• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.2
• /
• pp.183-191
• /
• 1990

Polycrystalline CdS film have been prepared by coating a slurry constiting of CdS, CdCl2, various amount of InCl3 and propylene glycol on glass substrate and by sintering in a nitrogen atmosphere, and their sintering behaviors, electrical properties and optical properties have been investigated. As the amount of InCl3 increases, the enhancing effect of CdCl2 on sistering decreses resulting in a sharp decrease in optical transmittance and an increase in electrical resistivity. The carrier concentration is almost independent of InCl3 added due to the occurrence of chlorine doping and to the compensating effect of indium dopant. Microstructure an optical properties of CdS film, which contain CdCl2 and InCl3 before sintering, can be improved by sintering in a sealed boat.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.497-504
• /
• 2009

DLC is considered as the candidate material for application of moving parts in automotive components relatively in high pressure and temperature operating conditions for its high hardness with self lubrication and chemical inertness. Different deposition method such as arc plating, ion gun plating and PECVD were used for comparing mechanical and tribological properties of each DLCs deposited on stainless steel with 1 um thick respectively. Among these 3 types of DLCs, the arc plated DLC film showed highest value for wear resistance in dry condition. From the results of analysis for physical properties of DLC films, it seems that the adhesion force and crack initiation modes were more important factors than intrinsic mechanical properties such as hardness, elastic modulus and/or roughness to the wear resistance of DLC films. Raman spectroscopy was used for understanding chemical bonding natures of each type of DLC films. Typical D and G peaks were identified based on the deposition method. Hardness of the coating layers were identified by nanoindentation method and the adhesions were checked by scratch method.

• Corrosion Science and Technology
• /
• v.15 no.6
• /
• pp.297-302
• /
• 2016

Water-based systems are dominating the coating market because of worldwide VOCs regulations. Research is focusing especially on waterborne polyurethane (WPU) because of its unique mechanical and chemical properties. However, commercial WPU consists of linear thermoplastic polymers with polar groups on the main chain, which do not perform as well as solvent-borne PU in a two-pack system. In this study, APTES were used as a chain crosslink agent to overcome commercial WPU's limited performance. WPUs synthesized by using a sol-gel process were evaluated with FT-IR, particle analysis, TGA, tensile tests, pull-off tests, SEM, and EIS. The results showed that WPUs with added APTES had better thermal stability, mechanical properties, and water resistance than did WPUs without added APTES. Consequently, the sol-gel process increased the crosslink density of WPUs and modified the WPU's own properties.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.149-155
• /
• 2001

New semi-fluorinated polyol esters were synthesized by condensation reaction of polyols (NPG and TMP) and carboxylic acids such as 2-ethylhexanoic acid, stearic acid and perfluorooctanoic acid. The structures of polyol esters were confirmed by FT-IR and H-NMR etc. And, the fluorinated polyol esters were insoluble in several oils, however, the semi-fluorinated polyol esters were soluble in several oils depended on the structure of polyol esters. The physical properties such as 4-ball wear property and extreme-pressure (EP) properties were characterized by measuring wear scar diameter through ASTM D2266 and by determining the load-carrying through ASTM D2783 method, respectively. As the results, wear scar diameters of oils in which the semi-fluorinated polyol esters were added were not changed compared to those of not added oils. While extreme-pressure properties remarkably Increased with fluorine contents of the esters depended on the structure of acid moiety and polyol moiety. Also, the extreme-pressure property of semi-fluorinated NPG polyol ester in gasoline engine oil was better than that of commercial Teflon coating additive.

• Journal of Surface Science and Engineering
• /
• v.33 no.4
• /
• pp.266-272
• /
• 2000

Sputtered $MoS_2$ thin films provide lubrication and wear improvements for vacuum and space applications. In this study, deposition of $MoS_2$ thin films by R.F. magnetron sputtering was studied with regard to the micro-structural change of $MoS_2$ film and mechanical properties. The coating parameters such as the working pressure, the RF power, the substrate temperature, the etching time were varied to determine how these parameters affected the film morphology and mechanical properties of deposited films. The best wear properties and critical load were observed with the film deposited at $70^{\circ}C$, 1.0$\times$$10^{ -3}$ Torr, 170W and 1 hour deposition time. The critical load increased with the increase of sputter etching time.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.7
• /
• pp.715-719
• /
• 1997

