• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.33-35
• /
• 2003

There are three types that geometrical arrangement of the pulse tube and regenerator - in line type, U type, and coaxial type. The most compact and convenient one practical applications is the coaxial type. It can replace Stirling cryocooler without any change to the Dewar or the connection to the cooled devices. To investigate effects of the inertance tube, we perform experiments with varying inertance tube inner diameter and length. The experimental results show that optimum inertance tube inner diameter and length are 1.3mm, 1900mm respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.2
• /
• pp.11-15
• /
• 2002

High speed probe for measurement of sin91e flux quantum circuits is comprised of coaxial cables and microstrip lines in order to carry high speed signals without loss. For the impedance matching between coaxial cable and microstrip line, we have determined the dimension of the microstrip line with 50${\Omega}$ impedance by simulation and then have investigated the effect of line width and cross-sectional shape of signal line, dielectric material, thickness of soldering lead at the coaxial-to-microstrip transition Point, and the an91c between dielectric material and end part of the signal line on the characteristics of signal transmission of the microstrip line. From the simulation, we have found that these all parameter's had influenced on the characteristic of signal transmission on the microstrip line and should be reflected in fabricating high speed probe, We have also determined the dimension of coplanar waveguide to fabricate testing sample for performance test of high speed probe.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.3
• /
• pp.622-628
• /
• 1996

This paper describes a new serial interface system which uses conventional 75 ohm coaxial cable. Typically parallel 25 pin cable and connectors are used to transfer and receive the data between digital systems such as HDVCR, D3 VTR and HDTV Receiver. The coaxial cable is more desirable for consumer product applications and also for studio applications where long signal paths and switching are required. This serial data transfer technique is thoroughly tested and utilied in the data transmission/reception between systems more than 200 feet apart. It is also cost effective because it does not require RF PLL, SCRAMBLING, and NRZI hardware.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.649-656
• /
• 2000

In this paper, a closed exact from and its approximation of the characteristic impedance of a lossy coaxial line with a thick outer conductor are proposed. It is also shown for 3.5mm reference air line that the proposed approximation is accurate over the entire operating frequency range of the line.

• Journal of the Optical Society of Korea
• /
• v.19 no.6
• /
• pp.614-618
• /
• 2015

This paper described an off-axis head-mounted display system. It is composed of a 7-piece coaxial relay lens group and a freeform surface combiner. This configuration has a simple structure and a wide field of view (FOV). In this design, a freeform surface is chosen as the combiner, to simplify the structure and attain good image quality. We generated this freeform surface by considering both coordinates and normals of discrete data points. Moreover, we realize a coaxial structure in the relay lens group, which is compact and benefits from a loose tolerance requirement. The HMD system we finally realized has a 40° × 30° FOV and 15-mm exit pupil diameter.

• Journal of Industrial Technology
• /
• v.27 no.A
• /
• pp.169-175
• /
• 2007

In High-Speed DSP systems, crosstalk between transmission lines of multi-channel can degrade the performance of equipment operations. This paper presents a microwave board to measure multi-channel coaxial cable assembly. The designed board has good performances from DC to 3 GHz, which have improved characteristic impedance, reduced crosstalk by using via fence, and low transmission loss. Using the designed board, we can measure characteristics of DUT(Device Under Test) such as return loss, insertion loss, crosstalk phase delay, and characteristic impedance. The measured results are used to improve performances of a produced coaxial cable assembly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.15-18
• /
• 2003

The present study addresses an experimental investigations of the near field flow structures of supersonic, dual, coaxial, swirl jet. The swirl stream is discharged from the secondary annular nozzle and the primary inner nozzle provides the sonic and supersonic free jets. The interactions between the secondary swirl and inner soni $c^ersonic jets are quantified by a fine pilot impact and static pressure measurements and are visualized by using a shadowgraph optical method. The pressure ratios of the secondary swirl and primary soni $c^ersonic jets are varied below 7.0. Experiments are conducted to investigate the effects of the secondary swirl stream on the primary sonic and supersonic jets, compared with the secondary stream of no swirl. The results show that the presence of annular swirl stream causes the Mach disk to move more downstream, with the increased diameter, and remarkably reduces the fluctuations of the impact pressures in the supersonic dual coaxial jet, compared with the case of the secondary annular stream of no swirl.swirl.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.24-27
• /
• 2003

Radiofrequency ablation (RFA) as one of the microwave hyperthermia is becoming the treatment of choice for small but inoperable tumors of the liver. In this paper, we designed the applicator composed of semi-rigid coaxial cable antenna with a ring slot for RFA. To optimize the maximum output of radiation with omni direction at 2450 ㎒, we simulated the applicator using Electromagnetic simulation program and analyzed the return loss and the electric field E$\_$tot/ at the near-field region between the simulation results and measurement results. As a result, we obtained the return loss of -29.786 dB at 2450 ㎒ when the applicator was placed between two blocks of a pig's liver, and the measurement results agreed with the simulation results well. Therefore, this applicator using semi-rigid coaxial cable antenna with a ring slot can be used very usefully as the applicator for RFA.

• Journal of the Korean Institute of Navigation
• /
• v.16 no.4
• /
• pp.25-34
• /
• 1992

As a method of measure the absorbing characteristics of microwave absorber, the various microwave measuring method can be used fundamentally. There is, however, a big problem in measuring errors, since the wavelength of microwave such as used for radar is very short. Therefore, this research aimed to design and fabricate a converting adaptor of $20mm^{\phi}$ coaxial tube from a Type-N connector to $20mm^{\phi}$ coaxial tube and to use it for evaluating absorption characteristics of microwave absorber. Furthermore, the measurements of absorbing characteristics and material constants have been performed and review, which were carried out by using the coaxial tube and by using rectangular waveguide, respective. As a result, the validity of the proposed measuring method has been confirmed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.481-482
• /
• 2008

We have designed a Marx Generator, named EMD Pulse Generator(EPG), which makes steep front high voltage, 50ns rise time and 200kV high. It was designed as coaxial type and in small size, 70cm high and 20cm in diameter. The firing system is trigatron type and the spark gap switches in each stage are coaxial with the axis of the system. In this paper we mention about the characteristics of EPG and several experimental data.