• 열처리공학회지
• /
• 제27권2호
• /
• pp.59-64
• /
• 2014

Cu-Al-Mn shape memory alloys of a variety of composition were characterized in terms of shape memory properties and cold workability. Cold workability tested by cold rolling indicated that the alloys solution treated in the ${\alpha}+{\beta}$ region have a higher ductility than those solution treated in the ${\beta}$ region. Also it is known that cold workability increased with the decrease in Al content in the ${\beta}$ region. This seems to be resulted from the fact that Mn addition causes to expand ${\beta}$ region toward lower Al content and lower order-disorder transition temperature, consequently, ${\beta}$ of excellent workability being frozen even at room temperature. Experimental results regarding shape memory showed that the properties were better with a higher Al contents at a given Mn content, which is closely related with martensitic transformation. It is also shown that super elasticity limit was enhanced with decrease in the yield strength of alloys because a lower yield strength seems to initiates slip at the lower applied stress.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.74-79
• /
• 2003

When workability at the a certain bulk deformation process is defined as the maximum plastic deformation capability that the workpiece can sustain without causing any cracks or fracture, the workability is dependent on the microstructure, initial workpiece shape, stress state developed during the deformation process, strain rata and presence of the interfacial friction between workpiece and tool. For a review purpose, the workability definition and test methods are summarized depending on the applied stress state at bulk deformation process in Table 1 at the text. In this study, the cold workabilities of as-cast A16061 bulk material have been measured and comparatively analyzed at the primary tensile stress state by using tensile specimens, the primary compressive stress state by using cylindrical specimens, and the forming limit diagram by ductile fracture.

• 한국재료학회지
• /
• 제26권11호
• /
• pp.628-634
• /
• 2016

The cold rolling workability and mechanical properties of two new alloys, designed and cast Al-5.5Mg-2.9Si and Al-7Mg-0.9Zn alloys, were investigated in detail. The two alloy sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1 mm by multi-pass rolling at ambient temperature. The rolling workability was better for the Al-7Mg-0.9Zn alloy than for the Al-5.5Mg-2.9Si alloy; in case of the former alloy, edge cracks began to occur at 50% rolling reduction, and their number and length increased with rolling reduction; however, in the latter alloy, the sheets did not have any cracks even at higher rolling reduction. The mechanical properties of tensile strength and elongation were also better in the Al-7Mg-0.9Zn alloy than in Al-5.5Mg-2.9Si alloy. Work hardening ability after cold rolling was also higher in the Al-7Mg-0.9Zn alloy than in the Al-5.5Mg-2.9Si alloy. At the same time, the texture development was very similar for both alloys; typical rolling texture developed in both alloys. These differences in the two alloys can primarily be explained by the existence of precipitates of $Mg_2Si$. It is concluded that the Al-7Mg-0.9Zn alloy is better than the Al-5.5Mg-2.9Si alloy in terms of mechanical properties.

• 한국건설순환자원학회논문집
• /
• 제2권1호
• /
• pp.40-45
• /
• 2014

본 연구에서는 한중 콘크리트 타설시 발생되는 초기동해로 인한 피해를 방지하고 조강성을 향상시키기 위하여 기존 연구에서 이용된 정제(Tablet)화된 급결제를 사용 하였다. 특히 국내에서는 한중 콘크리트라고 해도 적은양의 플라이애시가 치환되고 있으므로 이러한 Tablet을 플라이애시 치환 콘크리트에 혼입하여 workability, early strength 및 동결융해 저항성을 비교 확인하였다. 그 결과 Tablet 0.5%, 1.0%가 가장 좋은 결과를 나타내어 일정시간 동안 작업시간 확보가 가능하며 초기동해 및 조기강도 특성을 증진 시킬 뿐만 아니라 높은 동결융해 저항성 및 내구성 지수를 가지고 있어 한중 콘크리트로의 적용이 가능하다는 것을 확인하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2010년도 춘계 학술논문 발표대회 1부
• /
• pp.21-23
• /
• 2010

This study was conducted to draw various decisive elements of a reasonable heat curing method and to examine the importance in deciding a construction method when constructing cold weather concrete. As a result, the items proposed as important elements at the time of decision of a heat curing method included economy, workability, maintainability, insulation capability, reduced construction period and usability. As a result of importance by items under AHP technique, it was found the most important element was insulation capability, followed by reduced construction period and workability. As a result of comparison of a heat supplying and a heat insulation method by dual bubble sheet differed 2 times as much as a heat supplying method, especially the evaluation degree by insulation capability and reduced construction period was high.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.99-101
• /
• 2008

At 21st century, material development concepts were changed to fulfill the environmental friendly demands. This study is to study the effect of pressurized nitrogen gas and manganese in high nitrogen austenitic stainless steel(HNS) in which N and Mn elements substitute the nickel element. 100kg HNS ingots were made by Pressurized Vacuum Induction Melting(P-VIM) and were forged according to free forging process. As forged HNS were hot and cold rolled by pilot scale rolling machine. Depending on the rolling condition, the mechanical properties of HNS were changed. The roll thrust and sheet folding showed asymmetry condition between work and drive side during cold and hot rolling. The purpose of this study are to improve workability the hot and cold rolling machine and to set the conditions for establishing the rolling process.

