• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.5
• /
• pp.398-408
• /
• 2007

For better evaluation of material thickness by using the reflection type pulsed eddy current method, various probe models are designed and their response signals, characteristics, and sensitivities to thickness variation are investigated by a numerical analysis method. Since the sensor needs to detect magnetic fields from eddy currents induced in a test material, not from the exciter coil, two types of models that are shielded by the combination of copper and ferrite and only by ferrite are considered. By studying response signals from these shielded probe models, the peak value and the zero crossing time are selected as useful signal features for the evaluation of material thickness. Investigation of sensitivities of these two features shows that the sensitivity of peak value is more useful than that of zero crossing time and that the probe shielded only by ferrite gives much better sensitivity to thickness variation.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.6
• /
• pp.529-536
• /
• 2015

A defect could be generated in bolts for a use of oil filters for the manufacturing process and then may affect to the safety and quality in bolts. Also, fine defects may be imbedded in oil filter system. So it is very important that such defects be investigated and screened during the multiple manufacturing processes. Therefore, in order effectively to evaluate the fine defects, the FEM simulations were performed to make characterization in the crack detection of the bolts and the parameters such as number of turns of the coil, the coil size, applied frequency were calculated based on the simulation results. Simulations were carried out for the defect signal of eddy current probe. Exciter and receiver were utilized. In this paper, the FEM simulations were performed in both bobbin-type and pancake-type probe, both probes were optimized under Eddy current FEM simulations and the results of calculation were discussed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.125-130
• /
• 2013

According to the law revision of TPMS mounting obligations in Korea, researches about energy harvester which is the alternative of the battery are actively performed by many groups. Because WSN (Wireless Sensor Network) has the proposition of "Install and forget" and the power supplier also has the same performance as the vehicle's lifetime. In this paper, electromagnetic induction type of energy harvester through the relative motion between the rotating wheel and the fixed brake disc is introduced by using the most efficient source as the rotating motion in the view of vehicle's mechanism. The coil on the wheel and the permanent magnet at the brake disc are arranged in several ways. These various arrangements are the number of coil turns are consisted of design variables. By using the orthogonal array to reduce the experimental cost, the optimal composition is verified through the experiment. Finally the validity of the module is considered by measuring the level of storable electrical energy.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.41-44
• /
• 2003

We propose portable equipment that monitors current and voltage of high-potential power transmission lines. In the equipment, a current and voltage sensor are attached to an insulator that supports a power transmission line: A clamped to the power line and the detected current signal is transmitted to the ground station by a wireless optical link using transmission line is detected by a high resistance element, zinc oxide (ZnO). That acts as a potential divider between the power line and ground. We make an experimental device for 66kV power line and demonstrate that it can monitor currents proposed equipment is small-sized, light, and inexpensive in comparison with the conventional CT (current transformer) and PT (potential transformer) since it does not require high potential insulators and magnetic cores, further, the equipment is easily installed owing to its small size and its simple structure.

• Journal of Sensor Science and Technology
• /
• v.3 no.1
• /
• pp.32-39
• /
• 1994

Catalytic combustion type sensor was fabricated for alcohol detection, and its characteristics were tested. When the resistance of Pt coil for pellistor is 2.0 ohm, suggestible input power to bridge circuit was about 300 mW for methanol detection, and in the range from 350 mW to 400 mW for ethanol. Pellistors were prepared by means of impregnating Pt or Pd on the ${\gamma}$-alumina bead for sensing element, and transition metals such as $Co_{3}O_{4}$, $Fe_{2}O_{3}$ for compensating element.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.584-586
• /
• 2004

This paper deals with the development of on-line fault and lightning stroke section locating system for branched overhead transmission line. The section locating algorithm of this system i3 by analyzing the distribution pattern of current flowing through the overhead ground wire. It composes of three parts; current sensors, local remote terminal unit(RTU) and analysis program at surveillance tenter. Double Rogowski coil sensor having integrating amplifier was designed as current sensor. In order for current pattern analysis, the transmitted waves from each sensor wert synchronized by GPS tim c clock in RTU. While, lightning stroke location are judged only by polarity information of lightning currents. This design has a benefit in simplicity of signal processing unit of RTU.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.12
• /
• pp.1197-1202
• /
• 2009

We present a power-efficient driving scheme that consists of piezoelectric actuator and driver IC for AF (Auto-Focus) on ISM (Image Sensor Module). The piezoelectric actuator is more power-efficient than conventional voice coil motor actuator. And high power-efficiency driver IC is designed. So the proposed driving scheme using designed piezoelectric actuator and driver IC is more close to recent trend of green IT. The diver IC should guarantee fast and accurate performance. So, the optimum driving method and high accurate frequency synthesizer are proposed. The die area of designed driver IC is $2.0{\times}1.6mm^2$ and power consumption is 2.8mW.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.2
• /
• pp.199-206
• /
• 2015

Regular high-strength carbon steel is currently the most commonly used pipe material for onshore and offshore pipelines. The corrosion of offshore pipelines is a major problem as they age. The collapse of these structures as a result of corrosion may have a heavy cost is lives and assets. Therefore, their monitoring and screening is a high priority for maintenance, which may ensure the integrity and safety of a structure. Monitoring risers and subsea pipelines effectively can be accomplished using eddy current inspection to detect the average remaining wall thickness of corroded low-alloy carbon steel pipelines through corrosion scaling, paint, coating, and concrete. A test specimen for simulating the offshore pipeline is prepared as a standard specimen for an analysis and experiment with differential bobbin eddy current sensors. Using encircling coils, the signals for the defect in the simulated specimen are analyzed and evaluated in experiments. Differential bobbin eddy current sensors can diagnose the defects in a specimen, and experiments have been carried out using the developed bobbin eddy current sensor. As a result, the most optimum coil parameters were selected for designing differential bobbin eddy current sensors.

• Journal of the Korean Magnetics Society
• /
• v.19 no.1
• /
• pp.17-21
• /
• 2009

In this study, we have investigated that the excitation current and operation frequency dependences of the output properties of the orthogonal fluxgate sensor which was fabricated with a Co base amorphous wire and a pick-up coil. The output signal increased linearly with increase of the excitation current below 0.3 A, and decreased with increase of the excitation current over 0.6 A. It was also found that the output increased sensitively with increase of operation frequency below 1.3MHz. The output was 3.8 V at the frequency of 1.3MHz while 1.32 V at 1MHz.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.3
• /
• pp.26-30
• /
• 2009

Korea Superconducting Tokamak Advanced Research(KSTAR) device is composed of 30 superconducting magnets, magnet structure, vacuum vessel, cryostat, current feeder system, and etc. KSTAR device is operated in the cryogenic temperature and high magnetic field. We install about 800 sensors - temperature sensors, stain gages, displacement gages, hall sensors - to monitor the thermal, mechanical, electrical status of KSTAR during operation. As a tremendous numbers of sensors should be installed for monitoring the KSTAR device, the method of effective installation was developed. The sensor test was successfully carried out to check its reliability and its reproduction in the cryogenic temperature. The sensor signal is processed by PXI-based DAQ system and communicated with central control system via machine network and is shown by Operator Interface(OPI) display in the main control room. In order to safely operate the device, any violations of mechanical & superconductive characteristic of the device components were informed to its operation system & operator. If the monitored values exceed the pre-set values, the protective action should be taken against the possible damage. In this paper, the system composition, operation criteria, operation result were presented.