• Journal of Environmental Health Sciences
• /
• v.36 no.2
• /
• pp.136-140
• /
• 2010

The integrated gasification combined cycle (IGCC) is one of the most promising proposed processes for advanced electric power generation that is likely to replace conventional coal combustion. This emerging technology will not only improve considerably the thermal efficiency but also reduce or eliminate the environmentally adverse effects normally associated with coal combustion. The IGCC process gasifies coal under reducing conditions with essentially all the sulfur existing in the form of hydrogen sulfide ($H_2S$) in the product fuel gas. The need to remove $H_2S$ from coal derived fuel gases is a significant concern which stems from stringent government regulations and also, from a technical point of view and a need to protect turbines from corrosion. The waste seashells were used for the removal of hydrogen sulfide from a hot gas stream. The sulphidation of waste seashells with $H_2S$ was studied in a thermogravimetric analyzer at temperature between $600^{\circ}C$ and $800^{\circ}C$. The desulfurization performance of the waste seashell sorbents was experimentally tested in a fixed bed reactor system. Sulfidation experiments performed under reaction conditions similar to those at the exit of a coal gasifier showed that preparation procedure and technique, the type and the amount of seashell, and the size of the seashell affects the $H_2S$ removal capacity of the sorbents. The pore structure of fresh and sulfided seashell sorbents was analyzed using mercury porosimetry, nitrogen adsorption, and scanning electronmicroscopy.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3125-3130
• /
• 2008

Coal is one of the most abundant and cheapest energy sources in the earth, but its typical combustion product, $CO_2$, is related with serious recent environmental issues such as global warming. The Integrated Coal Gasification Combined Cycle (IGCC) with $CO_2$ sequestration is one of the most promising options to produce electricity using a relatively cheap fuel (coal) with minimum impact on environment. In IGCC power generation systems, some chemical reactions are required to gasify coal to produce syngases such as $H_2$ and CO, which would be burnt in the combustor to produce heat for power generation, with a penalty of additional energy consumption. In this paper, several chemical reactions for the gasification of coal are considered and their characteristics are investigated.

• Journal of the Korean Ceramic Society
• /
• v.54 no.2
• /
• pp.128-136
• /
• 2017

Fly ash from a circulating fluidized bed combustion boiler (CFBC fly ash) is very different in mineralogical composition, chemical composition, and morphology from coal ash from traditional pulverized fuel firing because of many differences in their combustion processes. The main minerals of CFBC fly ash are lime and anhydrous gypsum; however, due to the fuel type, the strength development of CFBC fly ash is affected by minor components of active $SiO_2$ and $Al_2O_3$. The initial hydration product of the circulating fluidized bed combustion fly ash (B CFBC ash) using petro coke as a fuel is Portlandite which becomes gypsum after 7 days. Due to the structural features of the portlandite and gypsum, the self-cementitious strength of B CFBC ash was low. While the hydration products of the circulating fluidized bed combustion fly ash (A CFBC ash) using bituminous coal as a fuel were initially portlandite and ettringite, after 7 days the hydration products were gypsum and C-S-H. Due to the structural features of ettringite and C-S-H, A CFBC ash showed a certain degree of self-cementitious strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.293-298
• /
• 2002

Recycling of coal combustion by-product(Ash) are becoming more improtant in the utilization business as a result of the increased use of NOx reduction technologies at coal-fired power plants. current disposal methods of these by-products create not only a loss of profit for the power industry, but also environmental concerns that breed negative public opinion. This research made concrete crecast block using coal ash artificial aggregate for environmental-friendly products and compared strength special quality of this block with existent common use brick and analyzed application possibility in situ with a reserve experiment that measured strength property and manufactured method to handle coal ash produced in Bo-ryung thermoelectric power plant.

• Journal of Energy Engineering
• /
• v.16 no.1 s.49
• /
• pp.32-39
• /
• 2007

Coal pyrolysis processes vary with the origin and rank of coal. It is difficult to generalize the characteristics of coal pyrolysis reaction because the process consists of numerous reactions including pyrolysis, gasification, and combustion. To find out the optimum process condition it is necessary to determine the condition fur each coal from the smatter scale experiment. In this study pressurized ($2kg_{f}/cm^{2}$) fluidized bed, low temperature ($735{\sim}831^{\circ}C$) gasification using Kideco coal was performed. The reaction condition and product gas composition were determined from the variables including steam flow rate, coal feed rate and air flow rate. Optimum reaction condition was determined from the concentrations of $H_{2}$, and CO in the product gas. The ratio of air/coal was 4.45 and that of steam/coal was 0.21 respectively. The concentrations of CO and $H_{2}$ decreased with the increase of $CO_{2}$. It is important to control the feed rates of coal and steam because the reaction temperature rapidly increased when the combustion reaction dominates over the gasification reaction. The concentrations of CO and $H_{2}$ were 18%, 17% respectively from the continuous operating condition.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.2
• /
• pp.57-63
• /
• 2007

