
• 제18권2호
• /
• pp.85-94
• /
• 2002

In this study, a 3-dimensional numerical model, has been developed applied for the investigation of combustion characteristics, and used to optimize operating conditions in MSW incinerator, in Gwangju. The model developed in this study has been verified by exacting both the predicted and the measured temperature in combustion chamber which has been operated to provide a reference condition. By predictive results, the Sangmoo incinerator has a good characteristics of combustion and low emission however after burning zone produced incomplete products, also probably because the supply of primary air was not enough. Parametric screening studies have been conducted to study optimal operating conditions. For the optimal combustion characteristics, operating conditions should be adjusted with the waste properties.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제24회 KOSCO SYMPOSIUM 논문집
• /
• pp.3-10
• /
• 2002

In this work, numerical parametric studies on spray combustion have been conducted. In simulation of turbulence, RNG ${\kappa}-{\varepsilon}model$ is adopted. Initial spray distribution is specified by Rosin-Rammler distribution function. Eddy break-up model is adopted as a combustion model. The parameters considered are inlet air temperature, swirl number, and SMD. With higher inlet air temperature, the axial velocities are increased and penetration of primary jet is stronger than that of lower inlet air temperature and temperature at the exit of combustor is more uniform. Combustion efficiency is improved with high inlet air temperature. The effect of swirl number on flow field is not significant. It affect only recirculation zone. So temperature at upstream of combustor is influenced. Combustion efficiency deteriorate as SMD of fuel spray increase.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.26-36
• /
• 2010

This paper provides a description of the combustion model to obtain an accurate dynamic engine phenomena that satisfies real-time simulation for model-based engine control. The combustion chamber is modeled as a storage device for mass and energy. The combustion process is modeled in terms of a two-zone model for the burned and unburned gas fractions. The mass fraction burnt is modeled in terms of a Wiebe function. The instantaneous net engine torque is calculated from the engine speed and the instantaneous piston work. The modeling accuracy has been tested with a cylinder pressure data on a test bench and also the ability of real-time simulation has been checked. The results show that combustion model yields sufficiently good performance for the model-based control logic design. However the influence factors effected on model accuracy are some room for improvement.

• 한국안전학회지
• /
• 제7권3호
• /
• pp.14-21
• /
• 1992

The smouldering combustion of cellulose insulation treated with boric acid-borax-alum as combustion retardants are examined by Candle type combustibility tester. This sequence was examined quantitatively for longitudinal cylinder bed of cellulose insulation. Two configuration are possible, downward and upward smoulder spread ; both were investigated exprimentally. The smoulder spread velocity of cellulose insulation was 2.5cm/s -5.0cm/s in smoulder region. As results of critical oxygen content measurement, the effectiveness of alum as third combustion retardant are acceptable for flaming retardant effect. The phenomena of combustion transition are governed by quantity of commbustible gas generation In heating zone of cellulose insulation. The critial oxygen content are decreased with the increase of gas flow rate.

• 항공우주시스템공학회지
• /
• 제3권4호
• /
• pp.41-49
• /
• 2009

This paper present result of numerical simulation of premixed combustion around a triangle Bluff Body. And a numerical simulation of a premixed flame stabilization by a bluff body was performed using LES Model. The calculated results from the LES showed a good agreement with experiment data than k-model. Premixture combustion has flammability limit, quenching distance, smallest ignition energy has the combustion quality of the back. Bluff body makes a recirculation zone. Therefor velocity of behind bluff body is very slow. It was caused by slowly position speed and the fire occurred after the Bluff Body. Occurrence of fire it made the waste gas of high speed and the thrust made well.

• 한국분무공학회지
• /
• 제3권2호
• /
• pp.42-50
• /
• 1998

The effect of swirl flows un the fuel spray characteristics were investigated for various swillers in a model combustor. The interaction between the flow field and fuel spray in the main combustion tone made by frontal devices including fuel injection nozzles and swirlers. which were characterized by flow velocities, fuel droplet sizes and their distributions which were measured by APV(Adaptive Phase/Doppler Velocimetry) under atmospheric condition at 320cc/min kerosine fuel flow and 0.04kg/sec air supply. A dual swirler with circumferential two-stage swirl vanes of $40^{\circ}\;and\;45^{\circ}$ vanes in different directions and two single-stage swillers of $40^{\circ}$ vanes with 12 and 16 vanes were tested. It was found that the dual swirler has the largest recirculating zone with highest reverse flow velocity. The strongest swirl flow was found at the boundary of recirculation zone. Small fuel droplets were observed in the main axial stream and inside the recirculation zone when swirling flow field were generated by the frontal devices. These findings could give the tips on the optimal design of frontal devices to realize low emissions in gas turbine combustion.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.1979-1983
• /
• 2008

The effects of carbon dioxide addition to oxygen have been investigated with swirl-stabilized premixed methane flame in a laboratory-scale pre-mixed combustor. The methane fuel and oxydant mixture gas ($CO_2$ and $O_2$) were mixed in a pre-mixer and introduced to the combustor through different degrees of swirl vanes. The flame characteristics were examined for different amount of carbon dioxide addition to the methane fuel and different swirl strengths. The effects of carbon dioxide addition and swirl intensity on the combustion characteristics of pre-mixed methane flames were examined using chemiluminescence techniques to provide information about flow field. The results show that the flame area increases at upstream of reaction zone because of increase in recirculation flow for increase in swirl intensity. The flame area is also increased at the downstream zone by recirculation flow because of increase in swirl intensity which results in higher centrifugal force. The OH and CH radical intensity of reaction zone decrease with carbon dioxide addition because the carbon dioxide plays a role of dilution gas in the reaction zone.