• 한국표면공학회지
• /
• 제30권3호
• /
• pp.167-174
• /
• 1997

WC-C0 base cemented carbides were plasma nitrided to obtain more hadened surface layer. The surface hardness of Hv1338 which is higher than a non-treated ane by 30%, and the hardened layer thickness of about 50$\mu\textrm{m}$ were obtained by the treatment of 3hrs under the conditions of $550^{\circ}C$, and 5torr of gas pressure of which composition was 1:1 of $N_2:H_2$. The nitrided surfaces has WIN and W2N phases in the non-coated samples and AIN phase in the alumina coated sampled as the results of X-ray results, and showed surface roughnness of 5$\mu\textrm{m}$ which were caused by the sputtering action of the plasma gasee. The hardenened layer exihibits an enhanced wear resistance the cuttability test.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 춘계학술대회 논문집
• /
• pp.164-169
• /
• 2000

The remote measurement system(RMS) as a new experimental method is limited in its application to crack measurements at elevated temperatures because of the oxide layer on the specimen surface. Since TiAlN and Cr coating layers have a high resistance to oxidation and wear, this paper proposed a TiAlN and Cr coating technique for specimens to facilitate the measurement of crack growth behavior using RMS. To investigate the effects of the coating layer, tension and fatigue tests were carried out at room temperature and at 538$^{\circ}C$, using specimens of 1Cr-1Mo-0.25V steel. From the experimental results, it was found that the mechanical properties of the TiAlN and Cr coated specimens were similar to those of the substrate. Accordingly, the TiAlN and Cr coated layer had hardly any influence on the fatigue crack propagation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.609-611
• /
• 1995

In this study, we experimented the properties of SOG film as sacrificials layers in surface micromachining and made $SiO_2$ films through spin, bake, cure process. When we culled SOG films once, SOG film thickness is 1000 $\sim$ 3000 ${\AA}$. Then we coaled 200-${\AA}$ SOG film on 9000 ${\AA}$-CVD oxide and then we fabricated test structure, cantilever and ring/beam structure. We estimated deformed structure by SEM. As the results, The deformation of the structure layer in the SOG-coated sacrificial layers is small compared with that or the structure layer on CVD oxide or PSG. In the future, we use multi coated SOG films, SOG film become adequate material as sacrificial layer.

• 한국해양공학회지
• /
• 제16권2호
• /
• pp.60-66
• /
• 2002

The remote measurement system(RMS) as a new experimental method is limited in its application to crack measurement at elevated temperatures because of the oxide layer on the specimen surface. Since TiAIN and Cr coating layers have a high resistance to oxidation and wear, this paper proposed a TiAIN and Cr coating technique for specimens to facilitate the measurement of crack growth behavior using RMS. To investigate the effects of the coating layer, tension and fatigue tests were carried out at room temperature and at $538^{\circ}C$. The test material was 1Cr-1Mo-0.25V steel which is widely used as a turbine rotor material. From the experimental results, it was found that the mechanical properties of the TiAIN and Cr coated specimens were similar to those of the substrate. Accordingly, the TiAIN and Cr coated layer had hardly any influence on the fatigue crack propagation.

• 한국재료학회지
• /
• 제27권7호
• /
• pp.392-397
• /
• 2017

Fluorine-doped tin oxide (FTO) coated NiCrAl alloy foam is fabricated using ultrasonic spray pyrolysis deposition (USPD). To confirm the influence of the FTO layer on the NiCrAl alloy foam, we investigated the structural, chemical, and morphological properties and chemical resistance by using USPD to adjust the FTO coating time (12, 18, and 24 min). As a result, when an FTO layer was coated for 24 min on NiCrAl alloy foam, it was found to have an enhanced chemical resistance compared to those of the other samples. This improvement in the chemical resistance of using USPD NiAlCr alloy foam can be the result of the existence of an FTO layer, which can act as a protection layer between the NiAlCr alloy foam and the electrolyte and also the result of the increased thickness of the FTO layer, which enhances the diffusion length of the metal ion.

• 한국분말재료학회지
• /
• 제13권1호
• /
• pp.18-24
• /
• 2006

The brazing adhesion properties of Ag coated W-Ag electric contact on the Cu substrate have been investigated in therms of microstructure, phase equilibrium and adhesion strength. Precoating of Ag layer ($3{\mu}m$ in thickness) on the $W-40\%Ag$ contact material was done by electro-plating method. Subsequently the brazing treatment was conducted by inserting BCuP-5 filler metal (Ag-Cu-P alloy) layer between Ag coated W-Ag and Cu substrate and annealing at $710^{\circ}C$ in $H_2$ atmosphere. The optimum brazing temperature of $710^{\circ}C$ was semi-empirically calculated on the basis of the Cu atomic diffusion profile in Ag layer of commercial electric contact produced by the same brazing process. As a mechanical test of the electric contact after brazing treatment the adhesion strength between the electric contact and Cu substrate was measured using Instron. The microstructure and phase equilibrium study revealed that the sound interlayer structure was formed by relatively low brazing treatment at $710^{\circ}C$. Thin Ag electro-plated layer precoated on the electric contact ($3{\mu}m$ in thickness) is thought to be enough for high adhesion strength arid sound microstructure in interface layer.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.368-374
• /
• 2007

