• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1387-1393
• /
• 1996

A study on mesophase pitch as a matrix precursor of carbon fiber reinforced carbon (C/C) composite has been recently presented. This study is concerned with the production of mesophase pitch as matrix precursors for C/C composite from coal tar pitch. A commercial coal tar pitch was heat-treated at 25$0^{\circ}C$ for 2 hours to remove low molecular weight fraction from the pitch then increasing the temperature of the pitch to between 350~45$0^{\circ}C$ to produce mesophase pitch. The pitch was continuously stirred during this time and nitrogen gas was continuously bubbled through the pitch. Spherical and bulk mesophases were formed in the pitch after heat-treatment,. Parent and mesophae pitches were characterized by elemental analysis coke yield solubi-lity in tetrahydrofuran and hexane and an optical microscopy to measure the mesiophase content. It was neces-sary to produce C/C composite that a mesophase pitch with about 30-40 vol% mesophase spherulites can be infiltrated into a fiber preform without a filter effect as a matrix precursor conditions. This condition was satisfied with mesophase pitch heat treated at 40$0^{\circ}C$ for 2 hours. The other heat treatment conditions showed the nuclei of mesophase or bulk mesophae which were not satisfied with the matix precursor condition.

• Journal of the Korean Ceramic Society
• /
• v.35 no.7
• /
• pp.740-748
• /
• 1998

The inertia friction properties of C/C composites manufactured by the processes of pressure and at-mospheric carbonizaton with a commerciallized and two kinds of modified coal-tar pitch as a matrix pre-cursor were investigated. The modifications of a pitch such as the introduction of mesophase and the ad-dition of sulphur into a raw pitch were not effective for a impregnation efficiency conducted in a vacuum and at the same time in a pressure of 5kg/cm2 due to the increase of the pitch viscosity. There was not a difference in the densification increment between the pitch modifications however it was revealed that a pressure carbonization was more advantageous than an atmospheric in the densification and the formation of anisotropic carbon matrix. The friction and wear propertis of C/C having higher degree of matrix cry-stallization higher density and hardness of friction surface showed superiority. As the braking energy was increased the friction coefficients were decreased and reached almost same level at the high kinetic energy of 99.6kJ. The wear trends at 99.6kJ were different from the behaviors of friction ceofficient under the same energy in which an oxidation wear is being considered along with a mechnical wear although the wear rates were almost similar to the friction coefficient at the low energy.

• Carbon letters
• /
• v.1 no.1
• /
• pp.6-11
• /
• 2000

Coal tar pitch was chemically modified with 10 wt% benzoquinone (BQ) to raise the softening point of isotropic pitch precursor and the precursor was melt-spun into pitch fibers, stabilized, carbonized and activated with steam at $900^{\circ}C$. The weight loss of carbon fiber-benzoquinone (CF-BQ) increased with the increase of activation time like other fibers, but was lower than those of Kureha fiber at the same activation time in spite of larger geometric surface area. Those adsorption isotherms fitted into 'Type I' according to Brunauer, Deming, Deming and Teller classification. However, there was very thin low-pressure hysteresis that lower closure points of the hysteresis are about 0.42-0.45. From the pore size distribution curves, there might be some micropores having narrow-necked bottle; a series of interconnected pore is more likely than discrete bottles. FT-IR studies showed that the functional groups such as carboxyl, quinone, and phenol were introduced to ACFs-BQ surface after steam activation. Methylene blue decolorization and iodine adsorption capacity of ACF-BQ increased linearly with the increase of specific surface area and was larger than that of ACF-Kureha at the same specific surface area.

• Fibers and Polymers
• /
• v.1 no.2
• /
• pp.97-102
• /
• 2000

Pitch precursors were synthesized from coal tar(CT) and pyrolysis fuel oil(PFO, petroleum residue oil) at relatively low temperature of $250^{\circ}$, in the presence of horontrifluorideidiethyletherate complex(BFDE) as a catalyst and nitrobenzene(NB) as a co-catalyst. The softening point, nitrogen content and carbon yield increased with an increase of concentration of NB. The pitch precursors with good spinnability were prepared by removing the volatile components through $N_2$ blowing. The precursor pitches were spun through a circular nozzle, stabilized at $310^{\circ}$ and finally carbonized at $1000^{\circ}$. The optically anisotropic structure formed at the absence of NB was changed into isotropic structure, showing a decrease in size of the flow domain. The hollow carbon fiber could be prepared in the process of stabilization. The results proposed that the morphology of carbon materials could be controlled by changing the concentration of catalyst and/or co-catalyst and/or stabilization condition that affect on the mobility of molecules during carbonization.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.6
• /
• pp.516-522
• /
• 2017

