• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.10
• /
• pp.1465-1471
• /
• 2004

A trial was conducted to determine the effect of abrasive strips and abrasive paint in layer cages on claw length and claw sharpness, foot condition, feather cover and mortality of hens. During the preparation of the cages for the experiment it was simpler and took less time to apply the pre-prepared paint with a spatula to the egg guard compared to sticking the abrasive strips onto the egg guard. Fitting the strips took longer because it had to be cut from a 25 mm roll, cut into the appropriate lengths, the tape backing removed and then stuck onto the egg guard section. Abrasive paint was more effective as a claw shortener than abrasive strips. The birds using the abrasive paint had the shortest (p<0.05) claw length and lowest (p<0.05) claw sharpness. One of the original reasons for reducing claw length with claw shorteners was to reduce mortality by minimising skin skin abrasions caused by the claws. Surprisingly hen mortality from prolapse and cannibalism was higher (p<0.05) in cages fitted with abrasives. There are no other reports in the literature showing an increase in prolapse and cannibalism from hens using abrasives.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.28-34
• /
• 2014

A claw pole stepping motor is widely used in various fields such as a compact optical disk drive, computer peripherals, digital cameras, office automation(OA), handheld mobile devices, because it has the suitable structure for compact motor. However 3D analysis is essential for design of Claw pole stepping motor because of axial flux path. Thus, in general, it takes a lot of time in the design of Claw pole motor. In this paper, magnetic equivalent circuit considering axial flux was proposed to reduce design time of Claw pole motor and we has designed by using the magnetic equivalent circuit. In addition, in oder to verify the study, design model was verified by 3D FEM simulation and experiment.

• Journal of the Korean Vacuum Society
• /
• v.8 no.3B
• /
• pp.257-261
• /
• 1999

The claw pump, one of oil-less dry pumps developed to solve problems found in vacuum systems pumped by oil-sealed rotary pumps, has been widely used separately or as a part of compound structure with a roots pump. The claw pump has some merits such as a high pumping speed, a high compression ratio, and relatively little heat generation. The high compression ratio of the claw pump is compression ratio, and relatively little heat generation. The high compression ratio of the claw pump is based on efficient sweeping action of the special type rotor and an intrinsic self-valving mechanism. The contour of the rotor with claw-type blade is designed basically to make two rotors revolve smoothly without touching with each other, and related dimensions are determined by required pumping speed, compression ratio, power demand and diameter of the rotor axis. In this paper the procedure of designing the rotor of the claw pump is described and factors influencing the pump performance are analyzed.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.11
• /
• pp.597-603
• /
• 1999

Due to its simple construction, operation steadiness and low cost, claw pole step motor is widely used for OA machine and automobile. This paper deals with analysis fo claw pole motor, especially eyeing to dynamic characteristics. To analyze dynamic characteristics of claw pole step motor, torque development in each angular step of rotor are surveyed and torque equation is drived using permeance method. To adopt the airgap MMF, the magnetic equivalent circuit of the motor is introduced. On the base of the magnetic equivalent circuit, the air gap flux equation is derived. To get a optimum design of the motor, the torque characteristic is studied in variation of coil data and remanence value of permanent magnetic material.

• Korean Journal of Veterinary Service
• /
• v.42 no.4
• /
• pp.183-191
• /
• 2019

Claw lesion is one of the major causes of lameness in sows and the lameness is one of the reasons for culling of sows from the swine herd. This survey was conducted on sows in total of 8 farms with a total of 684 pigs. The lesions observed in the study were horizontal and vertical claw cracks (CWH & CWV), differences in the length of toes (T) and/or in the length of dew claws (DC) according to crates, breeds and parity of sows. Scores of claw lesions were assigned on 0, 1, 2, and 3 at each foot depending on the severity of the claw lesions. The sows' parity was classified into 1 to 2, 3 to 4, 5 to 8. Prevalence rate of claw lesions in sows raised on punched plastic crate was higher than that in sows raised on tribar crate. In prevlence rate by breeds, inbreed Landrace sows showed higher than that of Yorkshire sows. According to 4 claw lesions, the length of DC was the highest at parity 3~4 and CWV was the lowest at parity 3~4 in F1 crossbred sows raised on punched plastic crates, respectively. In Yorkshire breeds raised on punched plastic crates, the length of DC at parity 5~8 was the lowest and CWH was the highest at parity 3~4, respectively. In Landrace breeds raised on tribar crates, CWH was the highest at parity 1~2 and CWV was the lowest at parity 3~4, respectively. The high parity in F1 crossbred sows showed high prevalence rate of claw lesions than that of low parity and other inbreed sows, respectively. These results may be useful as elementary data in establishment of welfare quality protocol and preventive measures to reduce economic losses from craw lesions in sows.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.8
• /
• pp.80-87
• /
• 2006

This paper analyzed the characteristics of the claw pole PM stewing motor by using 3D FEM. As the magnetization occurs along the z-axis of the motor, it is necessary to apply 3D FEM for analysis of the claw pole PM stewing motor. Considering the computation time, reducing the number of the analysis model is effective method of the methods of the reducing analysis time. By using the "Design Of Experiments(DOE)", efficient analysis was able to be done. To see the effects of the design factors, the 3D FEM is applied only to the selected models. As the design factors, the teeth selected models, the number of turns and the permanent magnet overhang was selected.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.12
• /
• pp.125-132
• /
• 2013

This paper has done a three-dimensional FEM analysis of the PM claw pole stepping motor. As magnetization happens in the z-axis, which does not have a constant value, three-dimensional FEM analysis is necessary for characteristic analysis of PM claw pole stepping motors. Because it is a type of permanent magnet motor, the PM claw pole stepping motor naturally has a detent torque. This torque is known to show negative effects on motor performance. To improve motor performance, reducing the detent torque is very important during the motor design. This paper applied DOE for optimization of stator pole design of the motor. Also, we compared motor performance by applying a different type of rotor shape, dividing the permanent magnet. To verify the simulation results, an experiment was done.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.4
• /
• pp.412-418
• /
• 2012

Eddy current brakes are electromechanical devices used as variable mechanical loads for testing electrical machines. Accurate modeling of eddy current loss is an important t factor for optimum design of eddy brake systems. In this second part, we propose novel formulations of eddy current loss in novel claw-pole eddy brake system. The proposed model for eddy current loss in novel claw-pole eddy brake system depends on the size of the claw poles. Also, in this paper, the flux density is measured by using the magnetic circuit of the novel claw pole. The model results are compared with experimental results and they are found to be in good agreement.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.107-109
• /
• 2004

Stepping motors are widely used for various electric instruments. In case of analysing claw pole PM slopping motor 3-dimensional analysis is necessary for accurate field calculation. This paper presents static torque characteristics of a permanent magnet type stepping motor with claw poles using three-dimensional finite element analysis.

• Journal of Korean Foot and Ankle Society
• /
• v.7 no.2
• /
• pp.274-278
• /
• 2003

Rare complications of distal tibia fracture are claw-toe deformity, cavus deformity and checkrein deformity. These complications may be due to contracture of the muscles of the deep posterior compartment of the leg after a compartment syndrome. These 4 cases were treated by selective tendon lengthening of flexor tendon at the retromalleolar level.