• Journal of the korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.31-40
• /
• 1983

A study was made of the effect of cold working and stabilizing temperature on the fatigue properties of Aluminum alloy 5083. The amount of cold working ranged from 14% to 35% and stabilizing temperature was 120.deg. C-160.deg. C. Rotary bending fatigue test was carried out, and it was found that 1) E specimen that had been cold worked by the cold reduction of 35% and stabilized at 160.deg. C for 2 hours was showed the most excellent fatigue limit and endurance ratio and, 2) By the results of the between crack propagation behavior and stress intensity factor, E specimen was showed the better resistance to fatigue crack growth than others.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1227-1234
• /
• 1994

A cold spot temperature control system for the batch annealing furnace has been established in order to reduce energy consumption which is essential to improve productivity and stabilize the properties of products. A relationship between annealing cycle time and gas flow rate is developed and also for the variation of coil cold spot temperature with time during heating, and actual temperature measurements at mid-width of each coil during soaking. The results of the temperature variation effect on the cold rolled steel sheet batch annealing are as follows. (1) Cooling rate increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component change. (2) In case of short time heating, the slowest heating part is the center of B coil and in case of ling time heating, the low temperature point moves from the center of coil to inside coil. (3) The outside of top coil is the highest temperature point under heating, which becomes the lowest temperature point under cooling. (4) Soaking time determination depends on the input coil width, and soaking time for quality homogenization of 1214 mm width coil must be 2 hours longer than that of 914 mm width coil.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.71-72
• /
• 2013

This study investigates the effect of the diameters of reinforcement bars located in an euro-form before placing concrete in a cold weather condition. The diameters of reinforcement bars with 13 mm, 19 mm, 25 mm and 32 mm were prepared for the experimental tests. Results showed that the larger the size of the diameter of the bars, the higher were the temperature drop. However, this study found that its effect on the temperature drop of the bars was insignificant.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.793-797
• /
• 2000

The environmental problems by using coolant demanded the new cooling methods. As one of them the studies on the dry grinding with compressed cold air have been done. The cooling method using compressed cold air was effdve thmugh going down the temperature of compressed air supplied below $-25^{\circ}C$ and inneasing the amount of mmpresd cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using MQL(Minimum Quantity Lubrication) or mist newly were suggested. These two methods can satisfy both cooling effect and lubrication with only small amount of coolant, also has the benefit in the point of decreasing the envimnmental pollution. This paper focused on analyzing the grindmg characteristics of the cooling method using mid. The generated heat and grinding force of the cooling method using mist were compared with them of coolant and compressed cold air. And them grinding test according to the temperature of compressed cold air, mist spray amount and mist supply direction were done.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.12
• /
• pp.2031-2038
• /
• 2020

Objective: This study aimed to determine the effect of intermittent feeding and cold water on performance and carcass traits in broiler chickens between 4 to 6 wk of age exposed to daily high temperature. Methods: Broilers were assigned to four treatment groups according to a 2×2 factorial design between 22 to 42 d of age (80 broilers per treatment, 4 replications). Broilers were divided into two main groups as feeding type (ad-libitum [AL] and intermittent [IF] for 6 h daily) and sub-groups as water temperature (normal [NW], 24.9℃ and cold [CW], 16.4℃). Heat treatment was applied between 11.00 to 17.00 h daily between 22 to 42 d of age. Results: Live weight at 6th wk was not affected by feeding type and water temperature, but the live weight was significantly higher in IF chickens at the 5th wk (p<0.05). Average weekly gain of IF broiler chickens were higher compared to AL group at 4, 5, and 6 wk of age (p< 0.05). Although feeding type did not affect feed intake in 4 and 5th wk, feed intake was higher in IF chickens at 6th wk (p<0.01). In addition, feeding type and water temperature did not affect feed conversion ratio and interactions were not significant (p>0.05). Water temperature had no significant effect on heart, liver, gizzard, and abdominal fat percentages (p>0.05). Conclusion: It is concluded that IF increased the average weekly gain in chickens reared under daily heat stress for 6 h between 22 to 42 d of age. IF in hot environmental conditions slightly increased performance without adversely affecting health, welfare, and physiological traits, whereas CW implementation had no significant effect on performance. It can also be said that IF suppresses a sudden increase in body temperature depending on age and live weight.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.22-30
• /
• 2003

Engine-out HC emissions were investigated during cold and hot start. The tests were conducted according to engine cooling temperatures which were controlled by simulated coolant temperatures of cold and hot start, on a 1.5L, 4-cylinder, 16 valve, multipoint-port-fuel-injection gasoline engine. Real time engine-out HC emissions were measured at a exhaust port and cylinder head using Fast Response Flame Ionization Detector(FRFID). Unburned hydrocarbons emitted at the cold coolant temperature were much higher than those of the hot coolant temperatures. And the main source of the high HC emission was confirmed as misfire at cold coolant temperature. In addition, the effect of intake valve timing on engine-out HC emissions was investigated. The results obtained indicate that optimized intake phasing provides the potential for start-up engine-out HC emissions reduction.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.1
• /
• pp.49-58
• /
• 2017

