• Nuclear Engineering and Technology
• /
• v.56 no.2
• /
• pp.463-471
• /
• 2024

Average and local convective heat transfer coefficients of nitrogen are measured experimentally in an electrically heated circular tube for a range of Reynolds number from 1.08 × 10⁴ to 3.60 × 10⁴, and wall-to-bulk temperature ratio from 1.01 to 1.77. The exit Mach number is up to 0.17, and the heat flux is up to 46 kW·m^-2. The molybdenum test section has a 62 diameters heated section with an inside diameter of 5 mm and a 30 diameters entrance section to ensure the fully-developed flow. Uncertainty of Nusselt number is less than 1.6 % in this study. The results indicate that the average heat transfer correlations evaluated by both the bulk and the modified film Reynolds numbers agree well with the experimental data. The local heat transfer results based on bulk properties are compared with previous empirical correlations. New prediction correlations are recommended which are significantly affected by the property variation and heated length. The comparison between the proposed correlations and experimental points shows that 88 % of experimental data fall into an error of 10 %, and almost all data are within an error of 20 %.

• Computers and Concrete
• /
• v.34 no.4
• /
• pp.409-425
• /
• 2024

This paper utilizes LS-DYNA software to numerically investigate impact response and damage evaluation of fiber-reinforced polymer (FRP) bars-reinforced ultra-high-performance concrete (UHPC) composite beams (FRP-UHPC beams). Three-dimensional finite element (FE) models are established and calibrated by using literature-based static and impact tests, demonstrating high accuracy in simulating FRP-UHPC beams under impact loading. Parametric analyses explore the effects of impact mass, impactor height, FRP bar type and diameter, and clear span length on dynamic response and damage modes. Two failure modes emerge: tensile failure with bottom longitudinal reinforcement fracture and compression failure with local concrete compression near the impact region. Impact mass or height variation under the same impact energy significantly affects the first peak impact force, but minimally influences peak midspan displacement with a difference of no more than 5% and damage patterns. Increasing static flexural load-carrying capacity enhances FRP-UHPC beam impact resistance, reducing displacement deformation by up to 30%. Despite similar static load-carrying capacities, different FRP bars result in varied impact resistance. The paper proposes a damage assessment index based on impact energy, static load-carrying capacity, and clear span length, correlating well with beam end rotation. Their linearly-fitting coefficient was 1.285, 1.512, and 1.709 for the cases with CFRP, GFRP, and BFRP bars, respectively. This index establishes a foundation for an impact-resistant design method, including a simplified formula for peak midspan displacement assessment.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.230-238
• /
• 2011

The experimental study for the performances of 100 kW marine current turbines (Horizontal Axis Turbine) has been conducted with three cases of 700 mm diameter model in PNU 100 m towing tank. Three cases of impeller have been designed according to the variation of section configuration and tip shape. The model tests have been carried out at different speed of revolution to find out the scale effect (Reynolds number effect). The designed rake impeller was the best among them in the efficiency point of view especially at high Tip Speed Ratio (TSR). The present study is expected to be extended to conduct at high reynolds number as well as the computational study for the validation.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.139-145
• /
• 2010

An integrity testing for stone columns was attempted using crosshole S-wave logging. The method is conceptionally quite similar to the crosshole sonic logging (CSL) for drilled piers. The critical difference in the logging is the use of S-wave rather than P-wave, which is used in CSL, because swave is the only wave sensing the stiffness of slower unbounded materials than water. An electro-mechanical source, which can generate reversed Swave signals, was utilized in the logging. The stone column was delineated using the S-wave travel times across the stone column, the S-wave velocity profile of the crushed stone($V_{cs}$-profile) and that of surrounding soil($V_s$-profile). In the calculation of $V_{cs}$-profile of the crushed stone, its friction angle and Ko (coefficient of lateral earth pressure at rest) are recommended to be used. The calculation of the column diameter is not much affected by the values of friction angle and Ko.

