• Structural Engineering and Mechanics
• /
• 제63권1호
• /
• pp.1-9
• /
• 2017

Shot peening is a cold surface treatment employed to induce residual stress field in a metallic component beneficial for increasing its fatigue strength. The experimental investigation of parameters involved in shot peening process is very complex as well as costly. The most attractive alternative is the explicit dynamics finite element (FE) analysis capable of determining the shot peening process parameters subject to the selection of a proper material's constitutive model and numerical technique. In this study, Ansys / LS-Dyna software was used to simulate the impact of steel shots of various sizes on an aluminium alloy plate described with strain rate dependent elasto-plastic material model. The impacts were carried out at various incident velocities. The influence of shot velocity and size on the plastic deformation, compressive residual stress and force-time response were investigated. The results exhibited that increasing the shot velocity and size resulted in an increase in plastic deformation of the aluminium target. However, a little effect of the shot velocity and size was observed on the magnitude of target's subsurface compressive residual stress. The obtained results were close to the published ones, and the numerical models demonstrated the capability of the method to capture the pattern of residual stress and plastic deformation observed experimentally in aluminium alloys. The study can be quite helpful in determining and selecting the optimal shot peening parameters to achieve specific level of plastic deformation and compressive residual stress in the aluminium alloy parts especially compressor blades.

• 셀메드
• /
• 제3권4호
• /
• pp.32.1-32.6
• /
• 2013

Plectranthus amboinicus Benth (Lamiaceae) is a medicinal plant native to India, and its leaves are widely used in several traditional medicinal preparations. The purpose of this study was to detect and quantify phenolics present in ethyl acetate and acetone extracts of P. amboinicus leaves, and evaluate their antioxidant, antibacterial, antimutagenic and anticancer activities. The HPLC chromatograms of crude leaf extracts indicated the presence of phenolics like caffeic acid, coumaric acid, rutin, quercetin and gallic acid, which were present in the range of 0.01 - 1.41 mg/g in ethyl acetate and 0.03 - 1.93 mg/g in the acetone extract. The acetone extract showed statistically (p < 0.05) higher antioxidant activity ($IC_{50}$, 99.59 ${\mu}g/ml$) than ethyl acetate extract ($IC_{50}$, 149.96 ${\mu}g/ml$). Statistically (p < 0.05) higher antimutagenicity was shown by acetone extract (46.16%) as compare to ethyl acetate extract (12.16%) at 500 ${\mu}g/plate$ concentration. The acetone extract showed higher antibacterial activity than ethyl acetate extract, and both the extracts showed highest activity against B. cereus (375 and 625 ${\mu}g/ml$, respectively) and lowest activity against Y. enterocolitica (1000 and 1125 ${\mu}g/ml$, respectively). Both the extracts also showed inhibitory effect on cancer cell lines HCT-15 and MCF-7. These results suggest that the leaves of P. amboinicus possess various biological activities, and validate the traditional use of the leaves of P. amboinicus against cold, infection and ulceration.

• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.80-84
• /
• 2011

The weight reduction of the transportations has become an important technical subject Al and Al alloys, especially Al 5052 alloys have been being applied as door materials for automobile. One of the most widely known car weight-reduction methods is to use light and corrosion-resistant aluminum alloys. However, because of high electrical and thermal conductivity and a low melting point, it is difficult to obtain good weld quality when working with the aluminum alloys. Also, Pulse MIG welding is the typical aluminum welding process, but it is difficult to apply to the thin plate, because of melt-through and humping-bead. In order to enhance weld quality, welding parameters should be considered in optimizing the welding process. In this experiment, Al 5052 sheets were used as specimens, and these materials were welded by adopting new Cold Metal Transfer (CMT) pulse process. The proper welding conditions such as welding current, welding speed, torch angle $50^{\circ}$ and gap 0~1mm are determined by tensile test and bead shape. Through this study, range of welding current are confirmed from 100A to 120A. And, the range of welding speed is confirmed from 1.2m/min to 1.5m/min.