Due to low annual average temperature, road tunnel lining in domestic cold region (Gangwon province) experiences durability problems. The financial and human damage due to cracks, breakout, exfoliation and water leakage increases every year. However, domestic research on effect of temperature on road tunnel lining damage is insufficient. Thus, this research has investigated 70 tunnels located in cold region (Gangwon-do) to analyze damage status. Furthermore, by contrasting damage on tunnels in relatively warm Gangneung area with those in relatively cold Hongcheon area, the effect of temperature on road tunnel lining damage was analyzed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.203-206
• /
• 2008

Transformation of austenite to martensite during cold rolling has been widely used to strengthen metastable austenitic stainless steel grades. Aging treatment of cold worked metastable austenitic stainless steels, including ${\alpha}'$-martensite phase, results in the further increase of strength, when aging is performed in $200^{\circ}C$ to $450^{\circ}C$ temperature range. The purpose of the present study was to evaluate the effect of time and temperature on the stress-strain behavior of cold worked austenitic stainless steels. The amount of ${\alpha}'$-martensite during cold working and aging was examined by ferrite scope and X-ray diffraction (XRD). During aging at $450^{\circ}C$ for 1hr, tensile strength dramatically increased by 150MPa. Deformed metastable austenitic steels containing the "body-centered" ${\alpha}'$-martensite are strengthened by the diffusion of interstitial solute atoms during aging at low temperature.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.28 no.2
• /
• pp.58-65
• /
• 2014

Bumblebees are important pollinators of crops and wildflowers. Bumblebees generally produce one generation per year. One of the key stages for year-round rearing of bumblebees is breaking diapause. To evaluate the effects of a combination method of $CO_2$-narcosis and cold treatment to break the diapause of B. ignitus and B. terrestris queens, we determined whether this method affected their ability to establish a colony after the diapause break. The diapause treatment regimes that were utilized were $CO_2$ ($CO_2$-narcosis), CT-1M (cold treatment at $5^{\circ}C$ for 1 mo), CT-1M-$CO_2$ ($CO_2$-narcosis after cold treatment for 1 mo), CT-2M-$CO_2$ ($CO_2$-narcosis after cold treatment for 2 mo), CT-2M (cold treatment for 2 mo), CT-2.5M-$CO_2$ ($CO_2$-narcosis after cold treatment for 2.5 mo) and CT-2.5M (cold treatment at $5^{\circ}C$ for 2.5 mo). In view of the effects on the colony developmental characteristics of B. ignitus queens, the most favorable diapause treatment was CT-1M-$CO_2$. A combination method of $CO_2$-narcosis and cold temperature treatment yielded better results than that of single $CO_2$-narcosis or cold temperature treatment on the colony development of diapause-broken B. ignitus queens. In the case of B. terrestris queens, we concluded that a combination method of $CO_2$ and cold temperature treatment yielded better results than that of a single cold-temperature (up to 2 mo) treatment. In conclusion, the findings of the present study indicated that the combined application of $CO_2$ and cold temperature was a favorable method for the colony development of diapause-broken B. ignitus and B. terrestris queens compared with only $CO_2$-narcosis or cold temperature treatments. A combination method of $CO_2$ and cold treatment reduced the side effect of $CO_2$-narcosis and shortened the duration of cold treatment by at least 1 mo.

• Horticultural Science & Technology
• /
• v.34 no.4
• /
• pp.557-563
• /
• 2016

To improve the germination of Spiraea fritschiana seeds for mass propagation, we evaluated the effect of a range of temperatures, cold stratification periods, and gibberellic acid ($GA_3$) treatments on three germination characteristics. Final germination percentage (FGP) increased as the temperature for seed germination increased, up to $30^{\circ}C$, while the mean germination time (MGT) and the mean number of days to 30% germination ($T_{30}$) decreased when seeds were germinated at $25-30^{\circ}C$. The optimum germination temperature of S. fritschiana seeds is approximately $30^{\circ}C$ considering FGP, MGT, and $T_{30}$ together. FGP increased with the duration of cold stratification up to a period of 6 weeks, but declined after 8 weeks of cold stratification, as prolonged cold stratification can induce dormancy with a resultant decline in germination. Pretreatment with 6-8 weeks of cold stratification or soaking seeds in distilled water or $500mg{\cdot}L^{-1}$ $GA_3$ for 24 h accelerated and increased the germination of S. fritschiana seeds, regardless of temperature. However, further study might be required to evaluate the effect of $GA_3$ concentrations lower than $500mg{\cdot}L^{-1}$ on the promotion of germination in S. fritschiana seeds.