• Clean Technology
• /
• v.29 no.4
• /
• pp.321-326
• /
• 2023

Recently, there has been a growing interest in clean hydrogen energy that does not emit carbon dioxide during combustion due to the increasing focus on carbon neutral. Research related to hydrogen production continues, and in this study, we applied waste-derived synthesis gas to the water-gas shift reaction to simultaneously treat waste and produce high-purity hydrogen. To enhance catalytic activity in the high-temperature water-gas shift (HT-WGS) reaction, magnesium was used as a support material alongside cerium. Cu-CeO₂-MgO catalysts were synthesized, with copper acting as the active component for the HT-WGS reaction. A study on the catalytic activity based on the preparation method was conducted, and the Cu-CeO₂-MgO catalyst prepared by impregnation method exhibited the highest activity in the HT-WGS reaction. The observed superior performance of the Cu-CeO₂-MgO catalyst prepared through the impregnation method can be attributed to its significantly higher oxygen storage capacity and amount of active Cu species.

• Applied Chemistry for Engineering
• /
• v.20 no.3
• /
• pp.329-334
• /
• 2009

Yttrium ions doped $TiO_2$ particles have been prepared using a low temperature combustion method. The physical properties were investigated, together with the activity of $TiO_2$ particles as a photocatalyst for the decomposition of methylene blue. From XRD results, the major phase of all the $TiO_2$ particles prepared under basic condition was an anatase structure but a rutile peak was observed when they are prepared under acidic condition. The crystallite size of $TiO_2$ particles was decreased as the molar ratio of CA/TTIP increased. The photocatalytic activity increased with an increase of CA/TTIP molar ratio and pH in the solution. In addition, the doping of 1.0 mole% yttrium ion on the $TiO_2$ enhanced the photocatalytic activity and showed the higher activity than commercial P-25 catalyst.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.115.2-115.2
• /
• 2010

Autothermal reforming(ATR) processes of hydrocarbon liquids such as diesel fuels are spotlighted as methods to produce hydrogen for Fuel cell. However, the use of heavy hydrocarbons as feedstocks for hydrogen production causes some problems which increase the catalyst deactivation by the carbon deposition. Coking can be inhibited by increasing the water dissociation on the catalyst surface. This results in catastrophic failure of whole system. Performance degradation of diesel autothermal reforming leads to increase of undesirable hydrocarbons at reformed gases and subsequently decrease the performance. In this study, perovskite-based catalysts were investigated as alternatives to substitute the noble metal catalyst for the ATR of diesel. The investigated perovskite structure was based on LaCrO3. and metals were added at the A-site to enhance oxygen ion mobility, transition metals were doped on the B-site to enhance the reformation. Substituted Lanthanum chromium perovskite were made by aqueous combustion synthesis, which can produce high surface area. And for the homogeneous fuel supply, we made ultrasonic injection system for reforming. We compared durability of evaporation system and ultrasonic system for fuel injection.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.7 s.250
• /
• pp.692-699
• /
• 2006

In this work, $TiO_2$ nanoparticles were synthesized using $N_2-diluted$ and Oxygen-enriched co-flow hydrogen diffusion flames. The effect of flame temperature on the crystalline structure of the formed $TiO_2$ nanoparticles was investigated. The measured maximum centerline temperature of the flame ranged from 2,103k for oxygen-enriched flame to 1,339K for $N_2-diluted$ flame. The visible flame length and the height of the main reaction zone were characterized by direct photographs. The crystalline structures of $TiO_2$ nanoparticles were analyzed by XRD. From the XRD analysis, it was evident that the crystalline structures of the formed nanoparticles were divided into two sorts. In the higher temperature region, over the 1,700K, the fraction of formed $TiO_2$ nanoparticles having anatase-phase crystalline structure increased with increasing the flame temperature. On the contrary, in the lower temperature region, below the 1,600K, the fraction of anatase-phase nanoparticles increased with decreasing the flame temperature.

• Journal of the Korean Society of Safety
• /
• v.19 no.2
• /
• pp.47-53
• /
• 2004

Emulsion polymerization ws carried out using Alkyl methacrylate(RMA) like MMA, EMA, BMA and Styrene Monomer(SM) for core-shell latex preparation. It was synthesized at $80^{\circ}C$ in the presence of anionic surfactant SLS(Sodium Lauryl Sulfate). FT-IR and DSC analysis are used to confirm the synthesized core-shell emulsion latexes. Moreover DSC and TGA were used to investigate the thermal characterisitcs of them. The differences of the decomposition rate and the activation energy from TGA and DSC analysis are not so big. It considers that the pendent group is not affect of the thermal characteristics and stability on core-shell latexes, which is synthesized with RMA and Styrene. For investigating combustion products, LC50 values were calculated by FED(Fractional Effective Dose)from the Pyrolyzer-Mass sepctrometer.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.2
• /
• pp.66-68
• /
• 2014