• 한국강구조학회 논문집
• /
• 제27권2호
• /
• pp.231-241
• /
• 2015

직접강도법은 NAS(2004)와 AS/NZS 4600(2005)에 의해서 냉간성형강재의 설계에 처음 채택되었다. 이 설계법은 용접형강 부재에도 효과적으로 적용이 가능하다고 판단된다. 본 논문에서는 최근 수행된 용접형강 부재의 직접강도법 개발에 대해서 살펴보고자 한다. 용접형강 압축 및 휨부재의 설계강도식은 H, C, RHS, CHS 형강, 플레이트거더 및 보강판 단면의 실험 결과에 근거하여 개발 되었다. 직접강도법과 현행 설계기준에 의해 예측된 강도의 비교 결과를 통하여 직접강도법을 적용하여 좌굴혼합이 발생하는 용접형강 기둥 및 보 부재의 압축, 휨 및 전단강도를 합리적으로 산정할 수 있는 것을 입증하였다.

• 한국표면공학회지
• /
• 제47권4호
• /
• pp.186-191
• /
• 2014

Double layer films which consisted of aluminum(Al) and magnesium(Mg) have been prepared by e-beam deposition. The structure, alloy phase, and corrosion resistance of the prepared films were investigated before and after heat treatment. The first (bottom) layer fixed with Al, and the thickness ratio between Al and Mg layers has been changed from 1 : 1 to 5 : 1, respectively. Total thickness of Al-Mg film was fixed at $3{\mu}m$. The cold-rolled steel sheet was used as a substrate. Heat treatment was fulfilled in an nitrogen atmosphere at the temperature of $400^{\circ}C$ for 2, 3 and 10 min. Surface morphology of as-deposited Al-Mg film having Mg top layer showed plate-like structure. The morphology was not changed even after heat treatment. However, cross-sectional morphology of Al-Mg films was drastically changed after heat treatment, especially for the samples heat treated for 10 min. The morphology of as-deposited films showed columnar structure, while featureless structure of the films appeared after heat treatment. The x-ray diffraction data for as-deposited Al-Mg films showed only pure Al and Mg peaks. However, Al-Mg alloy peaks such as $Al_3Mg_2$ and $Al_{12}Mg_{17}$ appeared after heat treatment of the films. It is believed that the formation of Al-Mg alloy phase affected the structure change of Al-Mg film. It was found that the corrosion resistance of Al-Mg film was increased after heat treatment.

• 수산해양기술연구
• /
• 제21권2호
• /
• pp.151-156
• /
• 1985

본 연구에서는 양쪽크랙 인장시험편을 이용한 평면응력 파괴인성치 J 하(1C)를 검토하기 위하여, 두께 4.5mm 일반구조용 압연강판(SS41)을 균질화 및 연화처리하고 각각의 경우에 대하여 크랙비가 0.55, 0.65, 0.75인 시험편을 준비하여 J 하(1C) 및 저항곡선의 거동을 고찰하였다. 얻어진 결과를 요약하면 다음과 같다. 1) 양쪽 크랙 인장시험편을 사용하여 J 하(1C)를 구한 값은 한계하중에 의한 방법이 Rice가 제안한 방법보다 크게 나타남을 알 수 있다. 2) Rice가 제안한 방법으로 J 하(1C)는 실험한 크랙비 범위 0.55-0.75에서 거의 일정한 값을 나타내고 저항곡선의 기울기는 크랙비에 따라 증가하였다. 3) Rice가 제안한 방법으로 [SS41의 J 하(1C)의 평균값은 모재는 22.8kgf/mm, 균질화 처리재는 24.7kgf/mm, 연화처리재는 26.9kgf/mm를 얻었다

• 한국분말재료학회지
• /
• 제18권5호
• /
• pp.430-436
• /
• 2011

Joining of NiO-YSZ to 316 stainless steel was carried out with B-Ni2 brazing alloy (3 wt% Fe, 4.5 wt% Si, 3.2 wt% B, 7 wt% Cr, Ni-balance, m.p. 971-$999^{\circ}C$) to seal the NiO-YSZ anode/316 stainless steel interconnect structure in a SOFC. In the present research, interfacial (chemical) reactions during brazing at the NiO-YSZ/316 stainless steel interconnect were enhanced by the two processing methods, a) addition of an electroless nickel plate to NiO-YSZ as a coating or b) deposition of titanium layer onto NiO-YSZ by magnetron plasma sputtering method, with process variables and procedures optimized during the pre-processing. Brazing was performed in a cold-wall vacuum furnace at $1080^{\circ}C$. Post-brazing interfacial morphologies between NiO-YSZ and 316 stainless steel were examined by SEM and EDS methods. The results indicate that B-Ni2 brazing filler alloy was fused fully during brazing and continuous interfacial layer formation depended on the method of pre-coating NiO-YSZ. The inter-diffusion of elements was promoted by titanium-deposition: the diffusion reaction thickness of the interfacial area was reduced to less than 5 ${\mu}m$ compared to 100 ${\mu}m$ for electroless nickel-deposited NiO-YSZ cermet.

