• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.4
• /
• pp.397-403
• /
• 2015

In this paper, a method of ISAR geometric calibration is represented by using impulse-radio UWB radar. The ir-UWB is good for using a signal processing in time domain, so, it does not occur a multi-path or coupling problem. If a signal that between antennas and target is assumed a plane wave, a center of rotation in ISAR geometry model can be estimated by using point target. Before image is reconstructed with sinogram, the center of rotation can be calculated by using least square fitting. This method can be obtained a more contrast image, and a maximum value of entropy of image. The method, that estimates a center of rotation in received data, will be used a initial setup of instruments or a periodic compensation to reconstruct image. It would be useful in medical, security and surveillance imaging equipments that have a fixed geometry.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.544-549
• /
• 2017

This paper aims to examine the effect of rotational fluid motion about the efficiency of the gas - liquid ejector, which is a core unit in a ship equilibrium water treatment system. The ejector is a device for injecting ozone into ship equilibrium by the negative pressure generated by exchange of momentum between water and ozone. The existing ejector ejects the driving fluid with a simple form. In this paper, however, a rotation induction device is applied to the driving nozzle so that the driving fluid can be rotated and injected. To investigate the flow characteristics by the rotational movement of the driving fluid, CFD was used. The pressure and flow rate of the driving fluid, the negative pressure and suction flow rate of the suction fluid in the suction part, and the discharge pressure were predicted. On the basis of the results, the efficiency of the ejector using the rotation induction system was 22.25%, which was about 1.7% better than that of the existing ejector. Finally, to verify the feasibility of the CFD, an experiment was conducted on the ejector using the rotation induction device and the results were similar to those of the CFD.

• Structural Engineering and Mechanics
• /
• v.88 no.1
• /
• pp.53-65
• /
• 2023

With the gradual implementation of long-span suspension bridges into high-speed railway operations, the main beam's bending stiffness contribution to the live load response permanently grows. Since another critical control parameter of railway suspension bridges is the beam-end rotation angle, it should not be ignored by treating the main beam deflection as the only deformation response. To this end, the current study refines the existing method of the main cable shape and simply supported beam bending moment analogy. The bending stiffness of the main beam is considered, and the main beam's analytical expressions of deflection and rotation angle in the whole span are obtained using the cable-beam deformation coordination relationship. Taking a railway suspension bridge as an example, the effectiveness and accuracy of the proposed analytical method are verified by the finite element method (FEM). Comparison of the results by FEM and the analytical method ignoring the main beam stiffness revealed that the bending stiffness of the main beam strongly contributed to the live load response. Under the same live load, as the main beam stiffness increases, the overall deformation of the structure decreases, and the reduction is particularly noticeable at locations with original larger deformations. When the main beam stiffness is increased to a certain extent, the stiffening effect is no longer pronounced.

• Journal of Dental Anesthesia and Pain Medicine
• /
• v.15 no.1
• /
• pp.25-29
• /
• 2015

Factor XI deficiency (Hemophilia C) is a very rare autosomal recessive bleeding disorder. Patients with factor XI deficiency do not typically show any spontaneous bleeding or specific symptoms. Sometimes those who have this disorder are identified during special situations such as trauma or surgery. Orthognathic surgery is particularly associated with a high bleeding risk. Therefore, great care must be taken when treating patients with bleeding disorders such as factor XI deficiency. There are a few reports that address the management of patients with bleeding disorders during orthognathic surgery. The current report describes a patient with factor XI deficiency who underwent Le Fort I osteotomy together with bilateral sagittal split osteotomy. The patient's condition was assessed using both rotation thromboelastometry ($ROTEM^{TM}$) and noninvasive measurements of total hemoglobin (SpHb) using Masimo Radical 7 (Masimo Co. CA, USA).

