• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.217-217
• /
• 2009

This paper describes the characteristics of polycrystalline 3C-SiC doubly clamped beam micro resonators. The polycrystalline 3C-SiC doubly clamped beam resonators with 60 ~ 100 ${\mu}m$ lengths, $10\;{\mu}m$ width, and $0.4\;{\mu}m$ thickness were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonant frequency was measured by a laser vibrometer in vacuum at room temperature. For the 60 ~ 100 ${\mu}m$ long cantilevers, the fundamental frequency appeared at 373.4 ~ 908.1 kHz. The resonant frequencies of doubly clamped beam with lengths were higher than simulated results because of tensile stress. Therefore, polycrystalline 3C-SiC doubly clamped beam micro resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• 한국전기전자재료학회논문지
• /
• 제22권4호
• /
• pp.303-306
• /
• 2009

This paper describes the characteristics of polycrystalline 3C-SiC doubly clamped beam micro resonators. The polycrystalline 3C-SiC doubly clamped beam resonators with $60{\sim}100{\mu}m$ lengths, $10{\mu}m$ width, and $0.4{\mu}m$ thickness were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonant frequency was measured by a laser vibrometer in vacuum at room temperature. For the $60{\sim}100{\mu}m$ long cantilevers, the fundamental frequency appeared at $373.4{\sim}908.1\;kHz$. The resonant frequencies of doubly clamped beam with lengths were higher than simulated results because of tensile stress. Therefore, polycrystalline 3C-SiC doubly clamped beam micro resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• Computers and Concrete
• /
• 제31권1호
• /
• pp.1-7
• /
• 2023

In this paper, Timoshenko-beam model is developed for the vibration of double carbon nanotubes. The resulting frequencies are gained for axial wave mode and length-to-diameter ratios. The natural frequency becomes more prominent for lower length-to-diameter ratios and diminished for higher ratios. The converse behavior is observed for axial wave mode with clamped-clamped and clamped-free boundary conditions. The frequencies of clamped-free are lower than that of clamped-clamped boundary condition. The eigen solution is obtained to extract the frequencies of double walled carbon nanotubes using Galerkin's method through axial deformation function. Computer softer MATLAB is used for formation of frequency values. The frequency data is compared with available literature and found to be in agreement.

• 대한토목학회논문집
• /
• 제29권3A호
• /
• pp.251-258
• /
• 2009

이 논문은 정다각형 중실 단면을 갖는 최강보에 관한 연구이다. 이 연구에서 보의 체적은 항상 일정하다. 이러한 보에 집중하중과 만재 사다리꼴 분포하중이 작용하는 경우에 탄성곡선의 미분방정식을 유도하고 이를 중적분법을 이용하여 풀어 정적 거동을 산정하였다. 미분방정식의 정적분은 Simpson 공식을 이용하였다. 수치해석 예에서는 고정-고정 보 및 고정-회전보를 채택하였고, 단면깊이의 형상함수로는 선형, 포물선형 및 정현형의 함수를 채택하였다. 이 연구에서 얻은 수치해석의 결과로부터 보의 정적 최대거동값이 최소가 되는 단면형상 즉 최강단면비를 산정하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.359-364
• /
• 1998

The effects of boundary conditions on natural frequencies for the ring stiffened composite cylindrical shells are investigated by theoretical method. The Love's thin shell theory and the discrete stiffener theory with beam functions in the Ritz procedure are used to derive the frequency equation. Five different boundary conditions such as clamped-clamped, simply supported-simply supported, free-free, clamped-free, clamped-simply supported are considered in this study. Also, the experimental investigation is presented to validate the theoretical results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권3호
• /
• pp.133-139
• /
• 2003

