• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.159-159
• /
• 2008

Indium-tin oxides (ITO) films have been widely used as transparent electrodes for optoelectronic devices such as organic light emitting diodes (OLEDs), photovoltaics, touch screen devices, and flat-paneldisplay. In particular, to improve hole injection efficiency in OLEDs, transparent electrodes should have high work-function besides their transparency and low resistivity. Nevertheless, few studies have been made on engineering the work function of ITO for use as an efficient anode. In this study, the effects of a wide range of Nb or Zn doping rate on the changes in work functions of ITO anode were investigated. The Nb or Zn doped ITO films were fabricated on glass substrates using combinatorial sputtering system which yields a linear composition spread of Nb or Zn concentration in ITO films in a controlled manner by co-sputtering two targets of ITO and Nb2O5 or ITO and ZnO. We have also examined the resistivity, transmittance, and other structural properties of the Nb or Zn-doped ITO films. Furthermore, OLEDs employing Nb or Zn-doped ITO anodes were fabricated and the device performances were investigated concerned with the work function changes.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1488-1490
• /
• 2000

ZnO:Cu thin films are deposited by using an RF magnetron co-sputtering system with Cu chips attached on ZnO target. Structural and electrical properties are analyzed as a function of deposition conditions, such as Cu chip areas, $O_2/(Ar+O_2)$ ratios, and working pressures, The results show that a higher electrical resistivity above $10^{10}$ ${\Omega}cm$ along with an excellent c-axial growth can be easily achieved by Cu-doping. SAW filters based on the ZnO:Cu films are also fabricated to estimate the electric-mechanical coupling coefficient($K^{2}_{eff}$). Higher $K^{2}_{eff}$ and lower insertion losses are observed for ZnO:Cu films, compared with those for ZnO films.

• Bulletin of the Korean Chemical Society
• /
• 제34권5호
• /
• pp.1445-1453
• /
• 2013

$Zn_{(1-x)}Ni_xAl_2O_4$ (x = 0.0-1.0) spinels were prepared at $800^{\circ}C$ by co-precipitation method and characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy. The specific surface area was determined by BET. SEM image showed nano sized spherical particles. XPS confirmed the valence states of the metals, showing moderate Lewis character for the surface of materials. The powders were successfully used as new heterogeneous catalysts of Biginelli's reaction, a one-pot three-component reaction, leading to some dihydropyrimidinones (DHPMs). These new catalysts that produced good yields of DHPMs, were easily recovered by simple filtration and subsequently reused with persistent activity, and they are non-toxic and environmentally friendly. The optimum amount of catalyst is 20% by weight of benzaldehyde derivatives, while the doping amount has been found optimal for x = 0.1.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.393-402
• /
• 2007

Polyaluminocarbosilane was synthesized by direct reaction of polydimethylsilane with aluminum(III)-acetylacetonate in the presence of zeolite catalyst. A fraction of higher molecular weight polycarbosilane was formed due to the binding of aluminium acetylacetonate radicals with the polycarbosilane backbone. Small amount of Si-O-Si bond was observed in the as-prepared polyaluminocarbosilane as the result. Polyaluminocarbosilane fiber was obtained through a melt spinning and was pyrolyzed and sintered into SiC fiber from $1200{\sim}2000^{\circ}C$ under a controlled atmosphere. The nucleation and growth of ${\beta}-SiC$ grains between $1400{\sim}1600^{\circ}C$ are accompanied with nano pores formation and residual carbon generation. Above $1800^{\circ}C$, SiC fiber could be sintered to give a fully crystallized ${\beta}-SiC$ with some ${\alpha}-SiC$.

• 센서학회지
• /
• 제17권5호
• /
• pp.361-368
• /
• 2008

Nanosized $SnO_2$ particles were synthesized by homogeneous precipitation method using tin chloride ($SnCl_4{\cdot}5H_{2}O$) and urea ($CO(NH_2)_2$). The powders were heated at $500^{\circ}C$ and $600^{\circ}C$ for 2h. The crystal structure, microstructure, thermal behavior, specific surface area were analyzed using XRD, FE-SEM, TGA and BET, respectively. The initial resistance and the $H_2$ sensing properties were measured as a function of ${Sb_2}{O_3}$ and Pd doping concentrations. The resistance was decreased with the addition of ${Sb_2}{O_3}$ and the sensitivity for $H_2$ gas was increased with the addition of Pd. Thus, the optimum $H_2$ gas sensing property was obtained in the 0.25.mol% ${Sb_2}{O_3}$ and 1.w% added $SnO_2$ powders.