Most commercial white LED lamps use blue chip coated with yellow emitting phosphor. The use of blue excitable red and green phosphors is expected to improve the CRI. Several phosphors, such as $SrGa_2S_4:Eu^{2+}$ and $(Sr,Ba)SiO_4:Eu^{2+}$, have been suggested in the past as green components. However, there are issues of the sensitivity and stability of such phosphors. Here, we describe gallium substituted $YAG:Ce^{3+}$ phosphor, as a green emitter. YAG structures are already accepted by the industry, for their stability and efficiency. LEDs with improved CRI could be fabricated by choosing $Y_3Al_4GaO_{12}:Ce^{3+}$ (green and yellow), and $SrS:Eu^{2+}$ (red) phosphors, along with blue chip. Also, the effect of a slight change in chip wavelength is studied, for two phosphor-coated w-LEDs. The reduction in particle size of the coated phosphors also gives improved w-LED characteristics.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.4
• /
• pp.169-172
• /
• 2005

[ $Y_2O_3:Eu$ ] powder was synthesized using a solution-combustion method by dissolving $(CH_3CO_2)_3Y$ and $(CH_3CO_2)_3$ Eu in methyl-alcohol solution. Results from X-ray diffractometery (XRD), thermogravimetry (TG)-differential thermal analysis (DTA) show that $Y_2O_3:Eu$ crystallizes completely when the dry powder is sintered at $500^{\circ}C$. The investigated optical properties were the photoluminescence emission spectra, the excitation spectra and luminescence decay curve. Europium (Eu) concentration had no observable effect on the optical spectrum which depended on the emission intensity. The mean lifetime of synthesized phosphors was $2.3\~2.6 ms$.

• Journal of the Korean Ceramic Society
• /
• v.45 no.7
• /
• pp.418-422
• /
• 2008

The preparation of FeB by SHS in $B_2O_3-Mg-Fe-Fe_3O_4$ system was investigated in this study. In the preparation of FeB, the effects of the initial pressure of inert gas in reactor, the content of Mg and $Fe_3O_4$ in mixture on the reactivity and reaction products was investigated. The minimum initial pressure of inert gas in reactor for SHS reaction in this system was 25 atm, and as the pressure increased, the concentration of unreacted Mg decreased and combustion temperature increased. At the initial inert gas pressure in reactor of 25 atm, the optimum composition for the preparation of pure FeB was $1.5B_2O_3$+3.43Mg+ 1.7Fe+$0.1Fe_3O_4$. The FeB synthesized in this condition had an irregular shape and the particle size of $5\;{\mu}m$.

• Journal of Hydrogen and New Energy
• /
• v.26 no.4
• /
• pp.308-317
• /
• 2015

To investigate the effect of microstructure on the formation of the desorption peak, the volumetric thermal analysis technique (VTA) was applied to the Mg-13.5 wt% Ni hydride system. The sample made by the HCS (hydriding combustion synthesis) process had two kinds of Mg microstructures. Linear heating was started with various constant heating rates. Only one peak was appeared in the case of the small initial hydrogen wt% (0.83 wt%). Yet, two peaks were appeared with increasing initial hydrogen wt% (1.85 and 3.73 wt%) when only Mg was hydrogenated. The first peak was formed through the evolution of hydrogen from $MgH_2$, made by eutectic Mg. The second peak was formed through the evolution of hydrogen from $MgH_2$, made by primary Mg. Therefore, this result shows that the microstructure also has a considerable effect on forming the desorption peak. We have also derived the hydrogen desorption equations by VTA to get apparent activation energy when the rate-controlling step for the desorption of the hydrided system is the diffusion of hydrogen through the ${\alpha}$ phase and the chemical reaction ${\beta}{\rightarrow}{\alpha}$.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.551-559
• /
• 1998

장경비가 큰 탄화규소를 탄소와 규소간의 고온연소반응으로 제조하기 위하여 공정변수에 따른 연소거동과 미세조직의 변화를 조사하였다. 연소합성된 생성물은 주로 $\beta$-SiC이며 연소반응이 충분히 진행되지 못하였을 경우에는 미량의 잔류 반응물과 $\alpha$-SiC가 관찰되었다. 생성된 탄화규소의 평균입도는 약 5$\mu\textrm{m}$로 작았으며, $1300^{\circ}C$ 이상의 예열 조건에서 장경비가 30이상인 탄화규소를 합성할 수 있었다. 압분 강도가 69MPa인 분말의 성형체에서 평균 연소 온도와 평균 전파 속도는 각각 약 $1425^{\circ}C$와 2.1mm/sec 범위이며, 연소 온도는 흑연 분말을 사용하였을 경우가 탄소 섬유를 사용한 경우보다 약 $10^{\circ}C$ 높았다. 연소 반응을 임의로 중단시킨 시편의 계면을 EDX와 Auger 전자 현미경으로 분석한 결과 상호 확산층이 관찰되지 않았다. 이는 탄화규조의 연소합성이 용해-석출 모델에 의하여 진행됨을 시사한다. 예열 온도에 따른 연소 반응 중의 온도 분포를 유한 요소법으로 해석함으로써 $2500^{\circ}C$의 초기 연소 개시 온도에 대하여 예열 온도 $300^{\circ}C$에서는 연소파가 거의 전파할 수 없으며 예열 온도가 $1300^{\circ}C$에서는 시료 내부에 자체 전파가 가능한 $2000^{\circ}C$이상의 온도 구역이 존재함을 알았다.