• 열처리공학회지
• /
• 제27권1호
• /
• pp.15-22
• /
• 2014

This study is to investigate the phase changes and cold workability after isothermal transformation at $780^{\circ}C$ by using the high temperature gas nitrided (HTGN) STS 430 ferritic stainless steel specimens. The phase diagram of STS 430 steel obtained by calculation showed that the phase appeared at $1100^{\circ}C$ showed as ${\alpha}+{\gamma}{\rightarrow}{\gamma}{\rightarrow}{\gamma}+Cr_2N{\rightarrow}{\gamma}+Cr_2N+CrN$ with increasing nitrogen concentration. Also, the transformation of ${\gamma}{\rightarrow}Cr_2N$ during heat treatment isothermally at $780^{\circ}C$, nitrogen pearlite with lamellar type was fully formed at the nitrogen permated surface layer for 10 hrs. However, this transformation was not completed for 1 hr, resulting nitrogen pearlite plus martensite. The cold rolled specimen of isothermally transformed at $780^{\circ}C$ for 10 hrs after high temperature gas nitriding decreased the layer thickness of nitrogen pearlite inducing the deformation of hard $Cr_2N$ phase. the dissolution rate of $Cr_2N$ phase increased rapidly with increasing cold rolling ratio. Specimens with the microstructure of nitrogen pearlite (isothermally transformed at $780^{\circ}C$ for 10 hrs) were possible to cold rolling without crack formation. However, the mixed structures of nitrogen pearlite + martensite (isothermally transformed at $780^{\circ}C$ for 1 hr) were impossible to cold deformation without cracking.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.953-958
• /
• 2001

The concrete which has placed under cold weather has some defects such as the decrease of initial strength by hydration delay, strength unrecover at unhardened concrete freezing and structural failure and crack by expansion pressure. So, in this study, we tried to develope the concrete which can be made under cold weather without defect by using of do-icing agency In concrete test, the used do-icing agency has the characteristics of de-icing and rapid hydration. By test results, Co{$NH_{2}$$]_{2}$is unsuitable for workability, and NaN$O_{2}$ is the most suitable agency for cold weather. And for curing, the cured concrete at $21^{\circ}C$ for 24 hours has the safe strength.

• 한국도로학회논문집
• /
• 제20권1호
• /
• pp.47-58
• /
• 2018

PURPOSES : The purpose of this study is to evaluate the mechanical properties of a cold-recycling asphalt mixture used as a base layer and to determine the optimum emulsified-asphalt content for ensuring the mixture's performance. METHODS : The physical properties (storage stability, mixability, and workability) of three types of asphalt emulsion (CMS-1h, CSS-1h, and CSS-1hp) were evaluated using the rotational viscosity test. Asphalt emulsion residues, prepared according to the ASTM D 7497-09 standard, were evaluated for their rheological properties, including the $G*/sin{\delta}$and the dynamic shear modulus (${\mid}G*{\mid}$). In addition, the Marshall stability, indirect tensile strength, and tensile-strength ratio (TSR) were evaluated for the cold-recycling asphalt mixtures fabricated according to the type and contents of the emulsified asphalt. RESULTS : The CSS-1hp was found to be superior to the other two types in terms of storage stability, mixability, and workability, and its $G*/sin{\delta}$ value at high temperatures was higher than that of the other two types. From the dynamic shear modulus test, the CSS-1hp was also found to be superior to the other two types, with respect to low-temperature cracking and rutting resistance. The mixture test indicated that the indirect tensile strength and TSR increased with the increasing emulsified-asphalt content. However, the mixtures with one-percent emulsified-asphalt content did not meet the national specification in terms of the aggregate coverage (over 50%) and the indirect tensile strength (more than 0.4 MPa). CONCLUSIONS : The emulsified-asphalt performance varied greatly, depending on the type of base material and modifying additives; therefore, it is considered that this will have a great effect on the performance of the cold-recycling asphalt pavement. As the emulsified-asphalt content increased, the strength change was significant. Therefore, it is desirable to apply the strength properties as a factor for determining the optimum emulsified-asphalt content in the mix design. The 1% emulsified-asphalt content did not satisfy the strength and aggregate coverage criteria suggested by national standards. Therefore, the minimum emulsified-asphalt content should be specified to secure the performance.

• 오토저널
• /
• 제16권1호
• /
• pp.31-41
• /
• 1994

1. 가공성 평가실험 및 평가기술. 1.1 가공성 평가시험법. 1.2 실험방법. 1.3 피단한계. 1.4 파단발생 평가이론. 1.5 파단평가이론의 적용. Bulk재 소성가공 공정중에 있어서 거시적 가공성평가 방법 및 응용방법에 대하여 논하였다. Bolt Heading 가공과 같은 냉간압조 가공에 있어서 상기 모델들에 의한 재료고유의 가공한계선과 변형경로를 비교하므로써 가공성을 평가할 수 있으며 또한 보다 복잡한 형상제품의 최적가공을 위한 가공조건 및 재질선정의 최적화에도 유용하게 이용될 수 있다.