CVD-SiC coating has been introduced as a protective layer in TRISO nuclear fuel particle of high temperature gas cooled reactor (HTGR) due to its excellent mechanical stability at high temperature. In order to prevent the failure of the TRISO particles, it is important to evaluate the fracture strength of the SiC coating layer. It is needed to develop a new simple characterization technique to evaluate the mechanical properties of the coating layer as a pre-irradiation step. In present work, direct strength measurement method with the specimen of hem i-spherical shell configuration was suggested. The indentation experiment on a hemisphere shell with a plate indenter was conducted. The fracture strength of the coating layer is related with the critical load for radial cracking of the shell. The finite element analysis was used to drive the semi-empirical equation for the strength measurement. The SiC hemispherical shells were successfully recovered from the section-grinding of TRISO coated particle and successive heat treatment in air. The strength of CVD-SiC coating layer was evaluated from the experimentally measured critical load during the indentation on SiC hemisphere shell. Weibull diagram of fracture strength was also constructed. This study suggested a new strength equation and experimental method to measure the fracture strength of CVD-SiC coating of TRISO coated fuel particles.

• 한국결정성장학회지
• /
• 제29권6호
• /
• pp.352-358
• /
• 2019

최근 인쇄용지는 단순히 정보 전달의 기능을 넘어서 미적, 예술적 가치가 부가면서 고품질의 인쇄가 가능한 도공지(coated paper)에 대한 시장의 수요가 증가하고 있다. 특히 실사급 고품질의 인쇄가 가능한 잉크젯 프린팅의 도공지는 잉크의 인쇄적성을 향상시키기 위하여 표면에 젖음성(wettability)과 다공성 구조(porous structure)를 갖는 도공층의 역할이 매우 중요하다. 본 연구에서는 나노 실리카 졸 입자에 실란 커플링제로 표면처리하고 수용성 결합제인 폴리비닐알콜(PVA)와 혼합하여 도공액(coating color)를 제조하고 원지(base paper)에 코팅하여 도공층을 제조하였다. 실란 커플링제로 표면처리한 나노 실리카 도공층은 표면처리하지 않은 도공층과 비교하여 균일한 기공 분포 및 평탄한 표면 거칠기를 가지며, 판매용 고급 인화지와 유사한 광택도를 갖는 것을 확인하였다. 특히 잉크의 망점(dot)에 대한 진원도로 평가하는 인쇄적성 평가 결과 실란 커플링제로 표면처리한 도공지는 다층 구조의 도공층을 갖는 판매용 고급 인화지보다 더 우수한 결과를 얻을 수 있었다. 이러한 결과는 실란 커플링제 표면처리를 통하여 나노 실리카 입자의 분산성이 향상되어 우수한 젖음성과 균일한 기공 분포를 갖는 도공층 형성이 가능하였기 때문으로 확인되었다.

• 한국재료학회지
• /
• 제25권5호
• /
• pp.226-232
• /
• 2015

본 연구에서는 손상된 알루미늄 금형의 복원을 위해 고온플라즈마 용사법을 이용하여 금형의 표면에 $Al/Al_2O_3$ 혼합분말을 용사한 후 코팅층과 모재의 증착강도에 대한 평가를 수행하였다. 증착강도의 평가는 분사노즐의 이동속도, 순수한 알루미늄 bond coat 층의 유무에 따라 평가되었으며, bond coat 층을 생성시키지 않았을 때, 코팅층의 두께는 열팽창에 의한 잔류인장응력의 감소를 위해 두껍지 않아야 하지만 일정두께 이상이 되어야 최대의 증착강도를 얻을 수 있음이 나타났다. 또한 순수한 알루미늄 bond coat 층은 내부 결함이 없는 응고된 금속이기 때문에 두께에 따른 증착강도의 영향을 그대로 받아 두께가 두꺼울수록 bond coat 층을 생성시키지 않은 시험편보다 증착강도가 매우 낮게 측정되었다. 반면, 가장 얇게 bond coating 된 시험편 Bc3(3회의 bond coating층과 분사건의 이동속도가 20 cm/sec인 시험편) 는 bond coating을 하지 않은 시험편 중 가장 높은 증착강도를 가지는 시험편 Wbc20(bond coating층이 없고 분사건의 이동속도가 20 cm/sec인 시험편)보다 약 2배 이상증착강도가 향상되었다. 따라서 금형의 복원시에 중간층의 형성이 반드시 필요하며, 이는 코팅층의 잔류 인장응력을 보완시키며 고인성의 순수한 알루미늄과 같은 코팅층과 유사한 층을 코팅하는 것이 필요한 것으로 사료된다.

• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.580-584
• /
• 2007

The ZrC layer instead of SiC layer is a critical and essential layer in TRISO coated fuel particles since it is a protective layer against diffusion of fission products and provides mechanical strength for the fuel particle. In this study, we carried out computational simulation before actual experiment. With these simulation results, Zirconium carbide (ZrC) films were chemically vapor deposited on $ZrO_2$ substrate using zirconium tetrachloride $(ZrCl_4),\;CH_4$ as a source and $H_2$ dilution gas, respectively. The change of input gas ratio was correlated with growth rate and morphology of deposited ZrC films. The growth rate of ZrC films increased as the input gas ratio decreased. The microstructure of ZrC films was changed with input gas ratio; small granular type grain structure was exhibited at the low input gas ratio. Angular type structure of increased grain size was observed at the high input gas ratio.