• The Korean Journal of Pain
• /
• v.36 no.2
• /
• pp.208-215
• /
• 2023

Background: To evaluate the feasibility, inter-reader reliability, and intra-reader reliability for various morphological features reported to be related to iliotibial band friction syndrome (ITBFS) on knee magnetic resonance imaging (MRI). Methods: A total of 145 patients with a clinical diagnosis and knee MRI findings consistent with ITBFS were included in the "study group" and 232 patients without knee pathology on both physical examination and MRI were included in the "control group". Various morphologic features on knee MRI were assessed including the patella shape, patella height, lateral epicondyle anterior-posterior (AP) width, lateral epicondyle height, ITB diameter (ITB-d), and ITB area (ITB-a). Results: Patients in the study group had significantly higher lateral epicondyle height (13.9 mm vs. 12.92 mm, P = 0.003), ITB-d (2.9 mm vs. 2.0 mm, P = 0.022), and ITB-a (38.5 mm² vs. 23.8 mm², P < 0.001) than the control group. ITB-a showed higher area under the curve index (0.849 with 74.1% sensitivity and 72.4% specificity at a 30.3 mm² cutoff) than ITB-d (0.710 with 70.8% sensitivity and 61.2% specificity at 2.4 mm cutoff) and lateral epicondyle height (0.776 with 72.4% sensitivity and 67.8% specificity at 13.4 mm cutoff). However, only the inter-reader agreement for ITB-a (intraclass correlation coefficient = 0.65) was moderate, while the agreements for other morphologic features were good or excellent. Conclusions: Lateral epicondyle height seems to be a reliable and feasible morphologic feature for diagnosis of ITBFS.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.17 no.1
• /
• pp.58-68
• /
• 2015

This study compares the wind stability of Larix kaempferi (Lamb.) Carr., Pinus koraiensis Sie. & Zucc. and Abies holophylla Maxim. to understand and inform wind risk management of these plantation trees at Daegwallyeong, Korea. Temporary square plots of $20m{\times}20m$ ($400m^2$) were laid out, and DBH (Diameter at Breast Height) and height for trees greater than 10 cm in DBH were measured by species. A total of 15 plots with 5 plots each in L. kaempferi, P. koraiensis and A. holophylla stands were sampled at random. Among the species, A. holophylla and P. koraiensis have comparatively lower h/d (Height/DBH) ratios than L. kaempferi. These results indicate that the former two species are more wind firm than the latter species. About 9% of the L. kaempferi trees have higher h/d ratios than the critical threshold limit 80. These trees are vulnerable to wind damage and should be removed in the next thinning regime. The analysis of variance detected a significant difference (p < 0.05) in the h/d ratios and Gini coefficient indicating species differences and DBH size variation, respectively. Gini coefficient was 16.4% in A. holophylla, 15.9% in P. koraiensis and 14% in L. kaempferi stands indicating limited DBH size variation. Lower h/d ratios are attributed to thinning in these stands and tree morphological differences. To increase wind firmness, low thinning should concentrate to remove trees with the h/d ratio above 80 coinciding at the time of stand distinction phase. Forest managers and practitioners should measure and maintain h/d ratios of trees below the critical threshold limit of 80 through stand density management. Variable density thinning approach should be tested to increase tree DBH sizes of the even-aged stands.

• Journal of Korean Society of Forest Science
• /
• v.108 no.4
• /
• pp.592-599
• /
• 2019

This study aimed to develop an equation for estimating stem volume for Larix kaempferiin South Korea using independent variables, diameter at breast height (DBH), and height as being closely associated with stem volume. Analysis was conducted on the growth performance of 2,840 Larix kaempferi samples across South Korea after felling them and gleaning diameter data according to both stem height and stem analyses. In order to test the fitness of six different stem taper equations, empirical assessment was conducted for fitness index (FI), bias, mean, and absolute deviation (MAD), and coefficient variation (%CV). The two selectedmodels found to be optimal were the following: model one (V=a+bDBH²), established by employing DBH only; and model four (V=a+bDBH²H), established by utilizing DBH and height, respectively. The findings of non-linear regression indicated statistical significance (p < 0.05) in a and b, which were the coefficients for the intercepts and slopes of the models. The FI of the models ranged between 94% and 99%, and the bias was close to zero, while MAD ranged from 0.01 to 0.05, and %CV from 5.97 to 14.43, indicating a high level of fitness. Thus, using the suggested models, the basic information necessary for forest management was obtained, and an estimation of the stem volume was effected without delay soon after effecting DBH and height measurements.

• Journal of Korean Society of Forest Science
• /
• v.38 no.1
• /
• pp.33-45
• /
• 1978