We report the growth of carbon nanotubes (CNT) on Invar-42 plates using coal tar pitch (CTP) by chemical vapor deposition (CVD) method. The solid phase CTP is used as an inexpensive carbon source since it produces a bunch of hydrocarbon gases such as $CH_4$ and other $C_xH_v$ by thermal decomposition over $450^{\circ}C$. The Invar-42 is a representative Ni-based ferrous alloy and can be used repetitively as a substrate for CNT growth because Ni and Fe are used as very active catalytic elements. We changed mixing ratio of carrier gases, argon and hydrogen, and temperature of growth region. It was found that the optimum gas ratio and temperature for high quality CNT growth are $Ar:H_2=400:400$ sccm and $1000^{\circ}C$, respectively. In addition, the carbon nanoball (CNB) was also obtained by just changing the mixing ratio to $Ar:H_2=100:600$ sccm. Finally, CTP can be employed as a versatile carbon source to produce various carbon-based nanomaterials, such as CNT and CNB.

• Applied Chemistry for Engineering
• /
• v.16 no.5
• /
• pp.712-718
• /
• 2005

This research was conducted to evaluate the effect of recycled-water addition on the treatment of coar tar-contaminated soil with slurry phase bioreactor. A bench-scale slurry phase bioreactor was maintained to optimize the microbial growth. Silty loam soil was used for this research. Concentrations of coal tar and 14 target PAHs (Polyunclear Aromatic Hydrocarbons) in the soil were determined with gas chromatography. Addition of recycled-water to slurry phase bioreactor was not significantly increased the removal efficiency of 2000 mg coar tar/kg. However, it significantly increased the removal efficiency of 20000 mg coar tar/kg. In 20000 mg coar tar/kg, the first order kinetic constant and the removal efficiency of the reactor with recycled-water addition were 2.5 and 2.0 times higher than those of the reactor without recycled- water addition. Coar tar in the slurry phase bioreactor was removed in 3.8~16.0% by vaporization and biodegraded in 84.0~96.2%. Removal efficiency of 3-ring compounds was high as 92.2~99.7% in the case of recycled-water addition. However, removal efficiencies of 3 and 4-ring compounds were low as 0~30%.

• Applied Chemistry for Engineering
• /
• v.25 no.2
• /
• pp.142-146
• /
• 2014

The separation of nitrogen heterocyclic compound (NHC) contained in a model coal tar fraction of nine components system was investigated by distribution equilibrium. The model coal tar fraction comprising NHC group (NHCs; indole (In), quinoline (Q), iso-quinoline (iQ), quinaldine(Qu)), bicyclic aromatic compound group (BACs; 1-methylnaphthalene (1MN), 2-methylnaphthalene (2MN), dimethylnaphthalene (DMN)), biphenyl (Bp) and phenyl ether (Pe) and the aqueous methanol were used as the raw materials and the solvent of this work, respectively. A batch-stirred tank was used as the liquid-liquid contact unit of this work. The distribution coefficient of NHCs increased by increasing the equilibrium operation temperature, whereas the selectivity of NHCs with respect to BACs decreased. Decreasing the initial volume ratio of water to the solvent resulted in deteriorating the selectivity of NHCs in reference to BACs, but improving the distribution coefficients of NHCs. At a fixed experimental condition, the sequence of the distribution coefficient and the selectivity with reference to BACs for each groups was increased in order of NHCs > Bp > BACs > Pe and NHCs > Bp> Pe, respectively. Also, the sequence of the distribution coefficient for entire compounds was in order of In > iQ = Q > Qu > Bp > 1MN = 2MN > Pe > DMN. The maximum yield of NHCs and the selectivity of NHCs based on BACs obtained by methanol extraction were 94 and 23%, respectively. Furthermore, the recovery process for NHCs from coal tar was studied by using the experimental results from this work.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2004.10a
• /
• pp.90.3-90.3
• /
• 2004

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.5
• /
• pp.442-451
• /
• 2010

This paper describes the calculation method to obtain the product composition of coal pyrolysis at high pressure and high temperature. The products of coal pyrolysis should be determined for the coal gasifier simulation, and this is the first step of the coal gasifier simulation. The pyrolysis product distribution greatly affects the coal gasifier efficiency such as carbon conversion, cold gas efficiency and the syngas composition at the outlet of the gasifier. The present calculation method is based on the coal ultimate/proximate analysis and several correlations among gasifier pressure, coal properties and pyrolysis products. The calculated products for 5 coals have been compared with those from the commercial pyrolysis model.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.12
• /
• pp.1000-1006
• /
• 2009

Integrated Coal Gasification Combined Cycle (IGCC) power plants have been developed to reduce carbon dioxide emissions and to increase the efficiency of electricity generation. A devolatilization process of entrained coal gasification is predicted by CPD model which could describe the devolatilization behavior of rapidly heated coal based on the chemical structure of the coal. This paper is intended to compare the mass release behavior of char, tar and gas(CO, $CO_2,\;H_2O,\;CH_4$) for three different coals. The influence of coal structure on gas evolution is examined over the pressure range of 10${\sim}$30atm.