• Journal of the Korean Wood Science and Technology
• /
• v.43 no.3
• /
• pp.327-333
• /
• 2015

To measure the dimensional stability of three softwoods by vacuum pressurization of water soluble melamine-formaldehyde (MF) resin impregnation process, properties of resin treated compressed woods (compregs) were measured after impregnating the water soluble MF resin into three coniferous wood species for different impregnation times and resin concentrations. As the resin concentration was higher and impregnation time was longer, coefficients of volumetric shrinkage and anti-volumetric swelling efficiency increased, but coefficients of volumetric swelling, anti-volumetric swelling efficiency and absorption decreased. Also, weight percent gain increased remarkably as the resin concentration was high, but there was no uniform relationship with impregnation time.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.1
• /
• pp.66-71
• /
• 1994

To increase drying rate and reduce drying degradation, pretreatments such as prefreezing and presteaming have been widely used in wood industries. Presteaming lumbers prior to kiln drying is known positively to improve its permeability, to increase diffusion coefficient and to reduce discoloration, but negatively to increase collapse. Prefreezing lumbers prior to kiln drying is also known to reduce significantly its drying defects and its shrinkages. Thus it is no doubt that the pretreated lumbers shrink diversely from the untreated. In this study the shrinkage behaviors of the pretreated specimens are investigated by drying two tropical hardwoods (Apitong and Taun) in three different dying conditions: high temperature and slow drying rate (drying in a closed cylinder), high temperature and rapid drying rate (drying in an oven) and low temperature and slow drying rate(drying at room temperature). The prefrozen specimens show the least volumetric shrinkages in most drying conditions. The specimens dried in cylinders shrink most among all drying conditions. In general the pretreated specimens reached the 30 % moisture content faster than the untreated by about 30 %.

• Journal of the Korean Ceramic Society
• /
• v.45 no.12
• /
• pp.796-801
• /
• 2008

$LaGaO_3$ thin film was prepared on Ni-Fe metal porous substrate by Pulsed Laser Deposition method. By the thermal reduction, the dense $NiO-{Fe_3}{O_4}$ substrate is changed to a porous Ni-Fe metal substrate. The volumetric shrinkage and porosity of the substrate are controlled by the reduction temperature. It was found that a thermal expansion property of the Ni-Fe porous metal substrate is almost the same with that of $LaGaO_3$ based oxide. $LaGaO_3$ based electrolyte films are prepared by the pulsed laser deposition (PLD) method. The film composition is sensitively affected by the deposition temperature. The obtained film is amorphous state after deposition. After post annealing at 1073K in air, the single phase of $LaGaO_3$ perovskite was obtained. Since the thermal expansion coefficient of the film is almost the same with that of LSGM film, the obtained metal support LSGM film cell shows the high tolerance against a thermal shock and after 6 min startup from room temperature, the cell shows the almost theoretical open circuit potential.

• Journal of Korean Society of Forest Science
• /
• v.71 no.1
• /
• pp.14-21
• /
• 1985

This study was carried out in order to prevent the devaluation of wood itself and wood products causing by anisotropy, hygroscopicity, shrinkage and swelling - properties that wood itself only have, in order to improve utility of wood, by emphasizing the natural beautiful figures of wood, to develop the dimensional stabilization techniques of wood with PEG that it is a cheap, non-toxic and the impregnation treatment is not difficult, on the effects of PEG molecular weights (200, 400, 600, 1000, 1500, 2000, 4000, 6000) and species (Pinus densiflora S. et Z., Larix leptolepis Gordon., Cryptomeria japonica D. Don., Cornus controversa Hemsl., Quercus variabilis Blume., Prunus sargentii Rehder.). The results were as follows; 1) PEG loading showed the maximum value (137.22%, Pinus densiflora, in PEG 400), the others showed that relatively slow decrease. The lower specific gravity, the more polymer loading. 2) Bulking coefficient didn't particularly show the correlation with specific gravity, for the most part, indicated the maximum values in PEG 600, except that the bulking coefficient of Quercus variabilis distributed between the range of 12-18% in PEG 400-2000. In general, the bulking coefficient of hardwood was higher than that of softwood. 3) Although there was more or less an exception according to species, volumetric swelling reduction was the greatest in PEG 400. That is, its value of Cryptomeria japonica was the greatest value with 95.0%, the others indicated more than 80% except for Prunus sargentii, while volumetric swelling reduction was decreased less than 70% as the molecular weight increase more than 1000. 4) The relative effectiveness of hardwood with high specific gravity was outstandingly higher than softwood. In general, the relative effectiveness of low molecular weight PEG was superior to those of high molecular weight PEG except that Quercus variabilis showed more than 1.6 to the total molecular weight range, while it was no significant difference as the molecular weight increase more than 4000. 5) According to the analysis of the results mentioned above, the dimensional stabilization of hardwood was more effective than softwood. Although volumetric swelling reduction was the greatest at a molecular weight of 400. In the view of polymer loading, bulking coefficiency reduction of swelling and relative effectiveness, it is desirable to use the mixture of PEG of molecular weight in the range of 200-1500. To practical use, it is recommended to study about the effects on the mixed ratio on the bulking coefficient, reduction of swelling and relative effectiveness.