The purpose of present study is to analyze the genetic variation of natural stand of Pinus densiflora. In 1975 following after the selection of 1974, twenty trees from each of three natural populations of the species were selected and their open-pollinated seeds were collected, and the locations and conditions of the populations ate presented in table 1, 2 and figure 1. Some morphological traits of the populations were already detailed in our second report of this series, in which Myong-Ju and Ul-Jin populations were regarded to be superior phenotypically to suweon population. The morphological traits of cone, seed and seed-wing, and also the growth performances and needle characters of the seedling were observed in the present study according to the previous methods. The results obtained are summarized as follows; 1. The meteorological data obtained by averaging the records of 30 year period (1931~1960) measured from the nearest meteorological stations to each population are shown in fig.2, 3, 4. The distributional patterns of investigated climate factors are generally considered to be similar among the locations. However, the precipitation density during growing season and the air temperature during dormant season on Suweon area, population 6, were quite different from those of the other areas. 2. The measurements of fresh cone weight, length, diameter and cone index, i.e., length to diameter ratio are presented in table 7. As shown in table 7, all these traits except for cone diameter seem to be highly significant in population differences and family differences within population. 3. The morphological traits of seed and seed-wing are detailed in table 8, 9, and highly significant differences are recognized among the populations and the families within population in seed-wing length, seed-wing index, seed weight, seed-length and seed index but not among the populations in the other observed traits. The values of correlation coefficient between the characters of cone and seed are given in table 10 and the positive significant correlations can be observed in the most parts of the compared traits. 4. Significant statistical differences among populations and families within population are observed in the growth performances of 1-0 and 1-1 seedling height of these progenies. But the differences in root collar diameter are shown only among families within population. As shown in table 13, the most parts of correlations are not significant statistically between the growth performances of seedling and the seed characters. 5. The number of stomata row on both sides of needle and the serration density were measured in the seedlings from each of the families of the three populations. As shown in table 15, statistical differences are considered to be significant among the populations and among the families within population in serration density but not among the populations in stomata row on both sides of the needle. The results differ from those of the third report of this series. Even if one of the reason seems to be the diversity of selected populations, it could not be confirmed definitely. The correlations between progenies and parents are not generally observed in the investigated traits of needle as shown in table 16.

• Korean Journal of Medicinal Crop Science
• /
• v.5 no.4
• /
• pp.266-275
• /
• 1997

Anemarrhena asphodeloides BUNGE is one of important medicinal crops, which has been collected or/and cultivated for its rhizomes. The main medicinal ingredient of the A. asphodeloides Bunge rhizomes is a saponin, which is known to have medical values for diaphoresis, sedatives and biuresis. However, studies on cultural methods and breeding works on this plant have not been made in detail. To increase productivity and to improve quality of crops, it is important to collect cultivated and wild lines, to classify them based on morphological and genetic characteristics, and to select superior pure lines at first. Therefore, total 20 A. asphodeloides lines collected were cultivated at the fieldof Chungnam Provincial Administration of Rural Development in 1995 to study the agronomic characteristics and to classify them based on morphological characteristics. Characteristics related with reproductive organ such as the number of spikes per plant and peduncle length showed greater variations than vegetative organrelated characteristics such as leaf length and rhizome length based on the coefficient of variation. Vigorous shoot growth resulted in better development of reproductive organs such as peduncle length and number of spikes per plant. However, the development of spikes was negatively correlated with chlorophyll content. Characteristics of underground parts were more significantly correlated with spike characteristics than aerial part characteristics. A. asphodeloides tested in this study were classified into 2 groups (group A and group B) based on centroid linkage cluster analysis. Group A showed more vigorous shoot growth with more leaves and spikes per plant, longer peduncle length, thicker peduncle diameter and higher shoot dry weight than group B. Group A could be further classified into 2 sub-groups based on leaf size, spike length and peduncle diameter, while group B also could be classified based on number of leaves, number of spikes and shoot dry weight.

• Journal of Bio-Environment Control
• /
• v.22 no.3
• /
• pp.284-290
• /
• 2013

This study analyzed the geometric, compressive, cutting and friction properties of oriental melons in order to design a gripper capable of soft handling and a cutter for cutting oriental melon vine among the end effector of oriental melon as a preliminary step for developing the end effector of the robot capable of harvesting oriental melons in protected cultivation. As a result, the average length, diameter at the midpoint, weight, volume and roundness of the oriental melons were 108 mm, 70 mm, 188 g, 333 mL and 3.8 mm. Nonlinear regression analysis was performed on the equation $W=L^a{\times}D_2^b$ with variation of the length (L) and diameter (D2) of the weight (W) of the oriental melons. As a result, it was shown that there was a correlation between a of 2.0279 and b of -0.9998 as a constant value. The average diameter of the oriental melon vine was 3.8 mm, and most vines were distributed within a radius of 5 mm from the center. The average yield value, compressive strength and hardness of the oriental melons were $36.5N/cm^2$, $185.7N/cm^2$ and $636.7N/cm^2$, respectively. The average cutting force and shear strength of the oriental melon vines were $2.87{\times}10^{-2}\;N$ and $5.60N/cm^2$, respectively. The maximum friction coefficient of the oriental melons was rubber of 0.609, followed by aluminium of 0.393, stainless steel of 0.177 and teflon of 0.079. It was considered possible to apply it to the size of the gripper and cutter, turning radius, dynamics of drive motor and selection of materials and their quality in light of the position error and safety factor according to the movement when designing end effector based on the analyzed data.