• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.125-131
• /
• 2006

Dimethyl ether (DME) is a new clean fuel as an environmentally-benign energy resource. DME can be manufactured from various energy sources including natural gas, coal, biomass and spent plastic. In addition to its environmentally friendly properties, DME has similar characteristics to those of LPG. Therefore, it is considered as an excellent substitute fuel for LPG, fuel cells, power plant, and especially diesel and is expected to be the alternative fuel by 2010. The experimental study of the direct synthesis of DME was investigated under various conditions over a temperature range of $220{\sim}280^{\circ}C$, syngas ratio 1.2~3.0. All experiments were carried out with a hybrid catalyst, composed of a methanol synthesis catalyst ($Cu/ZnO/Al_2O_3$) and a dehydration catalyst (${\gamma}-Al_2O_3$). The observed reaction rate follows qualitatively a Langmiur-Hinshellwood model as the reaction mechanism. Such a mechanism is considered with three reactions; methanol synthesis, methanol dehydration and water gas shift reaction. From a surface reaction with dissociative adsorption of hydrogen, methanol, and water, individual reaction rate was determined.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.71-77
• /
• 2012

When a new bonding agent using coal ash is utilized as a substitute for cement, it has the advantages of offering a reduction in the generation of carbon dioxide and securing the initial mechanical strength such that the agent has attracted strong interest from recycling and eco-friendly construction industries. This study aims to establish the production conditions of new hardening materials using clean bottom ash and an alkali activation process to evaluate the characteristics of newly manufactured hardening materials. The alkali activator for the compression process uses a NaOH solution. This study concentrated on strength development according to the concentration of the NaOH solution, the curing temperature, and the curing time. The highest compressive strength of a compressed body appeared at 61.24MPa after curing at $60^{\circ}C$ for 28 days. This result indicates that a higher curing temperature is required to obtain a higher strength body. Also, the degree of geopolymerization was examined using a scanning electron microscope, revealing a micro-structure consisting of a glass-like matrix and crystalized grains. The microstructures generated from the activation reaction of sodium hydroxide were widely distributed in terms of the factors that exercise an effect on the compressive strength of the geopolymer hardening bodies. The Si/Al ratio of the geopolymer having the maximum strength was about 2.41.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.6
• /
• pp.1-10
• /
• 2012

The annual energy production of Gangwon wind farm was predicted for three consecutive years of 2007, 2008 and 2009 using commercial programs, WindPRO and WindSim which are known to be used the most for wind resource prediction in the world. The predictions from the linear code, WindPRO, were compared with both the actual energy prediction presented in the CDM (Clean Development Mechanism) monitoring report of the wind farm and also the predictions from the CFD code, WindSim. The results from WindPRO were close to the actual energy productions and the errors were within 11.8% unlike the expectation. The reason for the low prediction errors was found to be due to the fact that although the wind farm is located in highly complex terrain, the terrain steepness was smaller than a critical angle($21.8^{\circ}$) in front of the wind farm in the main wind direction. Therefore no flow separation was found to occur within the wind farm. The flow separation of the main wind was found to occur mostly behind the wind farm.

• Journal of the Korean Society of School Health
• /
• v.8 no.2
• /
• pp.293-303
• /
• 1995