In this paper, a new control scheme of Class-E inverter for Induction Heating (IH) Jar applications with clamped voltage characteristics using Pulse-Frequency-Modulation (PFM) is introduced. To reduce the voltage stress of switch, the proposed PFM control scheme doesn't need any auxiliary circuit in comparison to a family of Active Clamped Class-E (ACCE) inverter. It can decrease voltage stress of switch through modulation of switching frequency. The Class-E inverter using the proposed control scheme has the advantage of not only the same output power when it is compared with a Hybrid-Active Clamped Class-E (Hybrid-ACCE) inverter but also Zero-Voltage-Switching (ZVS), which are characteristics of conventional Class-E and ACCE inverter. The control principles and analysis of proposed method are explained in detail and its validity is verified through simulation and experimental results.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.362-371
• /
• 2018

This work proposes FPGA implementation of Carrier Disposition PWM for closed loop seven level diode clamped multilevel inverter in speed control of induction motor. VLSI architecture for carrier Disposition have been introduced through which PWM signals are fed to the neutral point seven level diode clamped multilevel using which the speed of the induction motor is controlled. This proposed VLSI architecture makes the power circuit to work better with reduced stresses across the switches and a very low voltage and current total harmonic distortion (THD). The output voltages, currents, torque & speed characteristics for seven level neutral point diode clamped multilevel inverter for AC drive was studied. It has observed the proposed scheme introduces less distortion and harmonics. The results were validated using real time results.

• 대한기계학회논문집A
• /
• 제28권2호
• /
• pp.143-148
• /
• 2004

This paper discussed on the stability of elastic material subjected to dry friction force for low boundary conditions: clamped free, clamped-simply supported, simply supported-simply supported, clamped-clamped. It is assumed in this paper that the dry frictional force between a tool stand and an elastic material can be modeled as a distributed follower force. The friction material is modeled for simplicity into a Winkler-type elastic foundation. The stability of beams on the elastic foundation subjected to distribute follower force is formulated by using finite element method to have a standard eigenvalue problem. It is found that the clamped-free beam loses its stability in the flutter type instability, the simply supported-simply supported beam loses its stability in the divergence type instability and the other two boundary conditions the beams lose their stability in the divergence-flutter type instability.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.836-839
• /
• 2005

The in-plane vibration response of a clamped circular plate should be predicted in many applications. Up to now, papers on the in-plane vibration of rectangular plate are published. However, analytical derivation on the in-plane vibration of the clamped circular plate is not carried out. Therefore, the in-plane vibration of the clamped circular plate is the concern of this paper. In order to derive the equations of motion for the clamped circular plate in the cylindrical coordinate, the kinetic energy and potential energy for the in-plane behavior are obtained by us ing the stress-strain-displacement expressions. Application of Hamilton's principle leads to two sets of differential equations. These displacement equations were highly coupled. It is possible to obtain a simpler set of equations by introducing Helmholtz decomposition. Substituting them into the coupled differential equations, we obtain the uncoupled equations of motion. In order to solve them, we assume that the solutions are harmonic. Then, they lead to the wave equations. Using the separation of variable, we obtain the general solutions for the equations. Based on the solutions, the displacements for r and $\theta$ direction are assumed. Finally we obtain the frequency equation for the clamped circular plate by the application of boundary conditions. The derived equation is compared with the finite element analysis for validation by using the some numerical examples.

• Nuclear Engineering and Technology
• /
• 제23권3호
• /
• pp.306-315
• /
• 1991

본 연구는 두개의 직선 pipe가 elbow로 연결된 piping system의 내부에 유체가 흐를때 발생하는 out-of-plane 운동을 다루었으며, Extended Hamilton's principle을 이용하여 운동방정식을 유도하였다. clamped-clamped, clamped-pinned; pinned-pinned인 경계조건을 갖는 piping system의 경우, dynamic instability는 일어나지 않음을 고찰하였으며, 각 경계조건에 대한 진동수 방정식으로부터 고유진동수의 수치해를 얻었다. 유체의 속도와 Coriolis힘이 진동수에 미치는 영향을 고찰하였고, 유체의 속도와 압력이 어느값을 넘어설때 buckling-type instability가 일어남을 알았다. 그리고 유체의 속도와 압력의 함수로 등가임계속도를 정의하고 여러가지 경계조건에 대해 buckling 이 일어나는 등가임계속도를 계산하였다.