• 센서학회지
• /
• 제22권4호
• /
• pp.302-307
• /
• 2013

The Sb-doped $SnO_2$ nanowire network sensors were prepared by thermal evaporation of the mixtures between tin and antimony powders. Pure $SnO_2$ nanowire networks showed high sensor resistance in air ($99M{\Omega}$), similar gas responses to 4 diffferent gases (5 ppm $C_2H_5OH$, CO, $H_2$, and trimethylamine), and very sluggish recovery speed (90% recovery time > 800 s). In contrast, 2 wt% Sb-doped $SnO_2$ showed the selective detection toward $C_2H_5OH$ and trimethylamine, relatively low resistance ($176k{\Omega}$) for facile measurement, and ultrafast recovery speed (90% recovery times: 6 - 18 s). The change of gas sensing charactersitics by Sb doping was discussed in relation to gas sensing mechanism.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.843-847
• /
• 2014

In Super Junction (SJ) MOSFETs, charge balance is the most important issue of the SJ fabrication process. In order to achieve the best electrical characteristics, such as breakdown voltage and on-resistance, the N-type and P-type drift regions must be fully depleted when the drain bias approaches the breakdown voltage, which is known as the charge balance condition. In conventional charge balance analysis, based on multi-epi process SJ MOSFETs, analytical model has only N, P pillar width and doping concentration parameter. But applying a conventional charge balance principle to trench filling process, easier than Multi-epi process, is impossible due to the missing of the trench angle parameter. To achieve much more superior characteristics of on-resistance in trench filling SJ MOFET, the appropriate trench angle is necessary. So in this paper, modulated charge balance analysis is proposed, in which a trench angle parameter is added. The proposed method is validated using the TCAD simulation tool.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.294-294
• /
• 2007

Spinel cathode material $LiMn_2O_4$ is currently studied as a promising cathode material for lithium ion secondary batteries for future applications because of it is low cost, easy to be prepared and capable to be operated in high voltage range. However as a cathode material, $LiMn_2O_4$ performs a poor capacity retention which leads to short cycle life. In this study, stoichiometric $LiMn_2O_4$ was synthesized with granulation method with ion substitution to stabilize its structure and niobium doping to improve its conductivity. These well-mixed powders were calcined at $850^{\circ}C$ for 6 hours and its properties were investigated. Correlations of dopant and electrochemical properties were examined as well.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.44-45
• /
• 2006

초고용량 캐패시터(Supercapacitor)는 이차전지와 더불어 차세대 전지로 분류되는 신형에너지 장치로서 충 방전 속도가 다르고 순간 전력공급이 가능하며 충 방전 수명이 반영구적으로 길고 고출력을 내기 때문에 이차전지가 갖지 못하는 영역에서 동력에너지원으로 사용된다. 본 연구에서는 초고용랑 캐패시터의 전극소재인 탄소계 재료를 대신하여 비탄소계 전극소재인 $Li_4Ti_5O_{12}$의 고상법 제조를 위한 Li/Ti의 최적 조성과 혼합 방법으로 Li-Ti 계에 $Fe_2O_3$, NiO, $Nb_2O_5$, $Sb_2O_3$ 그리고 ZnO와 같은 금속산화물로 치환시켜 합성된 Li -Ti계 금속산화물의 특성 및 충 방전 효과에 미치는 영향을 관찰하고자 하였다.

• 한국재료학회지
• /
• 제18권2호
• /
• pp.61-64
• /
• 2008

Electrical optical switching and structural transformation of $Ge_{15}Sb_{85}$, $Sb_{65}Se_{35}$ and N2.0 sccm doped $Sb_{83}Si_{17}$ were studied to investigate the phase change characteristics for PRAM application. Sb-based materials were deposited by a RF magnetron co-sputtering system and the phase change characteristics were analyzed using an X-ray diffractometer (XRD), a static tester and a four-point probe. Doping Ge, Se or Si atoms reinforced the amorphous stability of the Sb-based materials, which affected the switching characteristics. The crystallization temperature of the Sb-based materials increased as the concentration of the Ge, Se or Si increased. The minimum time of $Ge_{15}Sb_{85}$, $Sb_{65}Se_{35}$ and N2.0 sccm doped $Sb_{83}Si_{17}$ for crystallization was 120, 50 and 90 ns at 12 mW, respectively. $Sb_{65}Se_{35}$ was crystallized at $170^{\circ}C$. In addition, the difference in the sheet resistances between amorphous and crystalline states was higher than $10^4{\Omega}/{\gamma}$.