Health has occupied a position of importance in the human history, whether it be in the East or in the West, and it is a subject in which people have been constantly interested. The concept of health has changed continuously as the society has developed, industrialized and become more structured. The perception of health concept can be an esential factor which is to determine the health behaviors. This study is a descriptive inquiry done to identity high school students' perception of health and what they do as health behaviors. The subject consisted of 503 voctional high school seniors, 129 boys and 374 girls, from a school located in An-san Si, kyong-gi Do. The instruments used for this study were open-ended questionnaires and data were collected by having the students fill out the questionnaires which took 10 minutes, in their first class, April 6, 1995. The collected materials were classified and recorded on the cards according to each question using the terms which students had written. After putting statements which had common meanings together, the representative categories were labelled. The results obtained are as follows. 1. Categorizing and labelling of health concepts What high school students descripted as health concepts were classified as the absence of illness, physical comfort, strong physical strength and physique, not having a deformity, resisting power, self control mental-rest(or psychological comfort), wholesome ideas, self-control, harmony in body and in mind, maintenace of daily life, pleasant life, good friends, peaceful family life and realizing objectives. 2. Categorizing and labelling of health behaviors These were classified as preventive life, good dietary habits and regimen, maintenance of clean body, exercises, preventing obesity, rest, environmental balance or control of environment, limit one's tastes, making use of leisure, peaceful mind, sound thought and regular living habits. The result indicates that the health concepts were positive and included not only absence of illness but also harmony in body and in mind and pleasant life; health behaviors which had high frequency were good dietary habits and regimen, exercises and sound thought. It is hoped that these findings well serve as practical references for teachers when they counsel with, and provide the students with guidance programs which include health care.

• Resources Recycling
• /
• v.10 no.3
• /
• pp.14-22
• /
• 2001

For the recycle of coal fly ash generated from power stations, we developed an electrocyclone system which can separate unburned carbon form coal fly ash, based on the fact that coarse fly ash particles contain higher amount of unburned carbon and unburned carbon particles are charged positively, and pure ash particles are charged negatively on contacting each other. Additionally, guide vanes were installed in the cyclone to control the cut size. Two types of electrode, stick and grid type, were designed to investigate the effect of electrode type. Results show that by introducing an electric field inside the cyclone, the yield increases by 5 to 15e1o. But the content of unburned carbon in the clean ash does not change significantly.

• Journal of the Korean Ceramic Society
• /
• v.42 no.9 s.280
• /
• pp.618-623
• /
• 2005

HTGR (High Temperature Gas-Cooled Reactor) is highlighted to next generation power plant for producing the clean hydrogen gas. In this study, the spherical $UO_2$ kernel via $UO_3$ gel particles was prepared by the sol-gel process. Raw material of slightly Acid Deficient Uranyl Nitrate (ADUN) solution, which has pH = 1.10 and $[NO_3]/[U]$ mole ratio = 1.93, was obtained from dissolution of $U_3O_8$ powder with conc.-$HNO_3$. The surface of these spherical $UO_3$ gel particles, which was prepared from the broth solution, consisted of 1 M-uranium, 1 M-HMTA, and urea, were covered with the fine crystallite aggregates, and these particles were so hard that crushed well. But the other $UO_3$ gel particles prepared with the broth solution, consisted of 2 M-uranium, 2 M-HMTA, and urea, have soft surface characteristics and an amorphous phase. This type of $UO_3$ gel particles is some chance of doing possibility of high density from the compaction. The amorphous $UO_3$ gel particles was converted to $U_3O_8$ and then $UO_2$ by calcination at $600^{\circ}C\;in\;4\%\;-\;H_2\;+\;N2$ atmosphere.

• Journal of Agricultural Extension & Community Development
• /
• v.8 no.2
• /
• pp.263-271
• /
• 2001

The purpose of this study were to review the current problems of rural welfare and to suggest desirable direction for development of welfare in rural Korea. Specific objectives of the study were to investigate the current status and problems of rural welfare and to search for the desirable directions for rural welfare development in Korea. The major findings of the study were as follows ; 1. Some of the current problems of rural welfare were; (1) difficulty in getting a job for stable income, (2) seriousness of medical care and aging of rural population, (3) decrease in number of rural school children and unfavorable educational environment, and (4) insufficiency in facility, manpower and program for recreation and cultural activities in rural area. 2. Problems of rural welfare were not independent in rural Korea, but the most of the problems were interrelated to each other. Integrated and comprehensive approach would be necessary to solve the problems of rural welfare. 3. Clean environment, stable and rewarding life, pride and self esteem of rural occupation should be the goals of better integrated rural welfare development, and healthfulness and quality of life should be ensured in rural society. 4. Urban oriented national policy based on urban centered political power was one of the causes of under development in rural welfare by creating rapid decrease in rural population and aging. Various problems in economic, educational, cultural and medical aspects of rural society should be solved. Further research on rural welfare should be conducted to increase and to strengthen rural welfare development in Korea.