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.134-140
• /
• 2018

This paper describes the design and fabrication of an automatic alignment and loading system for workpieces. To move a workpiece to a chucking position of a machine tool using a gantry robot, an automatic aligning device is required to load the workpiece before machining and automatically align them. The automatic alignment system was conceptually designed, and the structural analysis was performed for the main parts such as the top plate, center support, front and back support, and support shaft. Based on the structural analysis results, the size of these structures was determined. The automatic alignment system was manufactured, and the vertical movement characteristics of the workpiece up-and-down movement device and the rotation characteristics of the workpiece rotation device were experimentally examined. The result has confirmed that they operate normally.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.305-310
• /
• 2004

We have studied the optimal phase retardation value of a homogeneously aligned liquid crystal (LC) driven by fringe-field when using the LC with positive dielectric anisotropy. In general, the transmittance of a homogeneous aligned LC cell under crossed polarizer is maximum when a twist angle of LC by in-plane rotation is 45$^{\circ}$ with polarizer and the cell retardation becomes λ/2. However, the device using the LC with positive dielectric anisotropy does not follow this since the degree of rotation of the LC is dependent on electrode position and in addition the LCs tilt up along the fringe-field. At the center of common and pixel electrode, the LC is most twisted around a middle position of a cell whereas at the edge position of pixel electrode, the LC is most twisted near bottom surface of a cell. Consequently, the optimal phase retardation of the device becomes much larger than λ/2 and the transmittance can be described using the combination of the in-plane switching and twisted nematic mode.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.9
• /
• pp.52-59
• /
• 2009

In this paper, the planar waveguide slotted array antenna is presented, which has the 3-layered structure of feeding networks for a high gain. Due to the ionosphere which generates 'Faraday rotation', the skew is happened between the signal radiated from an artificial satellite and the receiving antenna. This causes a polarization loss. In this paper, to remove this polarization loss, the dumbbell shaped linear polarizer using a single layer film is proposed. The gain of proposed antenna is 29.4dB.

• Journal of Power System Engineering
• /
• v.21 no.2
• /
• pp.77-82
• /
• 2017

In the fishing boat, freshwater ice is loaded on the fishroom in advance and it is used for storage of fishes. However, it causes degradation of catches' freshness. Therefore, seawater ice machine on board is necessary for the fishing industry. In this study, seawater ice machine with drum type evaporator was manufactured, and the system was tested under various operating conditions having an influence on the COP and amount of ice produced. The main results are as follow : The COP of the system gets larger when the evaporation temperature and rotation speed of the drum in the evaporator increases. The most effective refrigerant is R22 and the value of the COP was 1.43 times higher than that of R404A. The amount of produced ice increases with respect to increment of the evaporation temperature, while that decreases with respect to increment of the evaporator drum rotation speed.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.46.3-47
• /
• 2018

We present a general N-body exasolar system simulator in anticipation of upcoming searches for exoplanets and even exomoons by next generation telescopes such as James Webb Space Telescope. For habitable zones, traditionally defined by temperature, we here address the essential problem of dynamical stability of planetary orbits. Illustrative examples are presented on P-type orbits in stellar binary systems, that should be fairly common as in Kepler 16b. Specific attention is paid to reduced orbital lifetimes of exoplanets in the habitable zone by the stellar binary, that is propoesed by Maurice van Putten (2017). Especially, we focused on a classic work of complex three-body problem that is well known by Dvorak(1986). We charge his elliptic restricted three-body problem to extend unrestricted three-body problem to look into dynamical motions in view of circumbinary planet, furthermore, we suggest that opposite angular orientation of the planet is relative to the stability of orbits. In here, counter-rotation case is relatively more faster than co-rotation case for being stable. As a result, we find that various initial conditions and thresholds to approach dynamical stability and unstability with unexpectable isolated islands over enormous parameter space. Even, superkeplerian effect of binary is important to habitability of the exoplanet and we can verify that superfaster binary doesn't effect on th planet and increases survivality of planet around the binary.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.446-449
• /
• 2000

A direct RTI(Rotation and translation invariant) fingerprint identification is proposed using the GCMs(generalized complex moments) and Gabor filter-based features from the grey level fingerprint around core point. The core point is located as reference point for the translation invariant matching. And its symmetry axis is detected for the rotation invariant matching from its neighboring region centered at the core point. And then, fingerprint is divided into non-overlapping blocks with respect to the core point and, in contrast to minutiae-based method using various processing steps, features are directly extracted from the blocked grey level fingerprint using Gabor filter, which provides information contained in a particular orientation in the image. The Proposed fingerprint identification is based on the Euclidean distance of the corresponding Gabor features between the input and the template fingerprint. Experiments are conducted on 300 ${\times}$ 300 fingerprints obtained from the CMOS sensor with 500 dpi resolution, and the proposed method could obtain 97% identification rate.