Coal combustion by-product (CCB) bottom ash, obtained from burning of pulverized coal, has physical properties which are similar to that of natural sand with particle sizes ranging from fine gravel to fine sand. Several studies have been completed to utilize pulverized coal combustion (PCC) bottom ash as a partial or full replacement of fine aggregate in cement concrete products. The objectives of this study were to develop air-entrained concrete composites using PCC bottom ash from burning of Illinois coal and to demonstrate the use of these composites on real-world projects. The results obtained show that the compressive, splitting-tensile, and flexural strengths of concrete composites is slightly lower than that of conventional concrete are early curing ages. However, after 60 days of curing, the strength of concrete composites is either equal to or slightly higher than that of an equivalent conventional concrete. The concrete composites showed lower resistance to chloride ion penetrability than that of an equivalent conventional concrete at early curing ages. However, after 28 days of curing, concrete composites showed better resistance to chloride ion penetrability compared to that of an equivalent conventional concrete.

• Environmental Engineering Research
• /
• v.25 no.4
• /
• pp.522-528
• /
• 2020

To achieve the clean and efficient utilization of low-rank coal, the combustion and pollutant emission characteristics of chars from low-temperature and fast pyrolysis in a horizontal tube furnace were investigated in a TG-MS analyzer. According to the results, the combustion characteristic of chars was poorer than its parent coals. The temperature range of gaseous product release had a good agreement with that of TGA weight loss. Gaseous products of samples with high content of volatile were released earlier. The NO and NO₂ emissions of chars were lower than their parent coals. Coals of high rank (anthracite and sub-bituminous) released more NO and NO₂ than low rank coals of lignite, so were chars from coals of different ranks. SO₂ emissions of char samples were lower than parent coals and did not show obvious relationship with coal ranks.

• Journal of the Korean Society of Combustion
• /
• v.20 no.2
• /
• pp.1-13
• /
• 2015

Drying, which is the oldest and most energy-intensive process, is an essential process for treatment of solid product. The specific procedure to design and evaluate the dryers, which are a rotary kiln dryer and a flash dryer, in case of drying the high-moisture coal was described. From determination of size to the heat and mass balance in one-dimensional model were conducted to evaluate the performance of dryers. Heat consumption, inlet gas temperature and size of the dryers were compared between a rotary kiln dryer and a flash dryer. Further considerations to evaluate the reactor elaborately were also discussed. Performance simulation of dryers along with the design procedure described here will provide helpful basis for understanding the concept of reactor design.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.3
• /
• pp.285-292
• /
• 2012

The integrated gasification combined cycle (IGCC) system is well known for its high efficiency compared with that of other coal fueled power generation system. IGCC offers substantial advantages over pulverized coal combustion when carbon capture and storage (CCS) is required. Commercial plants employ different types of quenching system to meet the purpose of the system. Depending on that, the downstream units of IGCC can be modeled using different operating conditions and units. In case with $CO_2$ separation and capture, the gasifier product must be converted to hydrogen-rich syngas using Water Gas Shift (WGS) reaction. In most WGS processes, the water gas shift reactor is the biggest and heaviest component because the reaction is relatively slow compared to the other reactions and is inhibited at higher temperatures by thermodynamics. In this study, tehchno-econimic assessments were found according to the quench types and operating conditions in the WGS system. These results can improve the efficiency and reduce the cost of coal gasification.

• Resources Recycling
• /
• v.16 no.6
• /
• pp.28-33
• /
• 2007

Coal is the most abundant energy source and deposited in every area of world. Combustion process with lower efficiency has been mainly used. Therefore, implementation of more efficient technologies, involving gasification, combined cycles and fuel cells, would be a key issue in the plans for more efficient power generation. In these technologies, gasification has been studied for decades. However, coal gasification to high value combustible gas such as hydrogen and carbon monoxide is focused again due to high oil price. The gaseous product, called syngas, can be effectively utilized in a variety of ways ranging from electricity production to chemical industry (as feedstock). In this study, coal gasification with ultra high temperature steam has been performed. The effect of steam/carbon ratio on the produced gas concentrations, gasification rate and additional products like tar, ammonia and cyan compounds has been determined.