• Journal of Welding and Joining
• /
• 제34권6호
• /
• pp.42-46
• /
• 2016

Hydrogen assisted cracking (HAC) is one of the most complicated problem in welding. Huge amount of studies have been done for decades. Based on them, various standards have been established to avoid HAC. But it is still a chronic problem in industrial field. It is well known that the main causes of the hydrogen crack are residual stress, crack susceptible micro structures and a certain critical level of hydrogen concentration. Even though the exact generating mechanism is unclear till today, it has been reported that the hydrogen level in the weld metal should be managed less than a certain amount to prevent it. Matsuda studied that the residual hydrogen level in the weld metal can be varied even if the initial hydrogen content is same. It is also insisted in this report that the residual hydrogen concentration is in stronger correlation with hydrogen crack than the initial hydrogen content. But, in practical point of view, the residual hydrogen is still hard to consider because measuring hydrogen level is time and cost consuming process. In this regard, numerical analysis is the only solution for considering the residual hydrogen content. Meanwhile, Takahashi showed the possibility of predicting the residual hydrogen by a rigorous FE analysis. But, few commercial software suitable for solving the weld metal hydrogen has been reported yet. In this study, two dimensional thermal - hydrogen coupled analysis was developed by using the commercial FE software MARC. Since the governing equation of the hydrogen diffusion is similar to the heat transfer, it is shown that the heat transfer FE analysis in association with hydrogen diffusion property can be used for hydrogen diffusion analysis. A series of simulation was performed to verify the accuracy of the model. For BOP (Bead-On-Plate) and the multi-pass butt welding simulations, remaining hydrogen contents in the weld metal is well matched with measurements which are referred from Kim and Masamitsu.

• 한국식품조리과학회지
• /
• 제12권2호
• /
• pp.129-137
• /
• 1996

The purpose of this study was that to estimate the microbial and sensory quality by the method and time of holding in the step of holding of Cow's Knee Broth, Stir-Fry Pork and Cooked Cuttlefish that were provide at the industry foodservice establishment, then to suggest safer feeding by the reasonable holding method. The results are as follows: Cow's Knee Broth: holding at room temperature was shown that the number of mi- crobiology by passage of the holding time was higer than the case of holding at steam table, but it was lower after reheating it. As a result of sensory test, it was exellent to holding at steam table and to reheat after holding room temperature within four hours and six hours each. Stir-Fry Pork: as a result of microbial analysis, in the case of holding at the steam table microbes increased safer two hours, but after four and six hours they little reduced. In the case of holding at room temperature the number of microbes increased according to the passage of time. As a result of sensory analysis, its taste of room temperature holding was fine until four and six hours each. Cooked Cuttlefish: as a microbial analysis, it was shown that the amount of total plate counts of room temperature holding ten times as high as the latter after six hours. As the result of sensory analysis, the cold holding was better until six hours and the room temperature holding was fine just until two hours. As a result of food poisoning bacteria, it was negative in every test in sample against Salmonella, Staphylococcus aureus, Vibrio parahaemolyticus.

• Steel and Composite Structures
• /
• 제13권6호
• /
• pp.571-586
• /
• 2012

The paper addresses some key issues related to the design of composite slabs with cold-formed profiled steel sheets. An experimental programme is first presented, involving six composite slab specimens tested with a view to evaluating Eurocode 4 (EC4) provisions on testing of composite slabs. In four specimens, the EC4-prescribed 5000 load cycles were applied using different load ranges resulting from alternative interpretations of the reference load $W_t$. Although the rationale of the application of cyclic loading is to induce loss of chemical bond between the concrete plate and the steel sheet, no such loss was noted in the tests for either interpretation of the range of load cycles. Using the recorded response of the specimens the values of factors m and k (related to interface shear transfer in the composite slab) were determined for the specific steel sheet used in the tests, on the basis of three alternative interpretations of the related EC4 provisions. The test results confirmed the need for a more unambiguous description of the m-k test and its interpretation in a future edition of the Code, as well as for an increase in the load amplitude range to be used in the cyclic loading tests, to make sure that the intended loss of bond between the concrete slab and the steel sheet is actually reached. The study also included the development of a special-purpose software that facilitates design of composite slabs; a parametric investigation of the importance of m-k values in slab design is presented in the last part of the paper.