In order to study the dielectric properties of the oriental lacquer films, three different films have been prepared differing purification and curing procedures. Dielectric properties were measured in the frequency range of 1 Hz to 105 Hz at various temperatures between - 50 ℃ and 150 ℃. The DEA using 1 Hz showed that glass transition and secondary relaxation temperatures of oriental lacquer film are very time dependent. In addition, the frequency-independent negative peak between 25 ℃ and 45 ℃ was observed, which could represent the formation of crosslink by laccase enzyme during heating. On the contrary, the high temperature cured film showed a hardly noticeable negative peak at the temperature range. The relationship between thermodynamic properties and chemical structures has been discussed based on the analysis of the dielectric relaxation behavior using the Cole-Cole plot and the dielectric relaxation intensity.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.160-161
• /
• 2021

To prepare polyurethane coatings for top coatings of automobiles, acrylic resins containing 75% of solids were synthesized by a radical polymerization. The viscosity of the acrylic resins was increased with increasing OH values. Crosslinked acrylic-urethane clear coatings were obtained by curing reaction between the synthesized acrylic resins and hexamethylene diisocyanate(HDI) trimer(Desmodur N-3600). The physical properties from the following studies were carried out : viscosity(Zahn cup #2), adhesion, pensil hardness, and 60° specular gloss. Various properties of the acrylic-urethane clear coatings as top coatings of mobile coat were evaluated on the coating specimens. Adhesion property to a substrate, 60° specular gloss, and pencil hardness of prepared paint showed quite good properties.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.3
• /
• pp.39-47
• /
• 2000

This study was carried out to investigate the effect of the type of base papers containing Sw-BDP, HW-BDP and Bamboo-BKP on the properties and printabilities of coated papers. Also it was intended to evaluate the effect of coated paper prepared with anionic and amphoteric latex based coating color. The results obtained from this study were as follows. The fiber length of Bamboo-BKP was observed longer than that of the Hw-BKP and shorter than that of the Sw-BKP. This has effect on physical properties. Therfore the results of mea-suring physical properties were higher ratio of Sw-BKP physical properties tended to be slightly higher with the increase I the mixing ratio. Considering the optical properties of base papers the highest opacity was obtained in case of the Hw-BKP and the second appeared Bamboo-BKP. On the other hand smoothness roughness and air permeability of Bamboo-BKP were lower than those of wood pulp and the optical properties of coated papers tended to show the similar with those of base papers. The ink receptivity and print gloss of the coated papers for Bamboo-BKP were lower than those of wood pulp. As the mixing ratio of Sw-BKP was increased the properties and printabilities were improved slightly. Meanwhile amphoteric latex was improved the optical properties and printability of coated papers.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.375-378
• /
• 2007

Abrasive wear between piston ring face and cylinder liner is an extremely unpredictable and hard-to-reproduce phenomenon that significantly decreases engine performance. Wear by abrasion are forms of wear caused by contact between a particle and solid material. Abrasive wear is the loss of material by the passage of hard particles over a surface. From the pin-on-disk test, particle dent test and scuffing test, abrasive wear characteristics of diesel engine cylinder liner-piston ring have been investigated. Pin-on-disk test results indicate that abrasive wear resistance is not simply related to the hardness of materials, but is influenced also by the microstructure, temperature, lubricity and micro- fracture properties. In particle dent test, dent resistance stress decreases with increasing temperature. From the scuffing test by using pin-on-disk tester, scuffing mechanisms for the soft coating and hard coating were proposed and experimentally confirmed.

• Archives of Pharmacal Research
• /
• v.26 no.7
• /
• pp.575-580
• /
• 2003

The present study was designed to develop a microencapsulated L-ascorbic acid and iron that could be used to fortify milk and to determine the sensory properties of milk fortified with microencapuslation. Coating material was medium-chain triacylglycerol (MCT), and selected core material was ferric ammonium sulfate and L-ascorbic acid. The highest efficiency of microencapsulation was 95.0% in the ratio of 15:1 as coating to core material. Ascorbic acid release was increased sharply up to 5 d storage as 6.5%. TBA value was the lowest when both capsulated iron and ascorbic acid were added during 12 d storage, compared with other treatments. In sensory analysis, most aspects were not significantly different between control and capsulated ascorbic acid fortified milk at 5 d storage. The present study indicated that the use of microencapsulated ascorbic acid with MCT is effective for fortifying milk. In addition, these results suggest that acceptable milk products can be prepared with microencapsulated ascorbic acid and iron.