• Journal of Biosystems Engineering
• /
• v.24 no.4
• /
• pp.309-316
• /
• 1999

This study was conducted to develop a large-scale rice polisher with double polishing stages for producing clean rice with high quality in rice processing complexs. The performance of the developed rice polisher was evaluated and improved. The results obtained from this study were as followings : 1. A large-scale rice polisher with double polishing stages was developed, which consisted of two polishing chambers(polishing part I and II), two spraying parts, a feeding part, power of 37kW, control panel, etc. Especially, the purpose of polishing part Iwere to uniformly mix white rice sprayed with water and to remove bran particles from the rice. the roller surface of the polishing part I was coated with chromium. 2. The capacity of the developed rice polisher was 4t/h. The broken rice rate of the polisher was less than 0.2%, compared with about 1% of others. 3. The whiteness increment of the developed polisher was 2.6~3.0% compared with about 2.3~2.5% of others. 4. The energy consumption of the developed polisher was 0.5kWh/100kg. 5. The developed polisher was improved with the angle change of screen slot of the polishing chamber I. The broken rice rate was reduced from about 0.5% to about 0.2% as the max. internal pressure of the polishing chamber II decreased by 0.4kg/$\textrm{cm}^2$ due to the increase of resistance in the polishing chamber I. The whiteness of the polisher showed more than 38~39. 6. The developed rice polisher showed high performance, compared with other domestic and foreign polishers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.163-170
• /
• 2016

Regulations for the exhaust gas of diesel vehicles are being strengthened every year. Recently, diesel emission regulations for HC, CO, NOx, and particulate matter (PM) have been subject to very strict standards. In the future, the regulation of PM is expected to become stricter. Accordingly, diesel particulate filters (DPFs) have been applied to most diesel vehicles for PM reduction. With increasing engine mileage, ash and soot from the engine exhaust gas accumulate inside the DPF. This accumulation can damage the DPF or degrade engine performance. Therefore, efficient cleaning of the DPF is critical for the maintenance of the engine. If the DPF is well managed through regular cleaning, it can improve the power and fuel economy of the engine and reduce maintenance costs. Therefore, this study was performed to develop a high-efficiency cleaning method for DPFs and an apparatus that can more effectively clean out the accumulated ash and soot.

• Journal of the Korean Society of Safety
• /
• v.21 no.4 s.76
• /
• pp.60-65
• /
• 2006

It is a well known fact that LCD is a central part of the IT industry which is important in the present and the future. But the biggest problem of LCD manufacturing is maintaining a cleaning room environment and administration. Therefore the purpose of this study is to first, prevent the yield depreciation and damage of products, and second, protect the worker ftom accidental electrostatic discharge during LCD manufacture. The soft x-ray ionizer is a type of electrostatic reducer device. It protects against electrostatic discharge in the cleaning room environment and is a necessary environmental factor during LCD production. The positive aspects of the soft x-ray are its shorter time and wider angle of exposure. But the negative aspect of the soft x-ray is its need for several shielding of protection from the harmful x-ray exposure. On this study, the development of the Air Nozzle-type ionizer to amend and refine some problems. For example, examined the electrostatic reduce device of a soft x-ray type and discovered the ion did not go inside well. also workers to be free from danger. An Air Nozzle-type ionizer is comprised of soft x-ray radiation and ionized air production. Air is injected through the nozzle after being ionized from radiation. It supplies air keeping the same pressure into the end foundation of ion production. The soft x-ray is the structure which radiates ionized air through the nozzle (21 holes) having micro holes of the ionizable radiation after ionizing the inside air by the ion production. A worker does not need a cover to protect against x-rays and the Air Nozzle-type ionizer is easy to set up and is more effective at eliminating electrostatic.